• 한국안전학회지
• /
• 제7권1호
• /
• pp.20-29
• /
• 1992

Effects of strain hardening exponents on the retardation behavior of fatigue crack propagation are experimentally investigated. The retardation of fatigue crack propagation seems to be induced by the crack closure at crack tip. The phenomenon of crack closure becomes remarkable with the increment of strain hardening exponent and magnitude of percent peak load. The ratio of crack growth increment(a$\_$d//w$\_$d/) is influenced by a single overloading (a$\_$d/) and estimated plastic zone size (W$\_$d/=2r$\_$y/) is increased according with the increasing of strain ha.dening exponents. The number of retarded crack growth cycles were (N$\_$d/) decreased as the baseline stress intensity factor .ange( K$\_$b/) was increased. Within the limitation of these experimental results obtained under the single overload, an empirical relation between crack retardation ratio (Nd/N＊), strain hardening exponent (n) and percent peak load (％PL) has been proposed as; Nd/N＊＝ exp [PL $.$ PL$.$A(n)＋B(n) ] where, A(n)＝${\alpha}$n＋${\beta}$, B(n)＝${\gamma}$n＋$\delta$, PL＝％PL/100 and ${\alpha}$＝0.78, ${\beta}$＝0.54, ${\gamma}$＝0.58 and $\delta$＝-0.01, It is interesting to note that all these constants are identical for materials such as aluminum(A3203), steel(S4SC), steel(SS41) and stainless steel(SUS316) used in this experimental study.

• 한국유체기계학회 논문집
• /
• 제17권5호
• /
• pp.72-77
• /
• 2014

Because of overload working condition of sintering cooler, the cooler fan often suffers the break or damage of rotor blade and fixing shaft. Therefore, internal flow characteristics of a steelworks sintering cooler fan by the duct shape of the cooler fan outlet, such as duct outlet opening ratio, duct height and dividing wall shape on the duct outlet flow pattern are examined in detail. The results show that relatively short duct wall height and attachment of dividing wall shape improves flow patterns considerably.

• 한국군사과학기술학회지
• /
• 제5권4호
• /
• pp.67-77
• /
• 2002

This paper introduces the calibration results of the fatigue crack growth models for damage tolerance analysis of the aircraft structures. Generalized Willenborg model and Wheeler model are calibrated with experimental data tested under the load spectrum of a trainer. The retardation factors such as, shut-off ratio in Generalized Willenborg model and shaping exponent in Wheeler model, are evaluated for aluminum alloys AL2024-T3511, AL7050-T7451 and AL7075-T73511. It is shown that the retardation effect of the crack growth rate depends on the yield strength of material and the maximum stress in the load spectrum. Generalized Willenborg model and Wheeler model give satisfactory prediction of crack growth life but the calibration of the experimental parameters with test is required.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.609-610
• /
• 2008

In this paper, a 110 dB, 1.024 MHz fourth-order single-loop Delta-Sigma sigma modulator has been presented with an over-sampling ratio of 128 and an overload factor of -6 dB for a bandwidth of 4 kHz. In particular, this ${\Sigma}-{\Delta}$ modulator is well suited for high accuracy measure systems. The whole modulator consumes only 3-mW from a single 3.3V supply in a $0.35-{\mu}m$ CMOS technology.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2000년도 종합학술발표회 논문집 Vol.10 No.1
• /
• pp.44-48
• /
• 2000

In this study was modify the PRMA for supporting various types of traffic classes such as CBR, VBR, ABR and UBR. For uplink, we use reservation slots and so the performance will not degrade in case of over load conditions. For downlink broadcasting slots for informing the status of slot reservations are used so the high priority priority terminal can preempt. And we use almost same size buffer as the frame size. So we can dynamically deal with, the traffic changes of VBR terminals. It makes easy for the terminals to reserve supplementary slots. Each terminal is reallocated by the priority of traffic classes and so we can easily select the dropping packets in case of overload conditions. As a result, using our scheme, we can get high channel efficiency and get low packet dropping ratio and delay.

• 전자공학회논문지A
• /
• 제30A권5호
• /
• pp.1-15
• /
• 1993

In DQDB networks, the bandwidth can be increased considerably be using the EN(Erasure Node) algorithms and DR(Destination Release) algorithms. However, the important issue in implementing them is using method of extra capacity fairly. To improve it, this paper proposes AEN(Adaptive Erasure Node) algorithm which erasure function is activated by network traffic load. Its functional architecture consists of SESM, RCSM, LMSM in addition to the basic DQDB state machines (DQSM, RQM). The SESM and RCSM state machines are placed in front of the DQSM and RQM state machines in order for the node to take advantage of the newly cleared slots. This paper also presents some simulation results showing the effect of AEN algorithm on access delay, throughput and segment erasing ratio in the single and multiple priority networks. The results show that the AEN algorithm offer the better performance characteristics than existing algorithms under overload conditions.

• 한국안전학회지
• /
• 제7권2호
• /
• pp.47-56
• /
• 1992

The retardation effect of fatigue crack propagation after cyclic overloading seems to be affected by strain hardening exponent. Namely, for the material with high values of n, the delay effect is found to be severe. We proposed a modified crack retardation equation which may apply the retardation of fatigue crack growth after a cyclic overloading, as (da/dN)'$_{cyc}$=($\mu$n＋λ)B $\Delta$ $K^{q}$ /[(1－ $R_{eff}$) $K_{cf}$ －$\Delta$K]. where, $R_{eff}$ is effective stress ratio [＝( $K_{min}$－K, os)/( $K_{max}$－ $K_{res}$)] The constants $\mu$＝－0.5 and λ＝0.6, and the values are found to be identical for materials such as aluminum (A 1060), steel (SS 34), brass ( $B_{s}$ SIB) and stainless steel (SUS 304) used in this investigation. (SUS 304) used in this investigation.ation.n.n.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.471-475
• /
• 2001

Planetary Speed Reducer consists of a sun gear, a planetary gear and a ring gear and if one element is fixed at this Speed Reducer, another elements operate to become a drive-axis and a subordination-axis respectively. Planetary Speed Reducer is frequently used for gear Speed Reducer because it has the advantage of having the high efficiency and getting the high Speed Reducer ratio in small space. However, it is difficult to know the current transmitted torque immediately during the use of Speed Reducer and so complicated equipment is installed in addition to protect the overload of system. The object of this paper is to design the Speed Reducer of torque- meter type that can know the torque transmitted using the power transmission feature of a simple Planetary Speed Reducer fixed at ring gear.

• 한국안전학회지
• /
• 제8권1호
• /
• pp.47-53
• /
• 1993

Residual Deformation Analysis(RDA) is a new method for ratings of the continuous bridges. The RDA makes it possible to expand the inelastic steel girder bridge design method set forth in the American Association of State Highway Officals'(AASHTO) Guide Specifications for Alternate Load Factor Design Procedures for Steel Beam Bridges Using Braced Compact Sections(1986) into an inelastic rating method. It is a method to assess the residual moments and deformations that are set up in a beam that has been loaded into the post-elastic range This method combines classical elastic conjugate beam theory with linear moment-rotation relationships for midspan inelastic positive moment. The limit state is inelastic serviceability limit. which is defined as the ratio of the span to midspan inelastic deflection(C=L/D).

• 조명전기설비학회논문지
• /
• 제25권8호
• /
• pp.140-149
• /
• 2011

This paper deals with the impact analysis of the impedance change of 345/154[kV] power transformers on the KEPCO system's overall performance. Through the steady-state and dynamic analysis of power system, the maximum available impedance of power transformers were determined. Checking violation of short-circuit current ratings and transformer overload, parallel operation of power transformers, calculation of voltage variation ratio according to the impedance changes of power transformers are included in the steady-state analysis. In addition, transient and voltage stability analysis are also performed in the study. Available magnitudes to be able to change the impedance of the transformers in KEPCO system are finally determined in the paper.