• Geomechanics and Engineering
• /
• v.29 no.6
• /
• pp.683-696
• /
• 2022

Dams are inevitably planned to be built on thick overburden with high permeability and deformability. The connection part between concrete cut-off wall in overburden and earth core in dam body is not only a key part of the anti-seepage system, but also a weak position. Large uneven settlement will be aroused at the concoction part. However, the interaction behavior and the scope of the connection part cannot be determined effectively. In this paper, numerical analysis of a high earth core dam built on thick overburden was carried out with large deformation FE method. The mechanical behavior of the connection part was detail studied. It can be drawn that there is little differences in dam integral deformation for different analysis method, but big differences were found at the connection part. The large deformation analysis method can reasonably describe the process that concrete wall penetrates into soil. The high plasticity clay has stronger ability to adapt to large uneven deformation which can reduce stress level, and stress state of concrete wall is also improved. The scope of high plasticity clay zone in the connection part can be determined according to stress level of soils and penetration depth of concrete wall.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.111-118
• /
• 2008

The purpose of this paper was to investigate the overburden effect on soil-water characteristic curve and unsaturated permeability of unsaturated weathered soils. For this, unsaturated suction and permeability tests under various overburden stress were conducted respectively. Then, the coefficient of unsaturated permeability and moisture capacity of weathered soils were estimated and compared. All these results are presented in the paper.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.10
• /
• pp.55-65
• /
• 2009

It has been well known that the infiltration of rainfall causes major surfacial slope failures in Korea. However, the hydrological and mechanical behaviors in unsaturated slopes are somewhat complex. When an analysis on unsaturated slope problems is performed, soil-water characteristics curves (SWCC) are considered as major parameters to apply. Since the weathered soil slopes are layered and stressed by overburden pressures, the response of SWCCs should account for its overburden pressure. To deal with this situation, in this study, laboratory testings were conducted to evaluate the SWCC under various overburden stress. In addition, the unsaturated shear strength was estimated using SWCC. Then the performance of unsaturated weathered soil slopes was evaluated under various conditions after applying the effect of overburden pressure on SWCCs. The results demonstrated that the effect of overburden pressure on SWCC could be substantial and the proper application to analysis is very important to enhance the prediction of slope stability.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.12
• /
• pp.107-116
• /
• 2020

The compaction grouting technique is widely used to improve the liquefaction resistance of loose sands that are liquefaction-prone. Particularly, the horizontal injection of compaction grout is proposed for the liquefiable ground with an overlying structure as it does not allow the vertical compaction grouting. However, there has been limited number of researches on the horizontal compaction grouting. Therefore, this study explores the grout bulb shape and expansion direction in loose sand. A series of scaled two-dimensional experiments on the horizontal compaction grouting was conducted varying the overburden stress. The results show that the grout bulb grows in an elliptical shape though its directivity of major axis changes with the overburden effective stress and relative density. The grout bulb expands faster in a horizontal direction under a low overburden stress with a small relative density. The higher overburden stress and the greater relative density cause the more circular shape with the faster expansion in a vertical direction. The presented finding is expected to contribute to accurate and efficient design of the horizontal compaction grouting method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.1
• /
• pp.63-71
• /
• 2018

In this study, the torque and horizontal stress acting on vane were measured and then used to determine a friction angle of sand. A dry Nakdong River sand was prepared for loose and dense conditions in a cell and then pressurized with 25, 50, 75 or 100 kPa from the surface of sand. A vane (5cm in diameter and 10cm in height) was rotated and the torque and horizontal stress were measured at real time. A maximum torque was 3.5-9.5Nm for loose sand and 7.4-17.6Nm for dense sand, respectively. The maximum torque increased as an overburden pressure increased. The maximum torque obtained at 14-20 degrees of vane rotation, which was not influenced by the initial alignment of earth pressure and vane blade. An initial horizontal stress ratio was 0.33-0.35 on the average. The horizontal stress increased initially and then decreased due to particle disturbance. A friction angle was calculated from real time varying horizontal stress and torque, which decreased with increasing overburden pressure. The friction angle of loose sand from vane shear test was similar to that of direct shear test but that of dense sand was overestimated.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.7 no.3
• /
• pp.227-237
• /
• 2005

In this study, the behavior of shallow 2-Arch tunnel due to excavation under horizontal discontinuity plane was verified experimentally. The model tests were carried out by varying the overburden height and the location of the discontinuity plane. The model tests followed exactly the real 2-Arch tunnel construction stages. As a result, it is discovered that stress-transfer mechanism and loosening area around the 2-Arch tunnel depends on the overburden heights and the location of the discontinuity plane. And central pillar load is also dependent on overburden height, location of discontinuity plane and construction stages.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.4 no.1
• /
• pp.71-78
• /
• 2002

In this study, the influence of the presence of discontinuity planes on the load transfer mechanism and the pattern of loosening zone was studied based on the laboratory test. The trap-door and the reaction plates are installed as the bottom plane of the model box. The vertical discontinuity plane is installed in the dry sand. Various overburden heights and locations of discontinuity planes are applied as major factors in this study. The results show that at higher overburden heights over about 1.5 times the excavation width, the ratio of the transferred stress to the insitu stress converges to a certain value even if the overburden height increases further. The results also show that the discontinuity plane gives relatively larger influence on the load transfer mechanism, that produces the unsymmetrical load concentration, when the discontinuity plane locates within the tunnel width. When the discontinuity plane locates outside the tunnel width, the unsymmetrical load concentration is reduced considerably.

• Geomechanics and Engineering
• /
• v.28 no.6
• /
• pp.613-624
• /
• 2022

A study of the evolution of overburden fractures under the solid-fluid coupling state was conducted based on the geological and mining characteristics of the coal seam depth, weak strata cementation, and high-intensity mining in the mining areas of West China. These mining characteristics are key to achieving water conservation during mining or establishing groundwater reservoirs in coal mines. Based on the engineering background of the Daliuta Coal Mine, a non-hydrophilic simulation material suitable for simulating the weakly cemented rock masses in this area was developed, and a physical simulation test was carried out using a water-sand gushing test system. The study explored the spatial distribution and dynamic evolution of the fractured zone in the mining overburden under the coupling of stress and seepage. The experimental results show that the mining overburden can be vertically divided into the overall migration zone, the fracture extension zone and the collapse zone; additionally, in the horizontal direction, the mining overburden can be divided into the primary fracture zone, periodic fracture zone, and stop-fracture zone. The scope of groundwater flow in the overburden gradually expands with the mining of coal seams. When a stable water inrush channel is formed, other areas no longer generate new channels, and the unstable water inrush channels gradually close. Finally, the primary fracture area becomes the main water inrush channel for coal mines. The numerical simulation results indicate that the overlying rock breaking above the middle of the mined-out area allows the formation of the water-conducting channel. The water body will flow into the fracture extension zone with the shortest path, resulting in the occurrence of water bursting accidents in the mining face. The experimental research results provide a theoretical basis for the implementation of water conservation mining or the establishment of groundwater reservoirs in western mining areas, and this theoretical basis has considerable application and promotion value.

• Structural Engineering and Mechanics
• /
• v.61 no.5
• /
• pp.637-643
• /
• 2017

Carbon fiber reinforced polymers (CFRPs) have been recently investigated as an alternative material for Geosynthetics to improve soil properties. One of the factors influencing the fiber orientation and mechanical properties of CFRP is the effect of soil overburden pressure. This study investigates the tensile behavior of cast-in-place CFRP. During the curing time of specimens, a wide range of normal stress is applied on specimens sandwiched between the soils. Two different soil types are used to determine the effect of soil grain size on the mechanical properties of CFRP. Specimens are also prepared with different specifications such as curing time and mixing soil in to the epoxy. In this study, tensile tests are conducted to investigate the effect of such parameters on tensile behavior of CFRP. The experimental results indicate that by increasing the normal stress and soil grain size, the ultimate tensile strength and the corresponding strain of CFRP decrease; however, reduction in elastic modulus is not noticeable. It should be noted that, increasing the curing period of epoxy resin and mixing soil in to the epoxy have no significant effect on the tensile properties of CFRP.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.11
• /
• pp.151-158
• /
• 2006

Centrifuge tests have shown that a uniformly placed sand layer will first initiate liquefaction near the surface and that liquefaction will progress downward during shaking. This appears to be in conflict with the overburden stress effect on soil liquefaction (i.e., $K_0$ effect) observed in laboratory testing. This discrepancy can be explained by stress-induced densification at depth which overcomes the effect of confining stress on liquefaction resistance. Stress densification occurs in centrifuge model tests but its effect has generally not been considered when preparing or evaluating centrifuge models. A new centrifuge model preparation method is proposed by considering stress-induced densification upon spin-up. The proposed method can be used to explore $K_0$ effects. The method is supported in this study by numerical predictions.