• Journal of the Korean Applied Science and Technology
• /
• v.17 no.2
• /
• pp.113-119
• /
• 2000

Alkylation of phenol with tert-butanol in the liquid phase on mordenite was studied. The influence of many reaction parameters such as calcination temperature, reaction temperature, t-butanol/phenol molar ratio on catalytic properties was discussed. The main products were 2,4-di-t-butylphenol, o-t-butylphenol, p-t-butylphenol, the last of these was wanted product. In order to enhance the selectivity of p-t-butylphenol, optimum conditions were recommended at $500^{\circ}C$ calcination temperature, $140^{\circ}C$ reaction temperature, 1.0 molar ratio of reactants over mordenite. P-t-butylphenol was formed with 90% isomer selectivity at optimum conditions after 4hr reaction. On the basis of the behavior obtained in the cases mentioned, optimum conditions and catalytic properties for t-butylation of phenol were provided.

• Tribology and Lubricants
• /
• v.3 no.2
• /
• pp.68-71
• /
• 1987

This paper deals with some thermal Characteristics of journal bearing such as the behaviour of the maximum bearing temperature, the lubricant's carry-over in the inlet region and so on. Temperatures of the bearing and the lubricants being supplied and discharged were measured along with shaft speed and bearing load. The results showed that with the increase of the Shaft speed, the maximum temperature rose at any shaft speed at a defferent rate of change defending on the flow regime of the lubricant film. And the lower eccentricity ratio is the more lubricant's carry-over occur. Additionally it was partially proved that the oil discharge temperature and the maximum temperature changed in quite different each other.

• Journal of the Korean Home Economics Association
• /
• v.23 no.1
• /
• pp.19-24
• /
• 1985

The effect of temperature, washing time, mechanical agitation and concentration on the removal from cotton fabrics of tripalmitin labelled with C\sup 14\ were studied. In order to correlate the detergency with the removal mechanism, solubilization and suspending power of surfactants were observed. RESULTS : 1. The detergency from cotton fabric was increased with elevating temperature and over the temperature of maximum detergency, the rate of soil removal was rather decreased. 2. The effects of washing time and mechanical agitation on the removal of triplamitin were obvious at lower temperature. 3. The removal of tripalmitin was remarkably increased at higher concentration over cmc for all surfactants. The detergency of nonionic surfactant -NPPG- was best, this was resulted from its large solubilization and suspending power.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.396-400
• /
• 2003

This paper has studied thermal characteristics of machine tool to develope high speed spindle and optimum design condidering the thermal deformation. Comparing the test data of temperature measurement and structural analysis data using FEM, we verifiedthe test validity and predicted thermal deformation, influence of spindle generation of heat, and established cooling system to prevent the thermal deformation. 1) The temperature rise of spindle system depends on increasing number of rotation and shows sudden doubling increment of number of rotation over 7,000rpm. 2) Oil jacket cooling can be effective cooling method below 8,000rpm but, over 8,000rpm, it shows the decrement of cooling effect. 3) Comparing FEM analysis results and revolution test results, we can confirmn approximate temperature change consequently, it is possible to simulate temperature rise and thermal distribution on the inside of spindle system. 4) We can confirm that simulated approach by FEM analysis can be effective method in thermal-appropriate design..

• Coupled systems mechanics
• /
• v.8 no.6
• /
• pp.501-522
• /
• 2019

The present study is concerned with the thermoelastic interactions in a two dimensional axisymmetric problem in transversely isotropic thermoelastic solid using new modified couple stress theory without energy dissipation and with two temperatures. The Laplace and Hankel transforms have been employed to find the general solution to the field equations. Concentrated normal force, normal force over the circular region, concentrated thermal source and thermal source over the circular region have been taken to illustrate the application of the approach. The components of displacements, stress, couple stress and conductive temperature distribution are obtained in the transformed domain. The resulting quantities are obtained in the physical domain by using numerical inversion technique. The effect of two temperature varying by taking different values for the two temperature on the components of normal stress, tangential stress, conductive temperature and couple stress are depicted graphically.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.8
• /
• pp.1046-1052
• /
• 2001

This study has been performed experimentally to measure the frost properties over a cold flat plate in order to obtain the correlations of the frost properties with various environmental parameters. Correlations of the frost surface temperature, thickness, density, and thermal conductivity are presented along with the experimental results as a function of environmental parameters, distance from the leading edge of test plate, and time. These correlations can be used to predict the frost properties with a maximum error of 8% in the following ranges : air temperature 15∼25$\^{C}$, relative humidity 60∼80%, air velocity 1∼3m/s and cooling plate temperature -15∼-25$\^{C}$.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.980-984
• /
• 2002

This paper has studied thermal characteristics of machine tool to develope high speed spindle and optimum design condidering the thermal deformation. Comparing the test data of temperature measurement and structural analysis data using FEM, we verified the test validity and predicted thermal deformation, influence of spindle generation of heat, and established cooling system to prevent the thermal deformation. 1) The temperature rise of spindle system depends on increasing number of rotation and shows sudden doubling increment of number of rotation over 7,000rpm. 2) Oil jacket cooling can be effective cooling method below 8,000rpm but, over 8,000rpm, it shows the decrement of cooling effect. 3) Comparing FEM analysis results and revolution test results, we can confirm approximate temperature change consequently, it is possible to simulate temperature rise and thermal distribution on the inside of spindle system. 4) We can confirm that simulated approach by FEM analysis can be effective method in thermal-appropriate design.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.1 s.232
• /
• pp.159-168
• /
• 2005

In recent studies, it was reported that there existed the temperature discontinuity at a liquid-vapor interface in an equilibrium state. However, from the viewpoint of the classical thermodynamics, it is highly questionable result although considering that the experiments related with a boundary layer is very difficult due to the extremely thin thickness of it. To clarify whether the temperature discontinuity over a liquid-vapor interface really exists, the computer simulations were performed. From the simulation results, it could be concluded that the misconception in a temperature calculation might result in non-uniform temperature distributions over an interface under an equilibrium state.

• Solar Energy
• /
• v.5 no.2
• /
• pp.20-27
• /
• 1985

The aims of this study is to examine closely the temperature distribution of the solar pond for conditions of Seoul area climate and to prove capability of the solar pond utilization in Seoul area. In this study the equations for the convecting zone temperature of the solar pond were derived from Rabl and Nielsen's model. As the result of computer simulation, it was found that the average temperature of convecting zone is over $100^{\circ}C$ under conditions which is no output and 120cm depth or over of the insulating layer. Consequently if solar pond is constructed in Seoul area, it is a effective heat storage system.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.498-503
• /
• 2002

This paper has studied thermal characteristics of machine tool to develope high speed spindle and optimum design considering the thermal deformation. Comparing the test data of temperature measurement and structural analysis data using FEM, we verified the test validity and predicted thermal deformation, influence of spindle generation of heat, and established cooling system to prevent the thermal deformation. 1) The temperature rise of spindle system depends on increasing number of rotation and shows sudden doubling increment of number of rotation over 7,000rpm. 2) Oil jacket cooling can be effective cooling method below 8,000rpm but, over 8,000rpm, it shows the decrement of cooling effect. 3) Comparing FEM analysis results and revolution test results, we can confirmn approximate temperature change consequently, it is possible to simulate temperature rise and thermal distribution on the inside of spindle system. 4) We can confirm that simulated approach by FEM analysis can be effective mettled in thermal-appropriate design.