• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.517-520
• /
• 2006

The waterproofing of Building on the roof has been exposed more underground or the other part of waterproofing than environmental factor(solar heat, UV, salt, acid rain, wind, temperature, snow, rain, etc.) or physical factor. So it must be have a waterproofing performance and it has a special technique for the maintaining of concrete durability. Therefore, exposed waterproof layer has to protected from UV, solar heat, rain and the outside environment also, to endurance durability methods spread face plate topcoat material on the waterproof layer. But, actuality faceplate waterproof layer of topcoat materials are unbearable to UV, solar heat and moisture etc. and it doesn't have adhesion with waterproof layer in the middle. So it happens to crack, separating and heaving etc. Therefore, in the study, we will suggest that using of the exposed roof waterproof layer topcoat materials test method manage rooftop waterproof layer for the durability and the stability.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1376-1378
• /
• 1999

Most conventional protection relays are based on processing information in the spectrum that is close to or at power frequency. It is, however, widely known that faults on transmission lines produce frequency components of a wide range In this respect, this paper describes the basis of a Protection technique for transmission lines which utilises high-frequency components. Fault-generated signals caused by post-fault and the signal derived from stack tuner is connected to the coupling capacitor of CVT. Digital signal processing is then applied to the captured information to determine whether the fault is inside or outside the Protected zone, and to discriminate the fault type on transmission line.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.334.1-334
• /
• 2002

In this study, a cross-flow fan system used in indoor unit of the split-type air conditioner is analyzed by computational simulation. A commercial CFD code - Fluent - is used to calculate the performance and its unsteady flow characteristics. The unsteady incompressible Wavier-Stokes equations are solved using a sliding mesh technique on the interface between rotating fan region and the outside. The acoustic pressure is calculated by using Ffowcs-Williams and Hawkings equation. (omitted)

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.232-239
• /
• 2006

Guided wave techniques have been used for pipeline inspection because of the long range inspection capability of guided waves. One of main concerns of these technique is how ones decide the axial interval of sensors when they are utilized for pipeline inspection. This question is related to the characteristic of cylindrical guided wave propagation, especially wave attenuation. Thus, attenuation of fundamental longitudinal guided wave propagating liquid-filled steel pipes is numerically investigated in the paper. Several liquids such as water, diesel oil, castor oil etc. are considered for the filing materials in the pipes. Sink is considered for numerical models for abandoning standing wave modes; hence, the attenuation dispersion curves become much simpler. Those attenuation calculations can be utilized for guided-wave-based nondestructive testing of pipelines when one inspects pipelines, using monitoring sensors, which are installed outside pipes.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.268-272
• /
• 2014

This letter presents a measurement methodology of the complex permittivity of liquid using a partially open cavity in narrow band. The partially open cavity (POC) can measure dielectric small changes caused by the temperature variation of the liquid inside the cavity as well. Using the resonance frequency and unloaded quality factor of the proposed POC, the complex permittivity is evaluated. The apertures on the walls of the cavity are designed to circulate the liquid inside to outside of the POC and located at the corner area of the cavity to minimize the disturbance of field distribution at the dominant mode. The results measured by the proposed POC were compared with those by the conventional open-ended probe and Cole-Cole equation. The POC showed better performance in measuring small dielectric constant changes than the open-ended probe.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.4
• /
• pp.791-796
• /
• 2001

Friction stir welding is a solid phase welding process that does not melt the metal when welding. The FSW is the most remarkable and potentially useful new welding technique that is still in development. Friction stir butt welding process on 2 mm thick Al 1050 plates by utilizing a milling machine was experimentally studied. With the optimized heat generating tool welds could be achieved that are void and crack free. It was found that the friction stir welded tensile test specimens failed in the HAZ outside of the weld metal, and that the tensile strength was above 90% of that of the base metal.

• Korean Journal of Animal Reproduction
• /
• v.19 no.3
• /
• pp.181-189
• /
• 1995

In this study, methods on fabrication of microtool and setting of micromanipulator were examined and relationship between first polar body extrusion rate and maturation time of follicular oocyte, enulceation rae and repetition of trial, and enucleation rate and maturation period were investigated. The results are as follows: 1. Suitable outside diameter of micropipette tube was 1mm. Holding pipette with less than diameter of oocyte was fitred for manipulation, and zona dissection needle was easily operated when its sharp-point had diameter of about 8 ${\mu}{\textrm}{m}$ and length of 300${\mu}{\textrm}{m}$. The injection pipette with 20~35${\mu}{\textrm}{m}$ outside diameter was adequate for injection of blastomere into perivitelline space. 2. Separation of blastomere was effective when zona pellucida had cut with zonadissection needle and the embryo was pipetted gently with the pipette that had narrower diameter than that of embryo until separation of blastomeres had completed. 3. The extrusion rate of first polar body was 78% during 20~24% hours incubation for maturation. 4. According to repetitions of micromanipulation, the enucleation rate was increased to 85% and the time required for enucleation of a oocyte was shortened to 3 min. 5. The extrusion rate of first polar body and enucleation rate were 82 and 76% respectively, in the group of the oocytes cultured for 22 hours. However in the group cultured for 24 hours, the extrusion rate of first polar body and enucleation rate were 53 and 100% respectively.

• Nuclear Engineering and Technology
• /
• v.50 no.6
• /
• pp.989-995
• /
• 2018

Argonne National Laboratory of the United States and Kharkov Institute of Physics and Technology (KIPT) of Ukraine have cooperated on the development, design, and construction of a neutron source facility. The facility was constructed at Kharkov, Ukraine, and its commissioning process is underway. The facility will be used for researches, producing medical isotopes, and training young nuclear specialists. The neutron source facility is designed with a provision to include a cryogenically cooled moderator system-a cold neutron source (CNS). This CNS provides low-energy neutrons, which will be used in the scattering experiment and material structures analysis. Cold neutron guides, coated with reflective material for the low-energy neutrons, will be used to transport the cold neutrons to the experimental site. The cold neutron guides would keep the cold neutrons within certain energy and angular space concentrated inside, while most of the gamma rays and high-energy neutrons are not affected by the cold neutron guides. For the KIPT design, the cold neutron guides need to extend several meters outside the main shield of the facility, and curved guides will also be used to remove the gamma and high-energy neutron. The neutron guides should be installed inside a shield structure to ensure an acceptable biological dose in the facility hall. Heavy concrete is the selected shielding material because of its acceptable performance and cost. Shield design analysis was carried out for the CNS guide hall. MCNPX was used as the major computation tool for the design analysis, with neutron and gamma dose calculated separately. Weight windows variance reduction technique was also used in the shield design. The goal of the shield design is to keep the total radiation dose below the $5.0{\mu}Sv/hr$ guideline outside the shield boundary. After a series of iterative MCNPX calculations, the shield configuration and parameters of CNS guide hall were determined and presented in this article.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.5
• /
• pp.481-487
• /
• 2005

Proposed induction-heated system is innovative system which applied special high-frequency power circuit technique for thermal converse technique and IH(Induction-Heating) magnetic induction heating generated from induction-heated metallic package that is for distillation unit. In this occurs not burning, so that the working environment can be improved. This electromagnetic induction heating technique is used high frequency inverter, By using high frequency inverter high frequency alternative current in the range of [kHz] can be made with conventional alternative current. In this contribution IGBT module is used for high frequency inverter. This paper proposes new fluid heating method. Which is operated as follows. Working coil, which is wrapped outside of pipeline, makes the eddy current. Inside of heating vessel in isolated pipeline the specially designed stainless metallic package is inserted, which can be heated by eddy current losses. And then In this paper are discussed action analysis and characteristics analysis of 5[kW] class full-bridge resonant inverter system and resonant metallic package. In addition, by using this system, how high-efficiency heater is developed and application of system are also discussed.

• Journal of Internet Computing and Services
• /
• v.9 no.1
• /
• pp.115-127
• /
• 2008

The component for satisfying several domain requirements must be developed to support variety. But, when the application is developed using the component, it happens other requirements. So, it is difficult to design component to satisfy severaldomain requirements. Also, it is impossible to support the special business logic. As this problem, the component must provide to the white-box component, it is not the black-box component. So, in this paper, we propose the variability design technique and the customization technique using the design technique that can support the various requirements. This technique is not focus on designing the component to analyze various domains. The variability of the component is designed to the initial variability in the component development phase and we use the customization technique for applying the variability to developing application. The variability can be re-designed during developing the application to use the component applying the variability. The variability of the component is evolved and the generation of the component is increased via the iteration Generally, the range of the component variability is classified the function modification within the component and the component internal structure modification as requirements in the component outside. As the range of the variability, we propose the variability design technique of the behavior and the message flow. This paper proposes a message flow design technique for modifying function call.