• 조명전기설비학회논문지
• /
• 제16권5호
• /
• pp.61-65
• /
• 2002

SRM 토크는 인덕턴스 프로파일과 전류에 의해 발생한다. 발생한 SRM 토크는 전류제어시 turn-off 각을 제어함으로써 최대화 할 수 있고, 본 논문에서는 최소자승법을 이용하여 구한 함수를 통해 Turn-off 각을 제어할 수 있는 방안을 제안하였다. 시뮬레이션은 3상 6/4극 SRM을 대상으로 하였고, 제안한 방법에 의해 최대 평균토크가 됨을 시뮬레이션을 통해 증명하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 학술대회 논문집 정보 및 제어부문
• /
• pp.318-319
• /
• 2008

In this paper, a steering feel simulator is designed and implemented using a steering wheel with a rotation angle sensor, torque sensor, and an ac motor for the generation of the required torque. The controller in the simulator consists of a 16-bit micro-controller, a D/A converter and A/D converters. The main objective of the controller is to perform torque control where the reference torque is calculated from the torque map for both the vehicle velocity and the wheel sensor cutout. It is shown via the experimentation using the proposed simulator that the simulator output performance can be easily understood for the variation of vehicle parameters or controller parameters.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2009년도 정기총회 및 추계학술대회 논문집
• /
• pp.139-141
• /
• 2009

This paper presents a design and analysis of torque characteristics of a two-phase SRM(Switched Reluctance Motor) for high speed blower system. To reduce the electrical frequency and core losses at high speed region, In order to reduce torque ripple and torque dead-band, variable rotor air-gap structure is adopted and the air-gap is optimized according to torque production. The optimized torque output is verified by the FEM results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.702_703
• /
• 2009

Electric Power Steering(EPS) system is superior to conventional Hydraulic Power Steering(HPS) system in aspect of fuel economy and environmental concerns. The EPS system consists of torque sensor, electric motor, ECU(Electric Control Unit), gears and etc. Among the elements, the torque sensor is one of the core technologies of which output signal is used for main input of EPS controller. Usually, the torque sensor has used torsion bar to transform torsion angle into torque. The torsion angle of both ends of a torsion bar is measured by a contact variable resistor. In this paper, the sensor is accurately analyzed using 3D finite element method and its characteristics with respect to four different shapes of the stator teeth are compared. The four shapes are rectangular, triangular, trapezoidal and circular type.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.561-566
• /
• 2000

A screw driver is essentially used in assembling machine parts and electronic products such as the printed circuit board with a housing. As the parts to be assembled becomes small and precise, the higher precision of the controling screw driver torque is required. However, because the operator controls the fastening torque by his experience, it must be inexact. Thus the screw driver which can exactly control the fastening torque by a bellows is designed and developed in the study. The bellows is expanded by the inner air pressure and contracted and by the spring operation. The bellows driver is composed of the entrance solenoid valve, the exit solenoid valve and the pressure sensor. The pressure sensor senses the bellows pressure. When the pressure sensor output reaches the setting value, it operates the exit solenoid valve not to deliver further torque by letting the air of the bellows out. Through a series of experiments, the performance is studied and verified.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.853-854
• /
• 2006

Interior permanent magnet synchronous motor(IPMSM) has higher power density than other PM(permanent Magnet) machines due to reluctance torque in addition to magnetic torque, and the ratio of magnetic and reluctance torque has influences on motor characteristics such as input current, efficiency, power factor, etc. Therefore, this paper presents the output characteristics of IPMSM according to the ratio magnetic and reluctance torque of IPMSM and discuss the design strategy of IPMSM.

• 한국군사과학기술학회지
• /
• 제8권3호
• /
• pp.18-23
• /
• 2005

Ships have been propelled and maneuvered by electrical drives since trle late seventies. Recently, rare earth PMs allow the design of brushless motors with very high efficiency over a wide speed range. This is the most important factor in ship propulsion technology. Several types PM motors have been developing for ship propulsion system. However these have disadvantage such as cogging torque. It causes an undesired effect that contributes to output ripple, vibration, and noise of machine. Therefore several techniques may be adopted in designing PM motor in order to reduce the cogging torque. This paper describes cogging torque receding methods such as adjusting arigap length, magnet arc, and magnet thickness. That are analysed by using the finite element method(FEM) and the maxwell stress tensor method.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 추계학술대회 논문집
• /
• pp.53-56
• /
• 2002

This paper presents neural observer that used to deadbeat load torque observer. Most practical systems are nonlinear, and it is general practice to use linear models to simplify their analysis and design. However, the locally linearized model is invalid for a large signal change. The neural observer is suggested to increase the performance of the load torque observer and main controller The output error and estimeted state is trianed by neural network of neural observer. As a result, the state estimation error is minimised and deadbeat load torque observer make use of corrected esimation state. To reduce of the noise effect of deadbeat load torque observer, the post-filter which is implemented by MA process, is adopted. As a result, the proposed control system becomes a robust and precise system against the load torque. A stability and usefulness, through the verified computer simulation, are shown in this paper.

• Journal of Power Electronics
• /
• 제11권3호
• /
• pp.342-349
• /
• 2011

We propose a torque and pitch control scheme for variable speed wind turbines with permanent magnet synchronous generator (PMSG). A torque controller is designed to maximize the power below the rated wind speed and a pitch controller is designed to regulate the output power above the rated wind speed. The controllers exploit the sliding mode control scheme considering the variation of wind speed. Since the aerodynamic torque and rotor acceleration are difficult to measure in practice, a finite time convergent observer is designed which estimates them. In order to verify the proposed control strategy, we present stability analysis as well as simulation results.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.64.4-64
• /
• 2002

$\textbullet$ Contents 1 Introduction $\textbullet$ Contents 2 Problem Statement $\textbullet$ Contents 3 Adaptive Output Feedback Control Design $\textbullet$ Contents 4 Stability analysis $\textbullet$ Contents 5 Simulation Result $\textbullet$ Contents 6 Conclusions