• 대한기계학회논문집B
• /
• 제20권11호
• /
• pp.3666-3675
• /
• 1996

A new hardware temperature compensation method for hot-wire anemometer is investigated and an analog compensating circuit is proposed in this article. A photoconductive cell is introduced here as a variable resistor in the anemometer bridge and the linearized output of a thermistor is used to monitor the input of the photoconductive cell. In contrast with the conventional method, any type of temperature sensor can be used for compensation if once the output of thermometer varies linearly with temperature. So the present technique can diversify the compensating means from a conventional passive compensating resistance to currently available thermometers. Because the resistance of a photoconductive cell can be set precisely by adopting a stabilizing circuit whose operation is based on the integration function of the operational amplifier, the accuracy of compensation can be enhanced. As an example of linearized thermometer, thermistor sensor whose output is linearized by a series resistor was used to monitor the fluid temperature variation. Validation experiment is conducted in the temperature ranged from 30 deg. C to 60 deg. C and the velocity up to 40 m/s. It is found that the present technique can be adopted as a compensating circuit for anemometer and hot-wire type airflow meter.

• 한국전기전자재료학회논문지
• /
• 제13권4호
• /
• pp.273-279
• /
• 2000

Electrical repair method which has replaced laser repair method can replace defective cell by redundancy’s in the redundancy scheme of conventional high density memory. This electrical repair circuit consists of the antifuse program/read/latch circuits, a clock generator a negative voltage generator a power-up pulse circuit a special address mux and etc. The measured program voltage of made antifuses was 7.2~7.5V and the resistance of programmed antifuses was below 500 Ω. The period of clock generator was about 30 ns. The output voltage of a negative voltage generator was about 4.3 V and the current capacity was maximum 825 $mutextrm{A}$. An antifuse was programmed using by the electric potential difference between supply-voltage (3.3 V) and output voltage generator. The output pulse width of a power-up pulse circuit was 30 ns ~ 1$mutextrm{s}$ with the variation of power-up time. The programmed antifuse resistance required below 44 ㏀ from the simulation of antifuse program/read/latch circuit. Therefore the electrical repair circuit behaved safely and the yield of high densitymemory will be increased by using the circuit.

• 한국전기전자재료학회논문지
• /
• 제26권8호
• /
• pp.575-581
• /
• 2013

The self-cascode (SC) structure has low output voltage swing and high output resistance. In order to implement a simple and better SC structure, the native-$V_{th}$ MOSFETs which has low threshold voltage($V_{th}$) is applied. The proposed SC structure is designed using a qualified industry standard $0.18-{\mu}m$ CMOS technology. Measurement results show that the proposed SC structure has higher transconductance as well as output resistance than single MOSFET. In addition, analog building blocks (e.g. current mirror, basic amplifier circuits) with the proposed SC structure are investigated using by Cadence Spectre simulator. Simulation results show improved electrical performances.

• 한국안전학회지
• /
• 제34권1호
• /
• pp.21-26
• /
• 2019

This paper is purposed to develop hardware for controlling abnormal temperature that can occur environment and component itself in PCS. In order to be purpose, the hardware which is four part(sensing, PLC, monitoring and output) keep detecting temperature for critical components of PCS and can control the abnormal temperature. Apply to the hardware, it is selected to PV power generation facilities of 20 kW in Cheong-ju city and measured the data for one year in 2017. Through the temperature data, it is found critical components of four(discharge resistance, DC capacitor, IGBT, DSP board) and entered the setting value for operating the fan. The setting values for operating the fan are up to $130^{\circ}C$ in discharge resistance, $60^{\circ}C$ in DC capacitor, $55^{\circ}C$ in IGBT and DSP board. The hardware is installed at the same PCS(20 kW in Cheong-ju city) in 2018 and the power generation output is analyzed for the five days with the highest atmospheric temperature(Clear day) in July and August in 2017 and 2018 years. Therefore, the power generation output of the PV system with hardware increased up to 4 kWh.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.225-227
• /
• 2006

Multilayer step down piezoelectric transformers were manufactured using PZN-PMN-PZT and PMN-PNN-PZT ceramics respectively. Sintering temperature of the ceramics was $940^{\circ}C$. And then. their electrical properties were investigated according to the variations of frequency and load resistance. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum values in the vicinity of 69 and 71kHz, respectively. At the load resistance of $100{\Omega}$, the piezoelectric transformers showed the temperature rises of about 21 and $18^{\circ}C$ at the output power of 15W and 18W, respectively. At the transformer with high effective electromechanical coupling factor($k_{eff}$), lower temperature increase was appeared.

• Journal of electromagnetic engineering and science
• /
• 제2권1호
• /
• pp.5-10
• /
• 2002

We have analized the inverse class-F and class-F amplifiers using their waveforms. From the analytic equations derived from the analysis, we have calculated tole efficiencies, output powers, DC power dissipations, and optimum fundamental load impedances of the inverse class-F and class-F amplifiers. We also have compared them for various operation conditions, which include the same peak current, saute DC power dissipation, same fundamental RF output power, and same fundamental load impedance with different Ron(on-resistance). These analyses have clearly shown the performance limitations, advantages, and guide to the optimized design of the inverse class-F amplifiers.

• 한국전기전자재료학회논문지
• /
• 제14권4호
• /
• pp.289-296
• /
• 2001

The piezoelectric transformers of 2.0x10x48 ㎣ size were fabricated with PSN-PMN-PZT(T10 and PNW-PMN-PZT(T2) composition ceramics. Effects of micro structural and piezoelectric properties on the electrical characteristics of the piezoelectric transformers were investigated. Under the fixed output power of 6 W, temperature rise of T1 transformer at the optimum load was smaller than T2 one because of fine grain size effect. Voltage step-up ratio of T1 transformer showed higher value than T2 one T1 transformer showed an excellent properties with voltage step-up ratio of 12.41, efficiency of 95.23% and temperature rise of 7.2$^{\circ}C$ at 200㏀ load resistance. And also, T2 transformer showed an excellent properties with voltage step up ratio of 9.81, efficiency of 95.51% and temperature rise of 9$^{\circ}C$ at 150㏀ load resistance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 B
• /
• pp.423-425
• /
• 1998

In this paper, a novel Programmable Signal Conditioner(PSC) for Thermo Couple(T/C) without variable-resistance is proposed. It is fabricated by using a fully digitalized error-correction and calibration algorithm. In signal processing of T/C, since the output voltage of T/C is nonlinear and its level is very low, the circuitry become very complicated to reduce the converting error and identify the true thermal voltage signal. The newly proposed PSC has compensation and calibration algorithm not using variable resistor. Moreover structure can be very simple and it has highly precise output characteristics.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.1035-1046
• /
• 2015

This study presents a practical implementation of a multi-mode two-phase interleaved boost converter for fuel cell electric vehicle application. The main operating modes, which include two continuous conducting modes and four discontinuous conducting modes, are discussed. The boundaries and transitions among these modes are analyzed with consideration of the inductor parasitic resistance. The safe operational area is analyzed through a comparison of the different operating modes. The output voltage and power characteristics with open-loop or closed-loop operation are also discussed. Key performance parameters, including the DC voltage gain, input ripple current, output ripple voltage, and switch stresses, are presented and supported by simulation and experimental results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.301-303
• /
• 2006

In this study, multilayer piezoelectric transformer were manufactured using the PZN-PMN-PZT ceramic and then the electrical characteristics were investigated. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value in the vicinity of 78.16kHz and increased according to the increase of load resistance. When the output impedance coincided with the load resistance, piezoelectric transformer showed the temperature increase of about $20^{\circ}C$ at the output power of 12W. The results, the multilayer transformer manufactured using the low temperature sintered PZN-PMN-PZT ceramics can be stably driven for step-up transformers.