• International Journal of Concrete Structures and Materials
• /
• v.4 no.1
• /
• pp.55-62
• /
• 2010

The performance evaluation of a sodium lauryl sulfate to qualify as a foaming agent is presented in this paper. When new surfactants are used a systematic study of production parameters on the foam characteristics needs to be undertaken unlike proprietary foaming agents and foam generator for which manufacturer has predefined the parameters. The relative influence of the foam parameters and optimization of factors were carried out through a systematic experiment design. The foam production parameters namely foam generation pressure and dilution ratio of foaming agents are observed to have significant effect on all foam characteristics with the exception of foam output rate on which only foam generation pressure has influence. The foam with good initial foam density need not necessarily be stable foam. The optimum levels of foam production parameters are determined for the surfactant Sodium lauryl sulfate which can be used to produce stable foam for foam concrete production.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.403-405
• /
• 2008

This paper proposes an output inductor-less active clamp forward converter employing current boost-up circuit for high power density adaptor. By applying the proposed current boost-up circuit, the proposed converter has low conduction loss and low voltage ringing of the secondary rectifier. This paper presents the analysis of the proposed converter and a comparison between the proposed converter and the conventional converter through experiment.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.382-384
• /
• 2008

Hold-up time is a special requirement for the front end DC/DC converter in a server power supply. It forces the converter with the variable switching frequency to operate in a wide switching frequency range, which makes the regulation difficult and reduces the power density. In this paper a novel frequency controlled half bridge converter with the hold-up time extension circuit is proposed. During the hold-up time, the auxiliary switches are turned on, thus the resonant inductance is reduced and the voltage conversion ratio is increased. Therefore, the output capacitor of the power factor correction (PFC) circuit can be decreased, and the converter can have high power density. The proposed converter is verified by experimental results from a prototype with 700W, 400V input, and 12V output.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1421-1428
• /
• 2015

The efficiency and reliability of the dual-buck inverter (DBI) were greatly improved by eliminating the shoot-through problem and optimally designing the freewheeling diode. The traditional DBI suffers from large harmonic components with low output voltage and large capacity output filter inductor. To overcome the aforementioned disadvantages, a modified DBI (MBDI) was proposed by adopting a quasi-resonant link and pulse density modulation (PDM). This paper first introduces the working principle of the MBDI and PDM, and then the selection principle of system parameters is presented. Finally, a mathematical model of the MBDIis built, and an experiment prototype is set up. Simulation and experimental results verify the correctness of the theoretical analysis and the feasibility of the scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.427-432
• /
• 2005

This paper is concerned with a simultaneous design of TSK (Takagi-Sugeno-Kang)-linguistic fuzzy models with uncertain model output and the computationally efficient representation. For this purpose, we use the fundamental idea of linguistic models introduced by Pedrycz and develop their comprehensive design framework. The design process consists of several main phases such as (a) the automatic generation of the linguistic contexts by probabilistic distribution using CDF (conditional density function) and PDF (probability density function) (b) performing context-based fuzzy clustering preserving homogeneity based on the concept of fuzzy granulation (c) augment of bias term to compensate bias error (d) combination of TSK and linguistic context in the consequent part. Finally, we contrast the performance of the enhanced models with other fuzzy models for automobile MPG predication data and coagulant dosing process in a water purification plant.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.12
• /
• pp.1870-1877
• /
• 1990

The electromagnetic properties of P- and n-channel split drain magnetic sensitive MOSFET fabricated using 2\ulcorner design rules and CMOS process technology has been investigated. The achieved output voltage in the double drain MOSFET was 160mV at 10\ulcorner drain current and magnetic flux density of 10kG, and the sensitivity was 1.6x10**3 V/A\ulcornerG. A further higher sensitivity was obtained by introducing a third drain in the split region. In this case, the triple drain MOSFET showed a much higher sensitivity of 2x10**3 V/A\ulcornerG under the same condition. Also, the linearity of output voltage vs. magnetic flux density was excellent.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.848-849
• /
• 2015

This paper presents the structure design for optimizing output power density and efficiency to develop a spoke-type interior permanent magnet synchronous generator (IPMSG). To obtain the optimal structure, the combination of response surface method (RSM) and 2-D finite element analysis can solve the problem effectively for reducing the volume of permanent magnets (PMs) and maximizing the ratio between power density and efficiency. The effectiveness of this proposed structure design is verified by the simulation and experiment according to the comparison of the electromagnetic characteristics between the initial and modified structure.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.6
• /
• pp.814-822
• /
• 1986

Flow patterns and its transitions in vertical two phase flow of air-water isothermal flow are identified objectively by void output signals and moments computed from the Probability Density Function which is associated with the statistical measurement for time average local void fractions using conductance probe. It has been shown that the probe output signals, PDF distributions and its moments are deterministic criteria of flow pattern and transition classification.

• Proceedings of the Safety Management and Science Conference
• /
• 2003.11a
• /
• pp.335-343
• /
• 2003

In the electrode fabrication of unit cell, it was ascertained that electrochemical characteristics were greatly increased with 90 wt.% of BP-20, 5 wt.% of Super P and 5 wt.% of mixed binder [P(VdF-co-HFP) : PVP =7 : 3] The self-discharge of unit cell showed that diffusion process was controlled by the ion concentration difference of initial electrolyte due to the characteristics of Electric Double Layer Capacitor (EDLC) charged by ion adsorption in the beginning, but this by current leakage through the double-layer at the electrode/electrolyte interface had a minor effect and voltages of curves were remained constant regardless of electrode material. The electrochemical characteristics of 2.3 V/3,000 F grade EDLC were as follows: 0.35 m of DC-ESR (100 A discharge), 0.14 mof AC-ESR (AC amplitude 100 mV), 2.80 Wh/kg (3.73 Wh/L) of energy density and 4.64 kW /kg (6.19 kW/L) of power density. Power output was compatible with electric vehicle applications, uninterrupted power supply and engine starter, in due consideration of Ragone relations.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.12
• /
• pp.1310-1316
• /
• 2008

Bi-layer and tri-layer structures of electro-active paper(EAPap) using conductive polyaniline(PANI) coating were investigated to improve bending displacement of cellulose EAPap. Two different counter ions, perchlorate($CIO_4^-$) and tetrafluoroborate($BF_4^-$), are used as dopant ions in the PANI processing. The actuation performances of hi-layer and tri-layer structure are evaluated in terms of tip displacement, blocked force, strain energy density and power output density. The actuation performance of the tri-layer actuator was better than the hi-layer structure, and the maximum displacement and blocked force of tri-layer $CIO_4^-$ doped-PANI-EAPap were 13.2 mm and 0.15 mN, respectively. Also the power output of the actuator is similar to the required power of biological muscle application.