• JSTS:Journal of Semiconductor Technology and Science
• /
• 제3권4호
• /
• pp.181-187
• /
• 2003

This paper presents an 125MHz, 128-phase phase-locked loop using interpolation technique for digital timing recovery. To reduce the power consumption and chip area, phase interpolation was performed over only selected windows, instead of overall period. Four clocks were used for phase interpolation to avoid the output jitter increase due to the interpolation clock (clock used for phase interpolation) switching. Also, the output clock was fed back to finite-state machine (FSM) where the multiplexer selection signals are generated to eliminate the possible output glitches. The PLL implemented in a $0.25\mu\textrm{m}$ CMOS process and dissipates 80mW at 2.5V supply and occupies $0.84\textrm{mm}^2.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.498-500
• /
• 2012

According to the climatic characteristics of the wind power output is difficult to predict and a severe strain due to a change in output has been very influential in the grid. Jeju Hangwon wind farm, many of the wind generator is installed in a wide area because it is not have this device that artificially Smoothing is needed. In addition, By the requirements of the power company active power supply / control and improve power system reliability and energy storage during the peak demand for electricity using the energy stored in the power supply is needed. In this paper, Unit 12 in Jeju Hangwon demonstrated 0.5MW PCS and energy storage system associated with the wind through the stabilization of output and the leveling of output and test results will be introduced.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.49-52
• /
• 2009

Practical building integrated photovoltaic system built by Kolon E&C has been monitored and evaluated with respect to power generation, which was installed in Deokpyeong Eco Service Area in Deokpyeong, Gyeonggi, Korea. The amorphous silicon transparent PV module in this BIPV system has 44Wp in power output per unit module and 10% of transmittance with the unit dimension with $980mm{\times}950mm$. The BIPV system was applied as the skylight in the main entrance of the building. This study provided the database for the practical application of the transparent thin-film PV module for BIPV system through 11 month monitoring as well as various statistical analyses such as monthly power output and insolation. Average monthly power output of the system was 52.9kWh/kWp/month which is a 60% of power output of the previously reported data obtained under $30^{\circ}$of an inclined PV module facing south(azimuth=0). This lower power output can be explained by the installation condition of the building facing east, west and south, which was resulted from the influence of azimuth.

• 한국정보전자통신기술학회논문지
• /
• 제7권1호
• /
• pp.36-39
• /
• 2014

폐수 속에 들어있는 미생물을 이용해서 전기를 얻을 수 있도록 고안된 것이 미생물 연료전지이다. 본 논문에서는 미생물 연료전지의 전극 재료와 구조에 따른 전기적 특성을 조사했다. 구리판을 캐소드 전극으로 사용한 연료전지는 구리판의 산화 반응에 따른 전압역전현상이 관찰되어 백금판을 전극으로 사용한 연료전지보다 낮은 출력 전압을 나타내었다. 구리판을 전극으로 사용한 경우 전극판의 간격이 작을수록 높은 전압특성을 나타내었고 면적이 넓을수록 최고출력전압이 나타나는 시간이 지연되는 특성을 보였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권6호
• /
• pp.777-788
• /
• 2014

This paper presents a wide output range, high power efficiency reconfigurable charge pump for driving touch panels with the high resistances. The charge pump is composed of 4-stages and its configuration automatically changes based on the required output voltage level. In order to keep the power efficiency over the wide output voltage range, internal blocks are automatically activated or deactivated by the clock driver in the reconfigurable charge pump minimizing the switching power loss due to the On and Off operations of MOSFET. In addition, the leakage current paths in each mode are blocked to compensate for the variation of power efficiency with respect to the wide output voltage range. This chip is fabricated using $0.18{\mu}m$ BCD process with high power MOSFET options, and the die area is $1870{\mu}m{\times}1430{\mu}m$. The power consumption of the charge pump itself is 79.13 mW when the output power is 415.45 mW at the high voltage mode, while it is 20.097 mW when the output power is 89.903 mW at the low voltage mode. The measured maximum power efficiency is 84.01 %, when the output voltage is from 7.43 V to 12.23 V.

• 대한안전경영과학회지
• /
• 제9권2호
• /
• pp.183-194
• /
• 2007

1. Through this experiment, we made certain that the best distinguished frequency area of the Hyundae Beta 2.0 engine's knocking is 6.8khz. 2. Through the experiment, we checked the output power voltage condition of the logging output with the generation of a engine knocking. And wechecked up that it generated maximumly up to 11.4 V which depends on the degree of the streng.

• 한국전기전자재료학회논문지
• /
• 제36권2호
• /
• pp.136-142
• /
• 2023

In the past, the efficiency of solar cells had been increased in order to increase the efficiency of solar modules. However, in recent years, in order to increase output in the solar industry and market, the competitiveness of solar cells based on large-area solar cells and multi-bus bar has been increasing. Multi-busbar solar module is a technology to reduce power loss by increasing the number and width of the front busbar of the solar cell and reducing the current value delivered by the busbar by half through half-cutting. In the case of the existing M2 (156.75×156.75 mm²) solar cell, even with a half-cut, power loss could be sufficiently reduced, but as the area of the solar cell is enlarged to more than M6 (166×166 mm²), the need for more divisions emerged. This affected not only solar cells but also inverters required for module array configuration. Therefore, in this study, the electrical characteristics of a large-area solar cell and after division were extracted using Griddler simulation. The output characteristics of the module were predicted by applying the solar cell parameters after division to PSPice, and a guideline for the large-area solar module design was presented according to the number of divisions of the large-area solar cell.

• 동굴
• /
• 제77호
• /
• pp.1-7
• /
• 2007

Nowaday, prohibition of smoking is getting more important issue. So we designed "non-smoking area control system". This system is organized with AVR(ATmega8535), smoke sensor, comparator(LM339) and etc. In non-smoking condition sensor's output voltage is about 5V, and in smoking condition sensor's output voltage is under 5V. So we used comparator(LM339) to devide two conditions. In both conditions AVR(ATmega8535) transmits datas to the computer of administrator. At this time method of communication is RS-232.

• 대한전기학회논문지
• /
• 제41권9호
• /
• pp.1085-1094
• /
• 1992

A variable-spacing cesium thermionic energy conversion test station is designed and fabricated for the study of power generation. The diode is in the form of a guard-ringed plane-parallel geometry in which a polycrystalline rhenium emitter of 2 cmS02T area faces a radiation-cooled polycrystalline rhenium collector of 1.9 cmS02T area. The emission of plasma from heated refractory electrode metal is the driving reaction in the direct conversion of heat to electricity by thermionic energy conversion. The plasma is produced from electrons and positive ions formed simultaneously by thermionic emission and surface ionization of cesium atoms incident on the hot emitter from the cesium vapor in the diode. And high plasma density causes plasma multiplication within the gap due to volume ionization that results in high power output. The variation of the saturation current of a Knudsen converter is investigated at an emitter-collector gap of 0.1 mm and an emitter temperatures. A maximum power output of 13.47 watta/cmS02T is observed at a collector temperature of 963 K and a cesium reservoir temperature of 603 K.

• 전기학회논문지P
• /
• 제55권1호
• /
• pp.31-34
• /
• 2006

A infrared rays sensor or ultrasonic sensor can detect the object at the narrow area, however a pressure sensor can detect man and animal at the wide area. It is necessary to manufacture the sensor by using Pb-free ceramics in the respect of environmental protection. Piezoelectric properties of ceramics added 0.2wt% $La_2O_3\;into\;0.96Bi_{0.5}(Na_{0.84}K_{0.16})_{0.5}+0.04SrTiO_3$ were 0.4 of kp, $31{\times}$10^{-3}Vm/N\;of\;g_{33}$. The output voltage of the pressure sensor is 0.48 V at 20 in$H_2O$. The output voltage of the pressure sensor with driving circuit is 9.8 V, 37 ms width.