• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.864-867
• /
• 2003

GPS (Global Positioning System) made by the Department of Defense in U.S.A is positioning system to use satellite and initially it has been used only for the military forces but open to civilian in about 1987. This system has widely been used for not only surveying land, but also car navigation on the street and means to build up the data of the GIS. With GPS, recently our country is accelerating to make imbeded system and also the study on imbeded system is well under way. For example, Car navigation and the construction of the Seokang bridge between Willson Arch at Han river by using DGPS were evaluated as successful model to lead accurate location with the precision of the cm. The examples of the project performance with GPS has gradually been extended to the each department organization of the local and central government. for the example, It is true that BIS(Bus Information System) is widely spreading out. In addition, the study on the Distribution Maintenance System is expected to be well in progress to take advantage of GPS based on the data base of the NGIS(National Geography Institute System) of the NGI(National Geography Institute). This paper shows that we embodied not only the large imbeded system for car and finding the location in Korean Land Corporation but also the protype of the kinematics Wrist Held which is easily portable to pedestrian, climber and marathon runner.

• Journal of Wetlands Research
• /
• v.19 no.2
• /
• pp.193-201
• /
• 2017

This study was carried out to obtain basic ecological information required for wetland restoration in Korea where wetland is very deficient. To arrive at the objective, we collected the basic ecological information for wetland restoration in four Doombeongs located on Goesan of Chungcheongbuk-do (province), central Korea where maintains relatively integrate feature of Doombeong. Synthesized horizontal distribution of vegetation based on vegetation established naturally except that established by artificial interference, Potamogeton distinctus community, Spirodela polyrhiza community, Sagittaria aginashi community, Trapa japonica community, Scirpus triangulatus community, and Sparganium japonicum community, Persicaria thunbergii community, Juncus effusus var. decipiens community, Ludwigia prostrata community, Humulus japonicus community, Persicaria nodosa community, Miscanthus sacchariflorus community, Phragmites communis - P. japonica community, and Scirpus radicans community, S. gracilistyla community, Spiraea prunifolia for. simpliciflora community, and Rosa multiflora community, and Salix koreensis community and Acer tataricum subsp. ginnala community tended to be established in aquatic zone, herbaceous plant dominated vegetation zone, shrub dominated vegetation zone, and tree and sub-tree dominated vegetation zone, respectively. As the result of DCA ordination based on vegetation data collected from several Doombeongs and their surrounding areas, plant communities tended to be classified into aquatic, wetland, and riparian plant dominated stands. Spatial niche and species composition of major plant communities composing those stands were suggested as the reference information for creating ecological pond as a type of wetland. Further, the importance of wetland and the necessity of wetland restoration was discussed based on functions that the wetland displays.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.6
• /
• pp.474-481
• /
• 2011

The discharge coefficient and spatial velocity distribution were clarified by carrying out a physical experiment to assess the performance of sluice for tidal power generation. The physical experiment was performed by manufacturing 10 sluce models whose scale is 1/70 of the prototype and installing it in the planar open channel, which has apron sections in front of and behind the sluice models. In particular, it was attempted to reasonably determine the locations and method of measuring water levels that may affect estimation of the discharge coefficient. Based on the experimental results for various conditions of discharges and tidal levels, the discharge coefficient of the sluice in the experiment was estimated as 1.3 to 1.4. Meanwhile, it was found that velocities were 2~3% faster at the sluices near the central region whereas 4~5% slower at the sluices on both sides, in comparison to the average value of the mean velocities of the ten sluices.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.6
• /
• pp.332-349
• /
• 2016

OLAFOAM is the powerful CFD code and is an expanded version of $OpenFOAM^{(R)}$, for wave mechanics simulation. The $OpenFOAM^{(R)}$ does provide many solvers to correspond to each object of the numerical calculation in a variety of fields. OLAFOAM's governing equation bases on VARANS (Volume-Averaged Reynolds-Averaged Navier-Stokes) equation, and the finite volume method is applied to numerical techniques. The program is coded in C++ and run on the Linux operating system. First of all, in this study, OLAFOAM was validated for 1) wave transformation inside porous structure under bore and regular wave conditions, 2) wave transformation by submerged breakwater under regular wave condition, and 3) regular wave transformation and resultant vertical velocity distribution under current by comparison with existing laboratory measurements. Hereafter, this study, which is almost no examination carried out until now, analyzed closely variation characteristics of water surface level, wave height, frequency spectrum, breaking waves, averaged velocity and turbulent kinetic energy around porous submerged breakwater in the wave and current coexisting field for the case of permeable or impermeable rear beach. It was revealed that the wave height fluctuation according to current direction(following or opposing) was closely related to the turbulent kinetic energy, and others.

• Applied Chemistry for Engineering
• /
• v.8 no.6
• /
• pp.1006-1013
• /
• 1997

This study was carried out to elucidate the chemical characteristics of mutual separation for Am and Eu, which were selected as a stand-in from minor actinide and rare earth elements, by solvent extraction with di-(2-ethylhexyl)phosphoric acid containing zirconium at batch system. As results, 92.3% of Am and 99.1% of Eu were coextracted with 1M DEHPA/n-dodecane containing zirconium (Zr $concentration=8.7g/{\ell}$) at 0.5M $HNO_3$ in the extraction step. The extraction yields of Am and Eu were proportionally increased with the concentration of Zr in Zr salt of 1M DEHPA/n-dodecane having the synergistic effect. In the lst stripping step for the selective separation of Am, 38.1% of Am and 3% of Eu were stripped with the mixed solution of 0.05M DTPA and 1M lactic acid adjusted pH of 3.0. At that time, the separation factor calculated from the distribution coefficients of Am and Eu was 14.2. In the 2nd Stipping step to remove the Eu remained the organic phase after the lst stripping step, 94.4% 0f Eu was stripped into aqueous phase with 6M $HNO_3$.

• Journal of Sensor Science and Technology
• /
• v.8 no.2
• /
• pp.115-123
• /
• 1999

A micro-gas sensor with heater and sensing electrode on the same plane was fabricated on phosphosilicate glass(PSG, 800nm)/$Si_3N_4$ (150nm) dielectric membrane. PSG film was provided by atmospheric pressure chemical vapor deposition(APCVD), and $Si_3N_4$ film by low pressure chemical vapor deposition (LPCVD). Total area of the fabricated device was $3.78{\times}3.78mm^2$. The area of diaphragm was $1.5{\times}1.5mm^2$, and that of the sensing layer was $0.24{\times}0.24mm^2$. Finite-element simulation was employed to estimate temperature distribution for a square-shaped diaphragm. The power consumption of Pt heater was about 85mW at $350^{\circ}C$. Tin thin films were deposited on the silicon substrate by thermal evaporation at room temperature and $232^{\circ}C$, and tin oxide films($SnO_2$) were prepared by thermal oxidation of the metallic tin films at $650^{\circ}C$ for 3 hours in oxygen ambient. The film analyses were carried out by SEM and XRD techniques. Effects of humidity and ambient temperature on the resistance of the sensing layer were found to be negligible. The fabricated micro-gas sensor exhibited high sensitivity to butane gas.

• Journal of The Korean Association For Science Education
• /
• v.35 no.5
• /
• pp.919-929
• /
• 2015

This study aims to develop a modeling-based learning program about geologic structures and to reveal the relationship between the argumentation patterns and levels of students' mental models. Participants included 126 second grade high school students in four sessions of modeling-based learning regarding continental drift, oceanic ridges, transform faults, and characteristics of faults. A modeling-based learning program was implemented in two classes of the experimental group, and teacher-centered traditional classes were carried out for the other students in the comparison group. Science achievement scores and the distribution of students' mental models in experimental and comparison groups were quantitatively compared. The video-taped transcripts of five teams' argumentation were qualitatively analyzed based on the analytic framework developed in the study. The analytic framework for coding students' argumentation in the modeling-based learning was composed of five components of TAP and the corresponding components containing alternative concepts. The results suggest that the frequencies of causal two-dimensional model and cubic model were high in the experimental group, while the frequencies of simple two-dimensional model and simple cross sectional model were high in the comparison group. The higher the frequency of claims, an argumentation pattern was proven successful, and the level of mental model was higher. After the rebuttal was suggested, students observed the model again and claimed again according to new data. Therefore, the model could be confirmed as having a positive impact on students' argumentation process.

• Journal of the Korean Ceramic Society
• /
• v.41 no.11
• /
• pp.797-803
• /
• 2004

The heat generation tests of SiC and MO$_2$ samples by use of a microwave heating system were carried out and UO$_2$+5 wt% CeO$_2$ pellets were sintered in a microwave furnace in an oxidizing atmosphere, by taking into account the characteristics of the microwave heating obtained from the heat generation tests. The characteristics of pellets sintered in a microwave furnace were analysed and compared with those of the pellets sintered in a conventional electrical furnace. The temperature of MO$_2$ pellets with microwave heating increased quickly with input power and the variation of output power depended on the reaction characteristics of SiC and MO$_2$ with microwave. The sintered density of UO$_2$+5wt% CeO$_2$ pellets sintered in the microwave furnace was lower about 2% T.D. than that of the pellets sintered in an electrical furnace with sintering parameters. The microstructure of pellets sintered in microwave furnace has a broader pore distribution but has a larger grain size than that of the pellets sintered in the electrical furnace.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.4
• /
• pp.58-66
• /
• 1990

A series of test was performed measuring the failure strength and failure mode of Gr/Pi, $[0^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}]_s$ laminate containing a single pin loaded hole. The finite element method is applied to calculate the stress distribution in the laminates, then the failure load and the failure mode were predicted by means of the characteristic length. 12 different geometric variations were developed to analyze the effects of the ratio of specimen width to hole diameter (W/d) and ratio of edge distance to hole diameter (L/d). X-Ray of NDE methods were utilized in finding out the initial defects, damage and the fracture mechanism, and SEM(Scanning Electron Microscopes) was used the evaluation of the fracture mechanism and crack propagation around hole under tension pin loading. $[0^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}]_s$ laminate are found to be most sensitive to W/d but not so influenced by L/d. The failure mode and tensile strength predicted by the model show agreement with experiment data for pin loading bolted jointed test except range of $L/d{\leqq}3$.

• The Korean Journal of Ecology
• /
• v.28 no.1
• /
• pp.31-36
• /
• 2005

An important theme of this paper is to search for more genelalities of diversity and distribution pattern on the trampled plant communities in Daegu area. A total of 50 phytosociological releves were analyzed by the Zurich-Montpellier School's method and generalized habitat characteristics by using Euclidean coefficient and PCoA (Principal Coordinates Analysis). Five plant communities were classified and matched into largely two physiognomic types: grass-types such as Eragrostis ferruginea community, Eleusine indica community, Setaria viridis community, Digitaria ciliaris community, and forb-type of Plantage asiatica community only. These plant communities correspond to quite distinctive four habitat types, with both soil stability and moisture in microhabitat conditions: stable-moderate, unstable-moderate, stable-dry, and unstable-dry. Top-ten species showing the highest relative net contribution degree(r-NCD) were Digitaria ciliaris, Eleusine indica, Eragrostis ferruginea, Plantago asiatica, Echinochloa crus-galli, Trifolium repens, Polygonum aviculare, Setaria viridis, Setaria glauca and Artemisia princeps. The front three species showing more than 50% in percent r-NCD possess florescence after monsoon season. It is critically pointed out that the regional ecological differentiations i.e. the Daegu bioclimatic division, the $C_4$-plant dominant season(post-monsoon) of Korean peninsula, and species composition different from Japan's Plantaginetalia asiaticae, are the basis for deriving characteristics of the roadbed trampled plant communities of Daegu.