• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.37-42
• /
• 1997

Off-line feed rate scheduling is an advanced methodology to automatically determine optimum feed rates for the optimization of NC code. However, the present feed rate scheduling systems have lim~tations to generate the optimized NC codes because they use the material removal rate or non-generalized cutting force model. In this paper, a feed rate scheduling system based on an improved cutting force model that can predrct cutting forces exactly in general machining was presented. Original blocks of NC code were divided to small ones with the modified feed rates to adjust the peak value of cutting forces to a constant vale. The characteristic of acceleration and deceleration for a given machrne tool was considered when off-line feed rate scheduhng was performed. Software for the NC code optimization was developed and applied to pocket machining simulation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.421-428
• /
• 2004

Acoustic response control of a corner-pinned plate using piezoelectric wafers was studied, both theoretically and experimentally. Three different sizes of aluminum alloy plates were used and available ball joints were employed to hold the plate at the four corners. The plate with the largest aspect ratio showed the largest and most clear responses to the acoustic excitation in the range of frequencies (0～200Hz), and sound pressure levels (80～100dB) as predicted. The reduction of the acoustic response of the plate by piezoelectric actuator was very significant, more than expected, but abatement of the sound transmission through the plate was only slightly altered by the piezoelectric actuator. This work is an original work extending earlier work with doors excited by acoustic fields. The important difference is the used of ball joints to simulate the joints.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.42-45
• /
• 1997

Weldline movement of tailored blanks originates from two sources, primary and secondary. Primary movement occurs by geometrical reason, that is, just scratched lines on the no-weld blanks move during drawing to be fitted to geometrical change. Secondary movement is induced by the characteristics of tailored blanks itself. The primary movement was mainly dependent on the weldline location and not affected by the type of material. The secondary movement caused by laser welding and/or small strength difference in this study was not dominant compared with primary movement. The formability of tailored blanks always inferior to those of original blanks. This is due to the existence of hardened weld bead. The closer a weldline is to punch corner where drawing is most active, the worse its formability becomes. This is because the weldline prohibits the drawing process. It was confirmed by measuring diagonal length at the blank corner. The mode of fracture was changed form wall break to draw break when the weldling was close to the punch corner.

• Journal of the Korean Wood Science and Technology
• /
• 제42권5호
• /
• pp.516-522
• /
• 2014

Old architectural wood materials damaged by a fire were evaluated on the basis of wood species and scanning electron microscopy (SEM) observation of wood tissues in combination with energy dispersive X-ray spectroscopy (EDXS) analysis. Results of SEM observation showed that tracheid wall thickness of burned parts was very thin compared with undamaged and sound wood, and tylosoid in the resin canals disappeared after the exposure to fire. SEM-EDXS analysis indicated that carbon and oxygen peaks occurred in the original energy band, and the carbon peak was higher than that of the oxygen in the burned part. A computerized tomography was also undertaken to investigate the carbonization layer formed by fire and possible internal defects.

• Structural Monitoring and Maintenance
• /
• 제1권1호
• /
• pp.69-87
• /
• 2014

A new output only modal analysis method is developed in this paper. This method uses continuous wavelet transform to modify a popular blind source separation algorithm, second order blind identification (SOBI). The wavelet modified SOBI (WMSOBI) method replaces original time domain signal with selected time-frequency domain wavelet coefficients, which overcomes the shortcomings of SOBI. Both numerical and experimental studies on bridge models are carried out when there are limited number of sensors. Identified modal properties from WMSOBI are analyzed and compared with fast Fourier transform (FFT), SOBI and eigensystem realization algorithm (ERA). The comparison shows WMSOBI can identify as many results as FFT and ERA. Further case study of structural health monitoring (SHM) on an arch bridge verifies the capability to detect damages by combining WMSOBI with incomplete flexibility difference method.

• Structural Engineering and Mechanics
• /
• 제65권4호
• /
• pp.477-490
• /
• 2018

Reinforced concrete (RC) columns, as the primary load-bearing structural components in buildings, may need to be strengthened due to material deteriorations, changes in usage, new building codes or new design requirements. The use of post compressed plates (PCP) to strengthen existing RC columns has been proven experimentally and practically to be effective in solving stress-lagging effects between the original column and the new strengthening jacket caused by the pre-existing loads. This paper presents a comprehensive summary and review of PCP strengthening techniques to strengthen preloaded RC columns. The failure mode, deformability, and ductility of the strengthened RC columns are reviewed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권6호
• /
• pp.800-808
• /
• 1998

In this study the thermal stress distribution and deformantion characteristics resulting from the nonuniform temperature fields of the cylinder block of a light 3-cylinder 4-stroke gasoline engine were analyzed using the 3-dimensional finite element method. The temperature distributions req-uisite for the thermoelastic behavior alalysis were obtained from the steady-state heat conduction analysis performed on the basis of experimental data. in order to examine the effect of a ceramic material the cylinder liner was replaced by the silicon nitride($Si_{3}N_{4}$) and its thermal behaviors were compared with those of the original block.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.433-438
• /
• 2004

The rapid machining of prototypes plays an important role in product process. Rapid Prototyping(RP) is the widespread technology to produce prototype. But, it have many problems such as shrinkage, deformation and formation occurred by hardening of resin and stair shaping, On the contrary, high speed machining(HSM) technology has many advantages such as good quality, low cost and rapid machining time. Moreover, it is possible to use the material of original product. This paper presents manufacture of trial product by HSM and optimization of machining condition for high productivity in the view of manufacturing time and average error. For example, propeller is machined by the surface machining of thin surface parts. Experiments are designed of machining conditions by Latin Square method and machining condition is optimized and selected by ANOVA

• 대한기계학회논문집A
• /
• 제25권2호
• /
• pp.235-241
• /
• 2001

A crack with electrically conducting surfaces in a linear electrostrictive ceramic subjected to uniform electric fields is analyzed. Complete forms of electric fields and elastic fields for the crack are derived by using the complex function theory. The linear electromechanical theory predicts overlapping of the traction free crack surfaces. It is shown that the surfaces of the crack are contact near the crack tip. The contact zone size obtained on the basis of the linear dielectric theory for the conducting crack does not depend on the electric fields and depends on only the original crack and the material property for the linear electrostrictive ceramic.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.517-522
• /
• 2001

The purpose of this study is to investigate the thermal embrittlement and the mechanical properties of 2.25Cr-1Mo steel aged at high temperature and stress for 250 hours. Original, aged artificially material were tested to obtain the hardness and impact absorbed energy. Hardness and impact absorbed energy decreased with the increasing aging time. The carbide morphology with the thermal embrittlement was found to contribute to the mechanical property change by X-Ray diffraction method.