• Journal of environmental and Sanitary engineering
• /
• v.17 no.2
• /
• pp.26-33
• /
• 2002

Ultimate objective of industrial hygiene is the prevention of health impairment that may result from exposure to chemicals at workplace. Workers in solvent thinner-using occupation environment may be highly exposed to VOCs (volatile organic compounds) because solvent thinner has been used extensively such as painting, spraying, degreasing, coating and so on in Korea. The purpose of this study was to recognize, evaluate, and propose the control methods of VOCs from solvent thinner-using workplace. Five target volatile organic compounds (benzene, toluene, ethylbenzene, o-xylene, and m-xylene) were monitored in H company of Shiwa Industrial Complex and analyzed in perosnal, occupational indoor and outdoor during working hours simultaneously. Engineering control such as local ventilation should be made in considering the long-term exposure, though measured VOCs concentration did not exceed the workplace exposure standards. In addition, air cleaning device should be installed in local ventilation because Shiwa Industrial Complex has had the serious ambient air pollution. Currently, environmental purification using $TiO_2$ photocatalyst have attracted a great deal of attention with increasing number of recent environmental problems. In this study, $TiO_2$ sol coated on the ceramic bead was prepared by sol-gel method and the photodegradation of target compounds was investigated in gas phase by the exposure to UV-A lamp(365nm) in a batch system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.1
• /
• pp.216-224
• /
• 2001

HNS(hexanitrostilbene), one of the most important heat resistant explosive was recrystallized using organic solvent, nitric acid and dual solvent system of acetonitrile-toluene. The purification, analysis, type conversion method and its physical properties are described.

• KSBB Journal
• /
• v.15 no.3
• /
• pp.293-298
• /
• 2000

${\beta}$-Glucan a kind of polysaccharide which is particularly abundant in Agaricus blazei is known as the bioactive materials especially anticancer agents. The process development of the isolation and the purification process of water soluble ${\beta}$-glucans from A. blazei was achieved. and the process operation variables were optimized. Crude polysaccharides (CR.PS) were obtained from A. blazei by hot water extraction filtration solvent precipitation dialysis and freeze drying. Neutral and acidic fraction of polysaccharides were separated from crude polysaccharides by ion chromatography and then high molecular weight and low molecular weight fraction were separated from neutral fraction by gel chromatography. Quantitative and qualitative analysis of each compounds were performed with FT-IR NMR spectroscopy. Based on these analysis the optimal conditions of temperatures operating time organic solvent volume for precipitation and dialysis time were determined.

• Journal of the Korean Chemical Society
• /
• v.55 no.6
• /
• pp.936-939
• /
• 2011

Thiamine hydrochloride (VB1) has been used as an acid catalyst in organic synthesis. One pot three component Biginelli condensation of dimedone, urea/thiourea and substituted aromatic aldehydes catalyzed by 10 mol % of thiamine hydrochloride (VB1) in solvent free condition under microwave irradiation in good to excellent yields has been investigated. Utilization of microwave irradiation, simple reaction conditions, short reaction time, ease of product isolation, and purification makes this manipulation very interesting from an economic and environmental perspective.

• Composites Research
• /
• v.35 no.1
• /
• pp.23-30
• /
• 2022

Polycarbosilane(PCS) is an important precursor for melt-spinning the silicon carbide(SiC) fibers and manufacturing ceramics. The PCS is a metal-organic polymer precursor capable of producing continuous SiC fibers having excellent performance such as high-temperature resistance and oxidation resistance. The SiC fibers are manufactured through melt-spinning, stabilization, and heat treatment processes using the PCS manufactured by synthesis, purification, and control of the molecular structure. In this paper, we analyzed the effect of purification of unreacted substances and low molecular weight through solvent treatment of PCS and the effect of heat treatment at various temperatures change the polymerization and network rearrangement of PCS. Especially, we investigated the complex viscosity and structural arrangement of PCS precursors according to solvent treatment and heat treatment through the rheological properties.

• Korean Chemical Engineering Research
• /
• v.52 no.4
• /
• pp.497-502
• /
• 2014

Biomass-derived tar and waxy compounds have a highly negative effect on the separation and purification of paclitaxel and should be removed prior to final purification. Adsorbent treatment is a simple, efficient method for removal of tar and waxy compounds from plant cell cultures. In this study, we optimized the important process parameters (adsorption temperature, time, solvent type and adsorbent amount) of adsorbent treatment with Sylopute to remove the tar and waxy compounds in a pre-purification step. The optimal adsorption temperature, adsorption time, solvent type, and crude extract/Sylopute ratio were $30^{\circ}C$, 15 min, methylene chloride, and 1:1(w/w), respectively. This result could be confirmed by HPLC analysis of the absorbent after treatment and TGA of the organic substances that were bound to the adsorbent. In adsorbent treatment step, the purity seemed to show a small improvement but this treatment had a significant effect on convenience and feasibility of following steps by the removal of tar and waxy compounds.

• 한국생물공학회:학술대회논문집
• /
• 2002.04a
• /
• pp.504-507
• /
• 2002

A separation/purification process for enzymatic sugar ester production was investigated The crude reaction mixture contained sugar ester and unreacted fatty acid in acetone. The reaction mixture was mixed with KOH/phosphate buffer. Hexane was then added to enhance phase separation. Three phases formed: a lower aqueous phase containing nothing of interest, a polar organic solvent middle phase that contained mostly fatty acid soaps, and a hexane-rich upper phase that contained mostly sugar ester. Distribution coefficient of each component was measured.

• Resources Recycling
• /
• v.1 no.1
• /
• pp.58-68
• /
• 1992

A process development for direct synthesis of high pure ZnO powders from zinc-bearing waste was investigated. This waste contains a 55% of zinc and it was extracted by the sulfuric acid(leaching). After removal of iron ion by precipitation from the zinc solution, the purification through a solvent extraction by the use of D2EHPA as an extractant was carried out. Then, loaded zinc in organic solution was stripped and precipitated simultaneously using a precipitant such as oxalic acid. Then, loaded zinc in organic solution was stripped and precipitated simulataneously using a precipitant such as oxalic acid. The synthesized $ZnC_2O_4$ powders by the precipitation stripping method was calcined to obtain more than 99.9% of ZnO powders. The effect of sulfuric acid concentration, leaching time, pulp density on the extraction of zinc was studied and the optimum conditions for the solvent extraction were obtained through the investigation of purification of zinc solution. The size, morphology and size distribution of synthesized $ZnC_2O_4$ powders were studied in terms of oxalic acid concentration, temperature, surfactant added, precipitation time, etc.

• Applied Chemistry for Engineering
• /
• v.21 no.6
• /
• pp.616-620
• /
• 2010

This study was performed to recycle Propylene Glycol Monomethyl Ether Acetate (PGMEA) from Liquid Crystal Display (LCD) industry emission as a waste organic solvent by using a multistage distillation column and tried to decide optimum reflux ratio. From the final experiment result, it was confirmed ; in case the sample A, the PGMEA purity is more than 98% and the moisture is less than 0.05%, on the other hand, in case the sample B, the PGMEA purity is more than 95% when the reflux ratio is 6 and the moisture is less than 0.01% (Refer to Table 1 for the contents of sample A and B). These values means fine level which can be adapted in the LCD manufacture, requiring more than 90% common purity of recycling level.

• Clean Technology
• /
• v.27 no.2
• /
• pp.132-138
• /
• 2021

Research is being conducted on graphene to provide graphene having both excellent physical as well as electrical properties in addition to unique physical properties. In this study, Hummer's method, which is a representative method for chemical exfoliation, was applied in order to investigate the possibility of the mass production of high-quality graphene oxide. Three types of graphite (graphite, crystalline graphite, and expanded graphite) were used in the preparation of graphene oxide with variations in the amount of potassium permanganate added, reaction temperature, and reaction time. Then a Fourier transform infrared spectroscopy (FT-IR), a Raman spectrometer, and a transmission electron microscope (TEM) were used to measure the quality of the prepared graphene oxide. Of the three types of graphite used in this experiment, crystalline graphite showed the highest quality. The prepared graphene oxide was then purified with an organic solvent, and an analysis conducted using energy dispersive X-ray spectroscopy (EDS). From the results of the residual values, we were able to confirm that both acid wastewater and wastewater were best purified using cyclohexane. The method for manufacturing graphene oxide as well as the method of purification using organic solvents that are presented in this study are expected to have less of an environmental impact, making them environmentally friendly. This makes them suitable for use in various industrial fields such as the film industry and for heat dissipation and as coating agents.