• Bulletin of the Korean Chemical Society
• /
• v.35 no.5
• /
• pp.1491-1494
• /
• 2014

High-crystallinity poly(3-hexylthiophene) (P3HT) thin films were prepared by aging the precursor solutions, prepared using a good solvent, chloroform, at low temperatures prior to spin-casting. Lower solution temperatures significantly improved the molecular ordering in the spin-cast P3HT films and, therefore, the electrical properties of field-effect transistors prepared using these films. Solution cooling enhanced the electrical properties by shifting the P3HT configuration equilibrium away from random coils and toward more ordered aggregates. At room temperature, the P3HT molecules were completely solvated in chloroform and adopted a random coil conformation. Upon cooling, however, the chloroform poorly solvated the P3HT molecules, favoring the formation of ordered P3HT aggregates, which then yielded more highly crystalline molecular ordering in the P3HT thin films produced from the solution.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.411-419
• /
• 1993

A process for the preparation of cobalt oxide powders was developed by the evaporaton of emulsion containing cobalt. The characteristics of powders were examined by means of DTA, X-ray diffracton, SEM, PSA. Cobalt oxide powders were produced by evaporating the emulsion prepared by mixing cobalt sulfate solution and organic phase consisted of kerosene, Span 80 and D2EHPA in the kerosene bath at 16$0^{\circ}C$, then the precursor obtained was calcined at 100$0^{\circ}C$. As the concentration of cobalt ions in the aqueous solution, Span 80 and the stirring speed increased, the mean size of cobalt oxide powders decreased and the size distribution was improved. At the volume ratio of one of the aqueous to organic phase, the finest mean size and the optimum size distribution was obtained. On the other hand the concentration of D2EHPA and liquid paraffin had little effect on the mean size as well as on the size distribution of powders.

• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.255-260
• /
• 2000

We report that the crack-free organic-inorganic hybrid silica thin films were fabricated by sol-gel process using organometallic compounds as a precursor and that we have established very reproducible fabrication condition with systematic investigation of thickness and refractive index variations for various control parameters, such as, coating type, coating speed, chemical composition, prebake and postbake temperature. Additionally, we measured and compared the change of optical property with the UV exposure dose for three different kinds of photoinitiators. Furthermore, the fabrication of Ix4 MMI optical power splitter using the sol-gel thin film provides the possibility of various applications to the optical waveguide devices. vices.

• Carbon letters
• /
• v.16 no.3
• /
• pp.219-221
• /
• 2015

In order to study the impact of atmosphere during electron beam irradiation (EBI) of polyacrylonitrile (PAN) precursor fibers, the latter were stabilized by EBI in both air and oxygen atmospheres. Gel-fraction determination indicated that EBI-stabilization under an oxygen atmosphere leads to an enhanced cyclization in the PAN fibers. In the Fourier-transform infrared spectroscopy analysis, the PAN fibers stabilized by EBI under an oxygen atmosphere exhibited a greater decrease in the peak intensity at 2244 cm⁻¹ (C≡N vibration) and a greater increase in the peak intensity at 1628 cm⁻¹ (C=N absorption) than the corresponding PAN fibers stabilized under an air atmosphere. From the X-ray diffraction analysis it was found that oxygen uptake in PAN fibers leads to an increase in the amorphous region, produced by cyclization.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.7
• /
• pp.2139-2142
• /
• 2014

A one-pot, facile and ecofriendly approach to the fabrication of covalently fluorinated graphene using mild reaction conditions is reported. This straightforward and efficient strategy allows fluorine groups to be covalently and stably anchored onto graphene to produce single-layer functionalized graphene sheets from a graphene oxide precursor.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.750-753
• /
• 2002

The chemical vapor condensation process of Parylene-N thin films was investigated and applied to the passivation of the organic light emitting diodes (OLEDs). The effects of process variables on the deposition rate were studied, and it was found that the deposition rate of Parylene increases with increasing precursor sublimation temperature but decreases with increasing substrate temperature. The Parylene film was used as a passivation layer for OLEDs, and as a result, the lifetime of the passivated OLEDs was increased by a factor of about 2.3 compared with that of non-passivated OLEDs.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.7 no.1
• /
• pp.31-37
• /
• 2002

This paper was investigated to clarify the possibility of a biodegradation of materials adsorbed on different porous granular-activated carbons (GACs) such as coal-& coconut-based GAC. Total organic carbon, humic substance and ammonia were used to compare their removal efficiencies. The objective of this study is to determine the adsorption capacity of bioregenerated GAC. When raw water reacted with chloride, the yield of THMs increased as a function of the input amount of chloride. The formation of trihalomethanes (THMs) was investigated in water treated with chlorine when humic acid was used as THM precursor. As the input amount of chloride in raw water increased by two or five-fold to remove the $NH_3$, the chloroform of the THMs significantly increased also five or ten-fold. It was found that the chloroform was significantly removed by the treatment of biological activated carbon (BAG) in comparison with the ozone treatment, and the removal efficiency of THMs in coal-typed GAC was $10-30\%$ better than coconut-typed GAC due to the biological degradation on the surface of the activated carbons.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.6
• /
• pp.289-293
• /
• 2005

We have fabricated superconductor ceramics by chemical process. A high Tc superconductor with a nominal composition of $Bi_2Sr_2Ca_2Cu_3O_y$ was prepared by the organic metal salts method. Experimental results suggest that the intermediate phase formed before the formation of the superconductor phase may be the most important factor. The relation between electromagnetic properties of Bi HTS and external applied magnetic field was studied. The electrical resistance of the superconductor was increased by the application of the external magnetic field. But the increase in the electrical resistance continues even after the removal of the magnetic field. The reason is as follows; the magnetic flux due to the external magnetic field penetrates through the superconductor and the penetrated magnetic flux is trapped after the removal of the magnetic flux.

• Carbon letters
• /
• v.16 no.1
• /
• pp.11-18
• /
• 2015

The process of oxidizing polyacrylonitrile (PAN)-based carbon fibers converts them into an infusible and non-flammable state prior to carbonization. This represents one of the most important stages in determining the mechanical properties of the final carbon fibers, but the most commonly used methods, such as thermal treatment ($200^{\circ}C$ to $300^{\circ}C$), tend to waste a great deal of process time, money, and energy. There is therefore a need to develop more advanced oxidation methods for PAN precursor fibers. In this review, we assess the viability of electron beam, gamma-ray, ultra-violet, and plasma treatments with a view to advancing these areas of research and their industrial application.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.8
• /
• pp.1491-1494
• /
• 2008

A novel platinum aminoalkoxide complex, Pt$(dmamp)_2$ has been prepared by the reaction of cis-$(py)_2PtI_2$ with two equivalents of Na(dmamp) (dmamp = 1-dimethylamino-2-methyl-2-propanolate). Single-crystal X-ray crystallographic analysis shows that the Pt(dmamp)2 complex keeps a square planar geometry with each two nitrogen atoms and two oxygen atoms having trans configuration. Platinum films have been deposited on TaN/ Ta/Si substrates by metal organic chemical vapor deposition (MOCVD) using Pt$(dmamp)_2$. As-deposited platinum thin films did not contain any appreciable amounts of impurities except a little carbon. As the deposition temperature was increased, the films resistivity and deposition rate increased. The electrical resistivity (13.6 $\mu\Omega$cm) of Pt film deposited at 400 ${^{\circ}C}$ is a little higher than the bulk value (10.5 $\mu\Omega$cm) at 293 K. The chemical composition, crystalline structure, and morphology of the deposited films were investigated by X-ray photoelectron spectroscopy, X-ray diffraction, and atomic force microscopy.