• 한국환경과학회지
• /
• 제11권9호
• /
• pp.955-960
• /
• 2002

The recycled washwater, which has different water quality and is produced about 5 to 20% of the total water volume treated, affects the unit operation of water treatment, especially coagulation process. However, the effects of recycled washwater on unit operation of water treatment have not been fully investigated. In this study, effects of recycled washwater on coagulation process were investigated to find the optimum coagulation condition by analyzing turbidity, $UV_{254}$, TOC removal efficiencies. In addition, effects of recycled washwater on residual Al after coagulation were studied by analyzing soluble and particulate Al. The size distribution and fractal dimension of coagulated also analyzed. The recycled washwater was lower pH than the raw water. And the recycled washwater had higher $UV_{254}$, TOC and residual Al concentration than the raw water. Residual Al concentration of recycled washwater was about 50 times higher than that of raw water. Optimum coagulant dosages on the blending recycled washwater and the raw water for turbidity, $UV_{254}$ and Al removal were lower than that on the raw water. However, TOC removal increased by increasing coagulant dosage. The size and fractal dimension of coagulated particle produced in the blending recycled washwater were larger, which imply faster settling velocity, than those produced in the raw water only.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권2호
• /
• pp.157-165
• /
• 1997

The strength level of welded joint in room temperature and elevated temperature up to $600^{\circ}C$ was investigated in 250 and 300 grade 18% Ni maraging steel sheet welded with electron beam. The results obtained in this study are as follows; 1. Optimum welding heat input was 600J/cm in 1.0mm thickness and the room temperature tensile strength, joint efficiency of welded joint treated with optimum aging condition were found to be about 166kg/$mm^2$, 95% in 250 grade, 189kg/$mm^2$, 92% in 300 grade maraging steel sheet, respectively. 2. Tensile strength of welded joint in room temperature increased slightly by aging after repeated solution heat treatment, but the fracture mode showed a shear. 3. Joint efficiency at a temperature between $540^{\circ}C$and $600^{\circ}C$ found to be about 72% to 55%, but the joint efficiency exceeded about 90% below $300^{\circ}C$. 4. The fracture occurred in most weld metal, and the fracture surface showed a shallow dimple.

• 한국자원식물학회지
• /
• 제19권2호
• /
• pp.374-380
• /
• 2006

양치식물인 참쇠고비에서 인위적인 돌연변이를 유기하기 위하여, 기내배양한 근경조직에 EMS, NMU 등의 화학돌연변이원과 colchicine을 처리하였다. 식물체 재생률을 근거할 때, EMS의 적정 처리농도는 $20{\sim}50mM$이었으며, NMU는 $5{\sim}10mM$인 것으로 확인되었다. 또한 참쇠고비에서 엽의 색소 및 형태적 변이를 유도하는 데 있어 NMU가 EMS보다 효과적인 것으로 확인되었다. 표현형 변이 식물체의 유전적 변이를 분석하기 위하여 RAPD를 수행한 결과, 두 개의 10-mer primer에서 야생종과 변이주 사이에 다형성 DNA 밴드 패턴이 나타났다.

• Journal of Welding and Joining
• /
• 제13권3호
• /
• pp.147-156
• /
• 1995

The change of microstructure in the bonded interlayer and tensile properties of joints were studied for liquid phase diffusion bonding using STS-310 and Incoloy-825 as base metal and base metal+B alloy as insert inetal. Main experimental results obtained in this study are as follows. 1) The optimum amount of B addition into the insert metal was found to be about 4mass%. 2) When isothermal solidification was completed, the microstructure in the bonded interlayer was the same with that of the base metal because of the grain boundary migration in the bonded interlayer. 3) All of the tensile specimen fractured at base metal and joints bonded at optimum condition exhibited tensile properties in excess of base metal requirements. 4) It was determined that fine car-borides and bordes such as M$_{23}$(C,B)$_{6}$, Cr$_{2}$B, and CrB in STS-310S and TiB in Incoloy-825 exist at the grain boundary around bonded interlayer. These precipitates almost disappeared after homogenizing treatment at 1373K for 86.4ks.s.

• 한국의류산업학회지
• /
• 제7권5호
• /
• pp.547-552
• /
• 2005

The study has objective in raising value of the gray color as a meaningful color suiting sentiments of modern people by expressing the gray color in various perspective utilizing natural dyes that is natural at the same time having aesthetic color tones. For example, the main ingredient used for coloring black and gray color is the pyrogallol tannin and the gray tone dye can be acquired by combining the tannin with iron. In order to find the suitable condition for processing tannin, UV-Vis part absorption spectrum of Gallapple pyrogallol tannin, dye ability based on temperature and time, reflection rate based on concentration, color changes based on acid treatment and alkali treatment, changes on surface based on concentration or metal mordant condition, and lightfastness were measured. Maximum absorption wavelength (${\lambda}_{max}$) of Gallapple tannin was at around 273 nm, while strong absorption was also observed at below 350 nm. Dye ability of Gallapple tannin is done more easily on silk rather than cellulose fibers such as cotton, while the optimum condition for dyeing was observed to be at $60^{\circ}C$, for 20 minutes. As a result of acid treatment, the color of dye material consist highly of gray tones and showed red tone after the alkali treatment. While it was observed that as dye concentration and metal mordant concentration increased the color changed at counter-clockwise direction on the Y-scale of Munsell's scale of colors. Lightfastness was more on a normal fading. I hope this study opens up possibilities towards presenting gray color expressed from tannin as color with diversity and aesthetic value. In future, comparative study between dye expressed from catechol tannin dye materials will be helpful.

• Composites Research
• /
• 제23권6호
• /
• pp.32-38
• /
• 2010

폴리아미드 직물과 NBR의 최적 접착특성을 나타낼 수 있는 조건을 검토하기 위해 대기압 플라즈마(APP) 처리 효과에 대한 실험적 연구를 하였다. 대기압 화염 플라즈마(APFP) 처리의 경우 주어진 계면조건에서 최적의 처리횟수는 2회였다. APFP 처리 횟수가 증가함에 따라 직물의 열변형은 더욱 심하였다. APFP 처리 직물을 강화한 복합재료의 접착강도는 접착제를 한번 혹은 두번 도포한 계면에 대해 플라즈마를 처리하지 않은 경우에 비해 약 35% 증가하였다. 접착제를 중복 도포하였을 때, APFP 처리 직물 강화한 복합재료의 접착에너지는 약 4배 증가하였다. APFP 처리에 의한 폴리아미드 직물의 표면 개질이 다른 형태의 APP 처리방식과 비교했을 때, 경제적이고 빠르며 고무와의 접착강도를 개선시킬 수 있는 방법이라고 판단된다.

• 한국작물학회지
• /
• 제58권1호
• /
• pp.67-70
• /
• 2013

This research study was to develop methods for inhibiting the germination of cotton seeds. Germination rates after heating treatment at $80^{\circ}C$ with 10, 20, 30, 40 min. were 9.3, 9.3, 5.3 and 1.3 percentage, respectively. Heat treatment over $85^{\circ}C$ with 10 min. caused no germination of cotton seeds. Germination was significantly reduced with gamma rays treatment more than 10,000 gy, while the treatment within 2,000-8,000 gy induced less effects. Microwave processing for 30 seconds and 60 seconds inhibit the germination of cotton seed under 8 and 0%, respectively. As a physical treatment, rollmill milling with 1.5, 2, 2.5 mm gap inhibited any germination of cotton seeds. The optimum gap of roll-mill for processing physical cracking was below 51% of the thickness of seed.

• 한국초지조사료학회지
• /
• 제11권2호
• /
• pp.137-142
• /
• 1991

For the constitution of forage cropping system including the double-cropping of corn, attention has been directed towards the early and short maturing varieties of corn such as Comet 80, Comet 85 and Linda as a component forage crop of forage cropping system. Four corn varieties, Comet 80, Comet 85, Linda and Suwon 19 were planted delayedly by each of 45, 55 and 65 days from the recommended sowing date of suwon 19. Under these condition, growth characteristics and late-sowing adaptability of 4 corn varieties were investigated, and the results are summarized as follows; 1. The variety of suwon 19 did not reach the stage of silking in the occasion of late sowing by 50 days from the optimum sowing time for mono cropping of suwon 19. However early varieties such as Comet 80, Comet 85 and Linda silked under the condition of 65 days-delayed sowing from the recommended sowing time of Suwon 19 for mono-cropping. 2. Early varieties of Comet 80, Comet 85 and Linda were so grown by approximately 92% in plant height, 66% in ear height, 88% in stem diameter and 81% in leaf number respectively compared to Suwon 19 at each of three delayed sowing time that exhibited the dwarfish appearance of canopy. 3. Days from sowing to silking decreased as the sowing time was delayed and the average days from sowing to silking in the sowing treatments of 55 days-delayed of Suwon 19, Comet 80, Comet 85 and Linda were 61, 46, 47 and 51 days, respectively. 4. The size of variations of plant height and ear height influenced by delayed-sowing time was comparatively larger in the varieties of Suwon 19 and Linda than in those of Comet 80 and Comet 85. 5. As sowing time was delayed from the optimum sowing time of Suwon 19 for mono-cropping, ear content decreased from 0% of Suwon 19 at 55 day-delayed sowing treatment to 3540% of Comet 80 and Comet 85 at 65 days-delayed sowing treatment.

• 펄프종이기술
• /
• 제37권3호
• /
• pp.66-73
• /
• 2005

This study was performed to understand the changes in wood extractives, mainly acetone extracts, in pine woods (Pinus densiflora and Pinus rigida) treated by three blue stain fungi (BSF) such as native BSF in Korea, Leptographium sp., screened Albino strain(BSFcs-1) and commercial Cartapip and fungicide, Wood guard. In addition their pulping and bleaching properties were investigated. BSF treatment has significantly reduced acetone extracts, $25.1{\sim}30.4%$ decreasing in red pine and $22.9{\sim}28.1%$ in pitch pine. Three week aging treatment showed about 20% decreasing in red pine and 19.3% in pitch pine. There were not so significant differences in extracts reduction among native BSF and Albino-type strains (Albino strain, BSFcs-1, and commercial Cartapip). But fungicide, Wood guard, treated wood showed relatively lower decreasing rates of extractives, 14% in red pine and 10.1% in pitch pine. Therefore it is understandable that the fungicide could protect the wood from blue stain fungi attack, but has no effect on its extractive reduction. Concerned to pulping properties of BSF and fungicide treated woods, red pine and pitch pine, optimum pulping condition was 20% active alkali, wood to liquor ratio 1 to 6, $170^{\circ}C$, and 2.5 hr. In the case of BSF woods, optimum pulping condition was same as the sound wood, $43.5{\sim}45%$ of pulp yields and $1.3{\sim}1.45%$ of rejects. Screened pulp yield of fungicide treated wood was lower than those of BSF treated woods. Rejects in pulps were higher in fungicide-treated wood than BSF treated woods. Bleaching pulp yields were ranged of 92 to 93.5%. BSF, Cartapip and fungicide treated woods resulted in lower brightness of $55{\sim}58%$, but Albino-type strain(BSFcs-1) $61.3{\sim}62.3%$, very similar to untreated one. Therefore bleaching chemicals could be saved in the processing of chemical pulping.

• 분석과학
• /
• 제5권1호
• /
• pp.1-5
• /
• 1992

Amberlite XAD 고분자수지 및 고분자수지 대체흡착제인 rice bran, rice straw 그리고 sawdust에 대한 petroleum oil의 흡착량을 최저 흡착조건에서 뱃치법으로 측정하여 조사하였다. Rice bran과 rice straw에 대한 petroleum oil의 흡착량은 XAD계열수지의 흡착량의 약 50% 정도로 흡착성이 우수하였다. 또한 이들 대체흡착제의 흡착능을 증대시키기 위한 탄화시간은 $200^{\circ}C$, 30분이 최적 조건이었다. Sawdust의 경우에는 30% MeOH 매질에서는 흡착성이 매우 약한 반면 0.5M NaCl 매질에서는 XAD수지 흡착능이 약 1/2에 도달하였다. Rice bran과 rice straw는 외관상의 구조차이와는 관계없이 비슷한 흡착능력을 보였다. 따라서 rice bran과 rice straw들은 XAD계열 수지에 대한 대체흡착제로 충분한 흡착능력을 가지고 있는 것으로 보인다.