• 대한조선학회 특별논문집
• /
• 대한조선학회 2011년도 특별논문집
• /
• pp.63-69
• /
• 2011

Exhaust gases of a vessel from a main engine, a diesel generator and an incinerator contain very harmful substances like soot, $SO_2$ and NOx. Careful design of funnel shape is required to prevent those harmful exhaust gases from influencing on accommodation and a fan room. Meanwhile, the exhaust gases are also hot enough to damage electronic devices like radar. Therefore the funnel design should be considered so that electronic devices are not directly exposed to the exhaust gas in the strong stern wind. This study may propose guidelines of optimum design criterion for the anti-thermal damage design of the electronic devices and anti-recirculating design of harmful exhaust gas near the accommodation. From CFD analyses, we can understand that the major factors affecting the exhaust gas dispersion are the large scale mixing by separation vortices and the sluggish flow in the recirculation region. We hope that the funnel flow analysis around ship's funnel is used for practical optimum funnel design to minimize the exhaust gas dispersion by adjusting the funnel shape, the position of the exhaust pipe, the shape of bulwark, the exhaust direction of air ventilated an engine room and the angle of the exhaust pipe.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.457-462
• /
• 1999

The purpose of this study is to design the requirements for the materials of stabilizing slurry and to determine the optimum slruuy mix design used in the underground wall of Inchon LNG #213 and 214 tank. After the materials and mix conditions of stabilizing slurry investigated and tested, we propose materials and optimum mix design according to testing items including funnel viscosity, we propose materials and optimum mix design according to testing items including funnel viscosity, fluid loss, cake thickness and specific gravity. As this results, we select optimum mix design that the upper limit ratio of bentonite is 2.0%, polymer is 0.1% considering the funnel viscosity and dispersion agent is 0.05% considering the fluid loss. Also we select all materials which are composed of GTC4 as bentonite, KSTP as polymer and Bentocryl as dispersion agent. All test results are satisfied our specifications for stabilizing slurry.

• KCI Concrete Journal
• /
• 제14권4호
• /
• pp.151-159
• /
• 2002

This study investigates experimentally the optimum mix proportion and design factors of the stabilizing liquid used for excavation of the massive and deep slurry wall in LNG in-ground tank before pouring concrete. Considering those site conditions, the stabilizing liquid used for excavation of slurry wall has to be satisfied with some requirements including specific gravity, fluid loss, cake thickness, funnel viscosity and sand content in order to construct the safe and qualified slurry wall. For this purpose, we select materials including bentonite, polymer and dispersion agent. After performing many tests for materials and mix design process, we propose the optimum mix proportion that the upper limit ratio of bentonite is $2.0\%$, polymer is $0.1\%$ considering the funnel viscosity and dispersion agent is $0.05\%$considering the fluid loss of the stabilizing liquid. Also, we select all materials which are consisted of GTC4 as bentonite, KSTP as polymer and Bentocryl 86 as dispersion agent. Based on the results of this study, the optimum mix proportion of the stabilizing liquid is applicable to excavate the deep and massive slurry wall in LNG in-ground tank successfully.

• 한국대기환경학회지
• /
• 제20권4호
• /
• pp.493-501
• /
• 2004

The principle of vortex tube and cyclone was introduced to enhance the treatment efficiency of waste air streams containing particulate matters, toluene, and others developed by Hangreen Tech, Ltd. and Hoseo Chemical and Industrial Technology R＆D Center. Adsorption, condensation, and/or coagulation could be induced at low temperature zone formed by vortex tube and Joule-Thomson expansion. The pressurized air was introduced at the tangential direction into the cyclone system applied with the coaxial funnel tube. Easily condensible vapors such as toluene. carbon dioxide, and water vapor were adsorbed enforcedly on coagulated or condensed materials which were formed as cores for coagulation or condensation by themselves. These types of coagulation or condensation rates were rapidly promoted as the diameter being growing up. The maximum removal efficiency for carbon dioxide and toluene was achieved to about 87 and 90 percent, respectively. The Joule-Thomson coefficients were increased with the pressure of air injected in the range of the relative humidities between 10% and 30%. An optimum value was observed within the range of the tested temperatures at a fixed pressure. In conclusion. it could be identified that the treatment efficiency would be depended on the pressure of the process air introduced and physical and chemical characteristics of waste air streams containing target materials for a designed system. The final design parameters should be decided depending upon the given system and target materials.

• 대한기계학회논문집A
• /
• 제27권3호
• /
• pp.381-386
• /
• 2003

Gradually engineering designers are determined based on computer simulations. Modeling of the computer simulation however is too expensive and time consuming in a complicate system. Thus, designers often use approximation models called metamodels, which represent approximately the relations between design and response variables. There arc general metamodels such as response surface model and kriging metamodel. Response surface model is easy to obtain and provides explicit function. but it is not suitable for highly nonlinear and large scaled problems. For complicate case, we may use kriging model that employs an interpolation scheme developed in the fields of spatial statistics and geostatistics. This class of into interpolating model has flexibility to model response data with multiple local extreme. In this study. metamodeling techniques are adopted to carry out the shape optimization of a funnel of Cathode Ray Tube. which finds the shape minimizing the local maximum principal stress Optimum designs using two metamodels are compared and proper metamodel is recommended based on this research.

• 한국터널지하공간학회 논문집
• /
• 제10권3호
• /
• pp.245-256
• /
• 2008

터널 주지보재의 하나인 강지보재는 굴착 후 숏크리트 또는 록볼트의 지보기능이 발휘되기까지 터널 굴착면의 안정을 도모하는데 매우 중요한 역할을 수행한다. 일반적으로 수평터널의 강지보재는 중력방향으로 설치되고 있으며 시공성 및 안정성 측면에서 모두 유리한 것으로 알려져 있다. 그러나 경사터널의 경우는 터널 벽면에 작용하는 주응력 방향과 중력방향이 서로 다르기 때문에 최적의 강지보재 설치방향은 수평터널에서의 중력방향과는 다를 수 있다. 본 연구에서는 수치해석 방법을 이용하여 경사터널 벽면에 작용하는 힘의 작용방향을 규명하였으며 그 방향이 최적의 강지보재 설치방향이 될 수 있다. 즉, 강지보재의 지보효율은 터널 변위가 발생하는 방향으로 저항하도록 설치하는 경우에 최대가 될 수 있다. 국내 터널설계기준에서 제안하고 있는 경사터널에서의 세 가지 강지보재 설치방향을 모델로 설정하여 단계별 해석을 통한 비교검토를 수행하였다. 연구결과 경사터널 벽면에서의 변위 발생각은 막장경사와 관계없이 모두 터널 굴착면에 수직한 방향과 유사한 각도로 발생하므로 경사터널에서의 강지보재는 터널 굴착면에 수직인 방향으로 설치하는 경우가 지보효율 측면에서 보다 유리한 것으로 검토되었다.