• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.993-998
• /
• 2002

watches, air bearings and printed circuit hoards (PCB). However, it is not easy to determine optimum cutting conditions since the micro drilling process is very sensitive to various disturbances. Also, undesirable characteristics to optimize the micro drilling are small signal-to-noise ratios, drill wandering motions and high aspect ratios. Thus, in this study, experimental design methods are applied to determine optimum cutting conditions. Suing the methods, three cutting parameters, fred, step and curving speed are optimized to minimize thrust forces. Obtained conditions are verified through required experimental works. As the results, it is shown that the experimental methods can be applied to micro drilling processes to determine Optimum Cutting Conditions.

• Journal of Welding and Joining
• /
• 제12권3호
• /
• pp.71-81
• /
• 1994

Laser cutting is experiencing a rising worldwide acceptance in the industry. Expert systems are necessary for the systematic arrangement and searching of experimental data existing in journal papers, job handbooks, etc.. This paper proposes an expert system for the selection of the appropriate laser cutting variables from the available database. Optimum cutting conditions according to the given cutting velocity were searched and qualitative comments which are difficult to be used as database variables were shown at each velocity using the binary and fuzzy inference. These comments could be informative to unskilled operators of the laser cutting process. Typical cutting conditions of the mild steel and stainless steel were included and the working range and quality variations were displayed graphically. The proposed algorithm was implemented in an IBM compatible personal computer as an expert system for CO$_{2}$ laser cutting to derive the optimum cutting conditions by using the turbo prolog.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.33-38
• /
• 1995

In this study, unsistered, pre-sintered and sintered low purity alumina ceramics were machined with various tools to clarify the machniability, the optimum tool materials and the optimum tool materials and the optimum cutting conditions. The maon conclusions obtained were as follows. (1) Machined withalloy steel tool, the machinabilty of te pre-sintered ceramics becomes better with the decrease of pre-sintering temperature, but that of unsintered ceramics(white body) was extremely poor. (2) In the case of carbide tool K01, the tool life in machining white body was the longest, and the machinabilty of pre-sintered ceramics becomes poorer with the increase of the pre-sintering temperature. (3) In the case of ceramic tool, the 10000-1100 .deg. C pre-sintered ceramics showed te best machinability within a certain cutting speed range. So far as dry machining, the above combination and conditions showed the highest productivity. (4) When the pre-sintered ceramics were wet machined withsintered diamond tool, the tool life becomes extremelylong, and higher cutting speed can be can be used than in the case offull-sintered ceramics. The productivity of wet cutting is much higher than that ofdry cutting.

• KSTLE International Journal
• /
• 제3권1호
• /
• pp.17-22
• /
• 2002

Roughing of tool steel in its hardened state represents a real challenge in the die and meld industry and process improvement depends on research of tool material, coating technique, and lubrication. However, roughing of hardened steels generates extreme heat and without coolant flooding, tool material cannot withstand the high temperature without choosing the right tools with proper coating. This research conducted milling tests using coated ball end mills to study effects of cutting conditions and geometric parameters of ball end mills on the machinability of hardened tool steel. KP4 steel and STD 11 heat treated steels were used in the dry cutting as the workpiece and TiAIN coated ball end mills with side relief angle of 12$^{\circ}$ was utilized in the cutting tests. Cutting forces, tool wear, and surface roughness were measured in the cutting tests. Results from the experiments showed that 85 m/min of cutting speed and 0.32 mm/rev of feed rate were optimum conditions for better surface finish during rough cutting and 0.26mm/rev with the same cutting speed are optimum conditions in the finish cutting.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.143-148
• /
• 1995

A study on the generation of optimum tool path for machining the concave parts is discussed. Above all, the various cutting factors and their relationships are considered. Then optimum tool path for concave parts is generated on these cutting variables and their relationships. It is difficult for existing CAD/CAM systems tomachine the concave parts. For cutting the part even the experienced craft must give many attentions and muchtime since it needs consideration of various cutting conditions and geometric properties. The optimum tool path for the concave part is generated onnot only geometric properties byut also cutting conditions. We choose, as variables, feed and cutting direction for productivity, diameter of tool and constant(stable) cutting force for machining accuracy. The results are verified through simulation of the index of performance and cutting force.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.28-33
• /
• 2004

At present, industry and researchers are looking for ways to reduce the use of lubricants because of ecological and economical reasons. Therefore, metal cutting is to move toward dry cutting or semi-dry cutting. This paper presents an investigation into MQL(Minimum Quantity Lubrication) machining with the objective of deriving the optimum cutting conditions for the turning process of SM45C. To reach these goals several finish turning experiments were carried out, varying cutting speed, feed rate and oil quantity, with MQL. The surface roughness results of tests were measured and the effects of cutting conditions were analyzed by the method of Analysis of Variance(ANOVA). From the experimental results and ANOVA, it is found that a better surface roughness can be obtained by decreasing oil quantity and feed rate.

• 한국공작기계학회논문집
• /
• 제15권4호
• /
• pp.83-91
• /
• 2006

At present, industry and researchers are looking for ways to reduce the use of lubricants because of ecological and economical reasons. Therefore, metal cutting is to move toward dry cutting or semi-dry cutting. One of the technologies is known as MQL(Minimum Quantity Lubrication) machining. This research presents an investigation into MQL machining with the objective of deriving the optimum cutting conditions for the turning process of SM4SC. To reach these goals several finish turning experiments were carried out, varying cutting speed, feed rate, oil quantity and so on, with MQL and flood coolant. The surface roughness and cutting force results of tests were measured and the effects of cutting conditions were analyzed by the method of Analysis of Variance(ANOVA). From the experimental results and ANOVA, this research proposed optimal cutting conditions to improve the machinability in MQL turning process.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 춘계학술대회 논문집
• /
• pp.41-46
• /
• 1996

In this study, unsintered and pre-sintered low purity alumina ceramics were machined with various tools to clarify the machinability, optimum tool materials and optimum cutting conditions. The main conclusions obtained were as follows. (1)In the case of dry cutting, the sintered diamond and natural diamond tools exhibit better performance in machining of the ceramic pre-sintered at lower temperature, and the tool lives of both tools in machining the ceramics pre-sintered at high temperature becomes extremely short. (2)The performance of CBN tool becomes better in dry machining of the ceramics pre-sintered at higher temperature. (3)When the pre-sintered ceramics were wet machined with sintered diamond, the tool life becomes considerably long, and higher cutting speed can be used than in the case of the CBN and ceramic tools, the tool lives becomes shorter at wet cutting than at dry cutting, especially exhibiting extremely short tool life in wet cutting with ceramic tool.

• 한국정밀공학회지
• /
• 제15권9호
• /
• pp.43-49
• /
• 1998

The deep hole drilling has an increasing demands because of its wide range applications and its good productivity. The BTA drills are capable of machining for having a large length to diameter ratio in single pass to higher degree of accuracy and surface finish. It's really necessary that the investigation for the deep hole drilling by the BTA drill because its required quality should be satisfied with single pass. This thesis deal with the experimental results obtained during single tube BTA system machining on SM55C steel for different machining conditions. The results of the investigation on the optimum cutting condition selecting and tool life reveals as follows. (1) The optimum cutting condition was cutting speed, V = 42 m/min and feed speed. F = 90 mm/min and the tool life was about 10 meters. (2) Surface roughness was $12\mum$ and the roundness was less using $16mum$single edge BTA drill in testing cutting condition.

• 한국생산제조학회지
• /
• 제18권5호
• /
• pp.529-535
• /
• 2009

One of the most important things in shipbuilding is to select light and high tensile strength materials. Therefore, the use of Al alloy in shipbuilding become an increase. In cutting the aluminum plate, the quality of the cut surface is strongly influenced by the cutting conditions such as cutting speed, kerf width, plate thickness, cutting materials, and applied gas pressure. The cutting experiment of Al alloy plate(5083) were carried out using LASER cutting machine. The upper and lower of kerf width, the surface roughness(Ra, Rmax) of cut surface were measured under various cutting conditions. The morphologies of cutting surface were also monitored at various cutting conditions. The optimum cutting conditions of Al alloy among tested were indicated.