• 전자공학회논문지
• /
• 제52권6호
• /
• pp.32-40
• /
• 2015

본 논문에서는 무인항공기에 탑재된 안테나 간의 간섭을 고려한 안테나 최적 위치 분석에 대해서 서술하였다. 분석은 전방향성 안테나들 중 운용 주파수 대역이 인접하고, 상호 간 이격거리가 가까운 곳에 위치한 안테나들을 선정하여 수행하였다. 분석을 수행한 안테나는 제어용 데이터링크, TCAS(Traffic Collision & Avoidance System), IFF(Identification Friend or Foe), GPS(Global Positioning System)와 RALT(Radar ALTimeter) 안테나들이다. 안테나 최적 위치 분석은 세 단계로 구분된다. 첫 번째 단계는 안테나 용도, 형상 및 방사패턴을 고려한 안테나 초기 위치 선정 후 안테나 장착 시 무인항공기 구조물에 의한 안테나 방사패턴과 반사손실 특성 변화를 관찰하여 최적의 특성을 갖는 지점을 선정하는 것이다. 두 번째 단계는 안테나 간의 결합특성과 송신 안테나의 불요파 세기 및 수신 안테나의 최저수신감도를 고려하여 안테나 간 간섭 정도를 분석하는 것이다. 간섭이 발생할 경우, 간섭이 미발생하는 최소이격거리를 분석하여 간섭이 발생하지 않는 최적 위치를 선정한다. 마지막 단계는 안테나 간 추가 거리 이격으로도 간섭이 제거되지 않을 경우, 안테나 간 주파수 이격 분석을 통한 주파수 간섭 대책을 확정하는 것이다. 이러한 분석 과정은 개발단계에서 안테나 간 간섭을 예측하여 간섭이 발생하지 않는 안테나 최적 위치 선정에 유용하게 사용된다.

• 대한조선학회지
• /
• 제4권1호
• /
• pp.49-54
• /
• 1967

The authors considered the effects of trim in the small coastal passenger boat upon resistance in this paper. Any change of trim no matter how small, necessarily produces some effect upon resistance. The relations between the resistance coefficients and trim were investigated through the towing test of the Model $MCI-P_1-65$, Korean Standardized Ship, GT 70 tons passenger boat in the gravitational tank. The Lines of the Model are given in Fig. 1. Principal dimensions and other characteristics vary with the trim in general. Those values varied with the trim for $MCI-P_1-65$ are tabulated in table 1. The resistance was measured at five conditions such as even keel, 0.0273L, (original designed trim) 0.0473L, 0.0663L, 0.0873L trim by the stern, fixing the displacement corresponding to the designed load water line. Model was made of wood in length of 3.5 feet coated with varnish, and without appendages. As the artificial turbulent stimulator, the sand strip method was used. The results of model towing tests, correcting to water temperature of $70^{\circ}F$, were expanded to full scale using the Schoenherr's friction formula and surface roughness allowance coefficient of 0.0004. The authors point out, the following results. 1) Optimum trim which gives the minimum resistance exists for every speed at constant displacement and each comes to the same value. For $MCI-P_1-65$ optimum trim is 0.0673L trim by the stern(Fig.4-The cross curves of the resistancecoefficients). 2) At constant displacement, when LCB(longitudinal position of center of buoyancy) varies with the trim, there exists optimum value of LCB which gives minimum resistance for every speed and each comes to the same value. For $MCI-P_1-65$ optimum position of LCB is 8%L aft from midship section (Fig.6).

• Earthquakes and Structures
• /
• 제25권5호
• /
• pp.359-367
• /
• 2023

High-rise structures are considered as symbols of economic power and leadership. Developing countries like India are also emerging as centers for new high-rise buildings (HRB). As the land is expensive and scarce everywhere, construction of tall buildings becomes the best solution to resolve the problem. But, as building's height increases, its stiffness reduces making it more susceptible to vibrations due to wind and earthquake forces. Several systems are available to control vibrations or deflections; however, outrigger systems are considered to be the most effective systems in improving lateral stiffness and overall stability of HRB. In this paper, a 42-storey RCC HRB is analyzed to determine the optimum position of outriggers of different materials. The linear static analysis of the building is performed with and without the provision of virtual outriggers of reinforced cement concrete (RCC) and pre-stressed concrete (PSC) at different storey levels by response spectrum method using finite element based Extended3D Analysis of building System (ETABS) software for determining responses viz. storey displacement, base shear and storey drift for individual models. The maximum allowable limit and percentage variations in earthquake responses are verified using the guidelines of Indian seismic codes. Results indicate that the outriggers contribute in significantly reducing the storey displacement and storey drift up to 28% and 20% respectively. Also, it is observed that the PSC outriggers are found to be more efficient over RCC outriggers. The optimum location of both types of outriggers is found to be at the mid height of building.

• 경영과학
• /
• 제34권2호
• /
• pp.103-113
• /
• 2017

The artillery is a key element of the ground forces operation during wartime, and the military engineers support the artillery position development operation to support the smooth operation of the artillery. In establishing the artillery position development operation plan, the commander requires more than his intuition to find the best option reflecting a number of elements of the battlefield situation which changes every minute. Moreover, the number of available equipment is smaller than the number of required position developments, and the effective equipment operation becomes essential element of this issue. This study quantified the capability of the available engineering equipment, organized a number of teams enabling equipment to put out the maximum capacity based on the quantified figures, and formed the model which allocates the team to the developing points to minimize the developing time. The goal programming method was applied to resolve the problem. The developed model was applied to compare the total mission duration following the number of teams, the variable for commander's decision, and the result of this study can be used as the quantitative data for commander's decision making process in establishing the artillery position development support operation through effective equipment management.

• 한국기계가공학회지
• /
• 제18권2호
• /
• pp.14-21
• /
• 2019

In recent years, the use of composite structures has become commonplace in various fields such as aerospace, architecture, and civil engineering. In this study, A method is proposed to find optimal position of bolt hole for fastening of composite structure. In the case of composites, stress distribution is very complicated, and design optimization based on this phenomenon increases difficulty. In selecting the optimum position of the bolt hole, the response surface method(rsm), which is a method of optimization, was applied. A response surface was created based on design points by multiple finite element analyzes. The position of the bolt hole that minimizes the stress when bolting on the response surface was found. The distribution of the stress at the position of the optimal hole was much lower than that of the initial design. Based on the results of this study, it is possible to increase the design safety factor of the structure by appropriately selecting the position of the bolt hole according to various load types when designing the structure and civil structure.

• Journal of Welding and Joining
• /
• 제29권3호
• /
• pp.58-63
• /
• 2011

Bead shape control with gas force process has been developed to overcome the concave back bead in pipe orbital welding. However, It is impossible to make a convex back bead using the existing gas nozzle, because it has high gas-consuming and low gas force. The purpose of this paper, to develop optimum shape of nozzle which to reduce the consumption of gas, maximizing the shield gas force with low cost and high productivity coincide the Green welding. In this paper venturi-type nozzle was compared with existing CP-type nozzle by TIG pulse welding in overhead position. As a result, CP-type occurs the wormholes in the overhead position, but the Venturi-type without the pore and formed a good bead appearance.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권6호
• /
• pp.16-24
• /
• 2017

본 논문은 오프셋 아웃리거의 최적위치를 알기 위하여 우선 아웃리거 구조시스템이 설치된 80층의 초고층건물을 대상으로 MIDAS-Gen을 이용하여 계획설계 수준의 구조설계를 실시하였다. 그리고 본 연구에서는 기둥의 강성, 아웃리거의 평면상 위치, 아웃리거의 설치 높이 등을 주요한 변수로 선택하여 구조해석을 진행하였다. 또한 초고층건물의 오프셋 아웃리거에 대한 최적위치를 찾는 것을 목적으로 초고층건물의 구조설계에서 가장 필수적인 최상층에서 발생하는 수평변위를 분석하였다. 본 연구의 결과, 기둥의 강성, 아웃리거의 평면상 위치, 아웃리거의 설치 높이는 아웃리거 구조시스템의 최적위치에 영향을 주는 것으로 나타났다. 또한 본 연구의 결과는 초고층건물의 오프셋 아웃리거 구조시스템의 최적위치를 알려주는 구조설계 자료로 유용하다고 사료된다.

• 한국음향학회지
• /
• 제40권4호
• /
• pp.270-277
• /
• 2021

강력초음파 분야에 있어서, 트랜스듀서의 고정을 위한 프렌지의 위치설정은 트랜스듀서의 변환효율에 큰 영향을 주는 중요한 요소이다. 본 연구에서는 볼트 체결형 란주반 초음파 트랜스듀서의 공진모드에 따른 프렌지의 설치 위치를 결정하기 위한 실험적 방법을 제안하였다. 제안된 방법에서는 반원형 쐐기 형태의 지그를 제작하여 트랜스듀서의 측면을 따라 이동하며 지그에 일정한 압력을 가한 후 트랜스듀서의 진동특성을 분석하였다. 압력을 가하는 위치에 따른 트랜스듀서의 입력 어드미턴스의 변화를 분석하여 프렌지의 최적의 위치를 결정할 수 있었다. 이 위치들은 메이슨 등가회로를 적용하여 계산한 공진 주파수 및 전송선로 모델 해석으로부터 계산한 각 공진 모드에 대한 입자속도 분포로부터 예측한 진동 모드의 절의 위치와 좋은 대응을 보이고 있어 본 연구에서 제안된 방법의 유효성을 확인할 수 있었다.

• 한국추진공학회지
• /
• 제25권3호
• /
• pp.1-13
• /
• 2021

추력이 최적화된 노즐의 초음속 유동장에 대한 노즐벽면각도의 영향이 수치해석적으로 조사되었다. 30톤급 로켓엔진의 연소기와 작동조건이 최적노즐형상을 조사하기 위하여 선택되었다. 연소생성물의 노즐유동은 케로신-액체산소의 이동평형계산에 의해서 구현되었다. 노즐벽면 각도의 변화는 내부충격파 및 2차 충격파의 발달형태를 다르게 유도하였다. 내부충격파가 노즐출구에서 특정위치에 있을 때 최적노즐이 얻어졌다. 최적노즐에 대한 노즐벽면 각도들은 충격파를 고려하지 않고 얻어진 최적노즐 형상과 매우 유사하게 얻어졌다.

• 전기학회논문지P
• /
• 제58권2호
• /
• pp.227-230
• /
• 2009

In this paper, we performed the optimum design of reactors for matrix-type superconducting-fault current limiters (SFCLs), using electromagnetic analysis tools. We decided a optimun position within a reactor for superconducting elements of current-limiting parts and trigger parts from the calculation of magnetic flux internsity for reactor structures. Also we decided effective distance length between two reactors through the analysis of the distribution of magnetic field, according to distance lengths between them. We designed and characterized matrix-type SFCLs, based on our optimum design of a reactor. We confirmed uniform distribution of a fault current, resulted from the improvement of simultaneous quench characteristics within our matrix-type SFCL.