• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.6
• /
• pp.403-410
• /
• 2009

This paper proposes a new approach to find the optimum ratios between sizes of the heat exchangers of the heat recovery steam generator (HRSG) system with limited size to maximize the efficiency of the steam turbine (bottom) cycle of combined cycle power plants (CCPP), but without performing the bottom cycle analysis. This could be achieved by minimizing the unavailable exergy (the sum of the destroyed and the lost exergies) resulted from the heat transfer process of the HRSG system. The present approach is relatively simple and straightforward because the process of the trial-and-error method, typical in performing the bottom cycle analysis for the system optimization, could be avoided. To demonstrate the usefulness of the present method, a single-stage HRSG system was chosen and the optimum evaporation temperature was obtained corresponding to the condition of the maximum useful work. The results show that the optimum evaporation temperature based on the present exergy analysis appears similar to that based on the bottom cycle analysis. Also shown is the dependency of size (NTU) ratios between the heat exchangers on the inlet gas temperature, which is another important factor in determining the optimum condition once overall size of the heat recovery steam generator is given. The present approach turned out to be a useful tool for optimization of the singlestage HRSG systems and can easily be extended to multi-stage systems.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3A
• /
• pp.194-200
• /
• 1999

In this paper studied was the piezoelectric properties of the $\beta$-PVDF organic thin films prepared by physical vapour deposition method. The molecular orientation of organic thin films was controlled by the application of an electric field and variation of substrate temperature during the evaporation process. Optimum conditions of manufacturing $\beta$-PVDF organic thin film by physical vapor deposition method is to keep at the substrate temperature of $80^{\circ}C$, at the applied electric field of 142.8 kV/cm. The voltage output coefficient increased from 1.39 to 7.04V increasing the force moment.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.3
• /
• pp.406-409
• /
• 1999

Thin films of silver with high reflectance of 95% and above were fabricated successfully on polyester substrate by using e-beam evaporation processes. The optimum process condition was investigated by varying the current values applied while keeping the substrate temperature at room temperature by circulating the cooling water around it during deposition. Thin films of silver deposited with 30 mA as current revealed the highest reflectance of 96.4%, while being illuminated with a light of 700nm wave-length. But their adhesion showed unsatisfactory results. Though the films showed a condensation type in the cross-sectional views, they revealed crystallinity in the planes of (111) and (200) and growth orientation in <100> direction.

• YAKHAK HOEJI
• /
• v.3 no.1
• /
• pp.26-34
• /
• 1957

The solar evaporation method is one of the most important and popular salt manufecturing method in Korea. The rate of evaporation of sea water depends on a complex climate factors. Of these factors, the most important is solar radiation and in particular the extent to which it is absorbed in the brine. By the addition of suitable dyestuff, a further increase in absorption is obtained and can result in all the radiation entering the brine being made available as heat. "Solivap Green", one of several dyestuffs which have been suggested for accelerating solar evaporation, was tested in this experiment. The results of the experiment. 1. Increase the evaporation rate of brine up to 20-25%. 2. Elevate the temperature of brine 2-$4^{\circ}C$. higher than that of brine adding no dyestuff. 3. Optimum dyestuff concentration is 25-30 mg/L and allowable maximum concentration can not exceeded 1000 mg/$m^2$ (50 mg/L). 4. Addition of dyestuff does not cause the degradation of salt produced. 5. A conversion table which indicates the concentrations for various depths of brine was prepared for engineering purpose. 6. Absorption spectrum of the dyestuff was studies, but toxicological and structural studies for the dyestuff have not been done in this experiment.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.4
• /
• pp.329-335
• /
• 2003

This study is on a experiment which shows to defrost automatically on the optimum time regardless of defrosting method. The result shows that the more defrost layers increase in fin tubes of evaporation, the less the section of the circulating air reduce. Thickness of the frost formation increases, so a pressure difference of ventilation increase, as a result automatic defrosting system sets the time COP drops suddenly up optimum time. Automatical defrosting system can find out the initial related current of evaporator fan motor and the value of load current in the optimum time. And it sets defrosting time, evaporating temperature, and temperature in refrigerator up system requiring value. Consequence of this experiment is that energy consumption with defrost load gets effect of reduction of eleven percent per 25.4 hours compared with common defrosting.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.17 no.5
• /
• pp.43-47
• /
• 1980

Transparent conducting films of In2O3 were fabricated by elect yon beam evaporation method in an oxygen atmosphere of -10-4 Torr., and the optimum conditions of film deposition, as well as their electrical and optical properties were measured and analysed. Evaporation rate of 3~7A/sec, substrate temperature of over 30$0^{\circ}C$, and SnO2 doping of 2~5wt. % were the optimum deposition conditions. Under these conditions , the resistivities of the films were 2$\times$10-4 $\Omega$.cm and the visible transmittances were 85~90%.

• The Korean Journal of Food And Nutrition
• /
• v.13 no.2
• /
• pp.152-157
• /
• 2000

In order to select the optimum drying method for the production of cinnamon extract, water extract and 70% ethanol extract of cinnamon were prepared. And then several drying method of oven drying, vacuum evaporation, spray drying and freeze drying were performed. Content of cinnamic acid, cinnamic aldehyde, eugenol, tannin and free sugar, and antioxidant activity, degree of browning, pH, color value, turbity and solubility were compared. In water extract, contents of cinnamic acid, cinnamic aldehyde, eugenol were 29.45mg/100g, 94.86mg/100g, 120.75mg/100g and decreased to 4.76%∼44.21%, 5.30%∼48.05%, 3.66%∼21.83% by oven dyring, vaccum drying, spray drying respectively, but freeze drying showed a little decrease of those components. In 70% ethanol extract, effectual components decreased to 76.05%∼88.38% and 26.86%∼78.76% by freeze drying and vacuum evaporation respectively. Antioxidant activity decreased by drying and decreasing rate in 70% ethanol extract was lower than water extract. Degree of browning increased as the drying temperature increased. Tannin and free sugars were little affected by drying temperature. Solubility decreased in oven drying and 70% ethanol extract. Overall data suggested that optimum drying methods of cinnamon extract were freeze drying in case of water extract and freeze drying and vaccum drying in case of 70% ethanol extract.

• Journal of the Korean Vacuum Society
• /
• v.12 no.1
• /
• pp.1-6
• /
• 2003

An axial electron beam gun system, which emits the electron beam power of 50 kW, has been manufactured. The electron beam gun consists of two parts. One is the electron beam generation part. including the filament, cathode, and anode. The maximum beam current is 2 A and the acceleration voltage is 25 kV. The other part includes the focusing-, deflection-, and scanning coils. The beam diameter and ham trajectory can be controlled by these coils. The characteristic of each part is measured ior the optimum condition of evaporation process. Moreover, Helmholtz coil is installed inside the vacuum chamber to adjust the incident angel of the beam to the melting surface for the maximum evaporation. We report on the evaporation rates for zirconium(Zr) and gadolinium(Gd) metals which have the high melting temperatures.

• Resources Recycling
• /
• v.6 no.4
• /
• pp.3-10
• /
• 1997

Electric are furnace dust (EAF dust) generated in steel production based on scrap melting is contained Zn and Fe about 25 and 30 percent by weight, respectively. From a metallurgical point of view, the dust could be regarded as a raw material for Zn and Fe source. To recover the Zn in the metal from EAF dust, many system are proposed such as Arc Plasma Furmace and Pb splasher method. In this study, to recover high purity Zn from Pb splasing alloy, Zn distillation is carried out at the temperature of 1123, 1173, 1223, 1273 K, the gas flow rate of 2.5, 5.0, 8.0 Ni/min and the distilling time of 10, 30, 60, 90 minutes. The main results obtained from this study are as follows:(1) The amount of evaporated Zn and its evaporating rate increased with increasing temperature, but purity of Zn decreased with increasing temperature. Optimum temperature range was found out to be between 1173∼1223K. (2) The amount of evaporated Zn and evaporation rate increased with increasing gas flow rate at a given temperature and distillation time. Gas flow rate has more influence over the amount of evaporated Zn and evaporation rate with increasing temperature.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.150-156
• /
• 1986

A Rankine cycle including heat exchange processes in the steam generator has been analyzed by the concept of available energy. The operation condition of the cycle can be expressed with the evaporation temperature, and there exists an optimum power condition at which the thermal efficiency of the cycle is almost the same as that of the Carnot cycle at the maximum power condition. The mass flow rate of the working fluid increases sharply as the evaporation temperature approaches to the critical point, and the regenerative system is needed to operate the cycle at the maximum power condition.