• Land and Housing Review
• /
• v.3 no.2
• /
• pp.177-185
• /
• 2012

LH applies a uniformly standardized PHC Pile to 15~25 stories of Shear-wall type Apartment Building. Recently it is predicted that LH will construct over 30~40 story Apartment Building to keep varied project condition and faces urgent needs to save construction cost for improving its competitiveness. Therefore, structural analysis and design on the upper part and foundation of apartment building were carried out in this study by subdividing story of apartment building, e.g. 15, 20, 25, 30, 35, 40 stories. Reflecting the result of basement analysis and design, the economic evaluations are performed and the optimum diameters of PHC piles are suggested. The result of this paper is considered to be applied usefully for foundation design of LH apartment housing, and the suggested PHC Piles can be used effectively by increasing efficiency and saving the construction cost of foundation.

• Fashion & Textile Research Journal
• /
• v.7 no.5
• /
• pp.547-552
• /
• 2005

The study has objective in raising value of the gray color as a meaningful color suiting sentiments of modern people by expressing the gray color in various perspective utilizing natural dyes that is natural at the same time having aesthetic color tones. For example, the main ingredient used for coloring black and gray color is the pyrogallol tannin and the gray tone dye can be acquired by combining the tannin with iron. In order to find the suitable condition for processing tannin, UV-Vis part absorption spectrum of Gallapple pyrogallol tannin, dye ability based on temperature and time, reflection rate based on concentration, color changes based on acid treatment and alkali treatment, changes on surface based on concentration or metal mordant condition, and lightfastness were measured. Maximum absorption wavelength (${\lambda}_{max}$) of Gallapple tannin was at around 273 nm, while strong absorption was also observed at below 350 nm. Dye ability of Gallapple tannin is done more easily on silk rather than cellulose fibers such as cotton, while the optimum condition for dyeing was observed to be at $60^{\circ}C$, for 20 minutes. As a result of acid treatment, the color of dye material consist highly of gray tones and showed red tone after the alkali treatment. While it was observed that as dye concentration and metal mordant concentration increased the color changed at counter-clockwise direction on the Y-scale of Munsell's scale of colors. Lightfastness was more on a normal fading. I hope this study opens up possibilities towards presenting gray color expressed from tannin as color with diversity and aesthetic value. In future, comparative study between dye expressed from catechol tannin dye materials will be helpful.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.3
• /
• pp.219-225
• /
• 2010

Optimal grinding condition was examined by changing only the size of screen opening with fixing other factors to produce coal fines of particle sizes required for circulating fluidized bed gasifier. At least 85 wt% of the coal particles should fall into the size range of 0.045~1.0 mm for efficient gasification. In this study, hammer mill was used to grind Chinese low rank lignite coal following grinding condition designed by Taguchi method. The analysis of signal to noise ratio showed that optimum grinding condition for the gasifier was 3 mm in primary screen size and 1.3 mm in secondary screen size on the 95% level of significance.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.6
• /
• pp.237-242
• /
• 2008

The effects of the process parameters in the molding of aspheric glass lenses for camera phone modules have been investigated experimentally. The molding conditions were optimized with respect to the form accuracy (PV) (the response variable) of the molded lens. The experimental conditions were obtained by employing a factorial design method. From the analysis of variance (ANOVA) and P-value (significance level), the slow cooling rate was found to affect the response variable most significantly. The lens molded under the optimum molding condition showed a transcription ratio of 93.4%.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.11
• /
• pp.137-145
• /
• 2002

Electric vehicle body has to be subjected to uniform load and requires auxiliary equipment such as air pipe and electric wire pipe. Especially, the cross beam supports the weight of passenger and electrical equipments. a lightweight vehicle body is salutary to save operating costs and fuel consumption. Therefore this study is to perform the size and the shape optimization of crossbeam for electric vehicle using the method of topology optimization to introduce the concept of homogenization based on optimality criteria method which is efficient for the problem having the number of design variables and a few boundary condition. this provides the method to determine the optimum position and shape of circular hole in the cross beam and then can achieve the optimal design to reduce weight.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1051-1052
• /
• 2011

This paper deals with optimum design criteria to minimize the torque ripple of a concentrated winding Synchronous Reluctance Motor(SynRM) using Response Surface Methodology(RSM). The feasibility of using RSM with the finite element method(FEM) in practical engineering problem is investigated with omputational examples and comparison between the fitted response and the results obtained from an analytical solution according to the design variables of stator and rotor in concentrated winding SynRM(6slot). The focus of this paper is the efficiency evaluation on the basis of load condition in a Concentrated Winding Synchronous Reluctance Motor and distributed Winding Synchronous Reluctance Motor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.111-115
• /
• 2017

This forged piston is proposed with a lighter weight and higher durability than a gravity casting piston for gasoline engines. However, a forged piston is very difficult to develop and mass-produce due to lack of basic technologies such as design, material and forging technique. First, we benchmarked existing forged pistons according to database design parameters. Second, we evaluated two solidification processes, continuous casting and spray forming, to produce heat-resistant alloy billets for forging. The spray forming process gives better mechanical properties at all temperatures, particularly at elevated temperatures except when poor formability is present. We used DEFORM simulation to determine the optimum process condition with billet from spray forming and successfully commercialized it with LF Sonata HEV.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1436-1440
• /
• 1996

The wear mechanism of material is an important mechanic property to select a material's life and a optimum work condition. Although there are many researches about a wear mechanism of material, the pin-on-disc type tribotester is widely known to us. It is difficult to add a variable and heavy load in the existing pin-on-disc type tribotester to estimate this wear mechanism. And due to a rotation of a disc, it is impossible to add a constant force. But we can solve this problem by using a hydraulic servo system. Therefore, in order to investigate a wear mechanism of materials, it is necessary to design a hydraulic pin-on-disc type tribotester and construct a controller against a variable disturbance.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.1 no.1
• /
• pp.51-62
• /
• 1972

In Korea, fermented fish has been playing an important role as a preserved and flavor rich food. It is said that the digestion of fish protein is due to both action of intrinsic (autolytic enzymes) and bacterial enzymes in fish. The mass production of fermented fish has been impeded since traditional method of fermentation requires a long duration for a complete digestion. A high concentration of salt and unsanitary condition are also considered disadvantages of the old method. To improve the quality of the product and to develop mechanized process of fermentation, fermentors which have such control device as temperature, pH and agitation control system have been urgently needed. In this study, a model design of a fermentor is studied. The calculation was based on the optimum conditions for enzymatic hydrolysis of fish protein which involve temperature, pH, viscosity and other factors.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.147-151
• /
• 2000

This paper presents an analysis of a slot on the broad wall of a rectangular waveguide using the 3D FDTD method. In order to reduce the reflection loss, Mur's 2nd absorbing boundary condition is used. To realize the optimum design by FDTD, the effects of time step, excitation aperture size, analysis region and excitation position in model are derived. The analysis results are compared with the experimental results and they show a good agreement with each other.