• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.414-417
• /
• 2005

Single point diamond turning technique for optical crystals is studied in this paper. The main factors which are influential the machined surface quality are discovered and regularities of machining process are drawn. Optical crystals have found more and more important applications in the field of modern optics. Optical crystals are mostly brittle materials of poor machinability. The traditional machining method is polishing which has many shortcomings such as low production efficiency, poor ability to be automatically controlled and edge effect of the workpiece. The purpose of our research is to find the optimal machining conditions for ductile cutting of optical crystals and to apply the SPDT technique to the manufacturing of ultra precision optical components of brittle material(Ge). Many technical challenges are being tried for the large space infrared telescope, which is one of the major objectives of the National Strategic Technology Road Map (NSTRM).

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.76-81
• /
• 2011

UV imprinting process can manufacture high-functional optical components with low cost. If hard polymers can be used as transparent molds at this process, the cost will be much lower. However, there are limited researches to predict the machinability and the burr of hard polymers. Therefore, a new method to predict them by analyzing load-depth curves which can be obtained by the instrumented indentation test was developed in this study. The load-depth curve contains elastic deformation and plastic deformation simultaneously. The ratio of the plastic deformation over the sum of the two deformation is proportional to the ductility of materials which is one of the parameters of the machinability and the burr. The instrumented indentation tests were performed on the transparent molds of the hard polymers and the values of ratio were calculated. The machinability and the burr of three kinds of hard polymers were predicted by the ratio, and the prediction was in agreement with the experimental results from the machined surfaces of the three kinds of hard polymers.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.184-187
• /
• 2005

This paper is described about the technique of ultra-precision machining for optical parts in HMD system. Machining technique for PMMA and BK7 with single point diamond turning machining is reported in this paper. The main factors influencing on the machined surface quality are discovered and regularities of machining process are drawn. The purpose of our research is to find the optimum machining conditions fur cutting of PMMA and grinding of BK7. Also, apply the SPDTM technique to the manufacturing of ultra precision optical components of HMD system. Aspheric PMMA lens without a polishing process, the surface roughness of 5 nm Ra, and the form error of ${\lambda}/2\;({\lambda}=632.8nm)$ for reference curved surface 30 mm has been required.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.6
• /
• pp.709-715
• /
• 2011

Chattering in cutting operations are usually a cumbersome part of the manufacturing process in mechanical. Particular, machining performance such as that of the boring process is limited by cutting condition at the movable components. Among various sources of chatter vibration, detrimental point in cutting condition is found a mechanical condition on overhang. It limits cutting speed, depth, surface roughness and tool wear failure as result because the all properties are varying with the metal removal process. In this case, we have to observe the resonance frequencies of a boring bar for continuous cutting. In the established research, boring bar vibration of cutting system has been measured with the aid of accelerometer. However, the inherent parameters of internal turning operations are severely limit for the real time monitoring on accelerometers. At this point, this paper is proposed other method for real time monitoring during continuous cutting with optical fiber at the inside of boring bar. This method has been used a plastic fiber in the special jig on boring bar by based on experimental modal analysis. In this study, improvement of monitoring system on continuous internal cutting was attempted using optical fiber sensor of inside type because usually chattering is investigated experimentally measuring the variation in chip thickness. It is demonstrated that the optical fiber sensor is possibility to measure of chattering with real time in boring process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.1
• /
• pp.79-84
• /
• 2004

A light-guide is one of several important components of backlight unit in TFT-LCD. The manufacturing technology and optical system design of the light guide is very sensitive to quality and cost of the TFT-LCD module. In the present study a new manufacturing method which is called as direct surface forming(DSF) has been tested under various conditions. DSF is very similar to the well-known hot embossing except for partial contact between mold and substrate. The final V-groove pattern shows different shapes depend on the temperature of mold surface, contact time of mold and depth of V-groove.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.83-87
• /
• 2001

A 110 mm diameter aspheric metal secondary mirror for a test model of an earth observation satellite camera was fabricated by ultra-precision single point diamond turning (SPDT). Aluminum alloy for mirror substrates is known to be easily machinable, but not polishable due to its ductility. A harder material, Ni, is usually electrolessly coated on an Al substrate to increase the surface hardness for optical polishing. Aspheric metal secondary mirror without a conventional polishing process, the surface roughness of Ra=10nm, and the form error of $Ra={\lambda}/12({\lambda}=632nm)$ has been required. The purpose of this research is to find the optimum machining conditions for reflector cutting of electroless-Ni coated Al alloy and apply the SPDT technique to the manufacturing of ultra precision optical components of metal aspheric reflector.

• Ceramist
• /
• v.9 no.6
• /
• pp.7-11
• /
• 2006

The status of structural ceramics in Japan is presented. Use of ceramics for structural components had been limited due to their brittleness, and the successful application was wear resistant parts such as thread guides and ceramic cutting tools up to around 1980. Since then, considerable work has been done for applying ceramics to mechanical parts, and automotive components made of silicon nitride were developed and commercialized in 1980s. Unfortunately, the application of silicon nitride to automotive engines is not so popular in these days. Instead, a variety of structural ceramics such as alumina, silicon carbide and zirconia have recently extended the market, and the expanded application includes vacuum process parts for manufacturing semiconductor and liquid crystal devices, refractory tubes for casting aluminum alloy, and dies for optical lens forming. In addition, cordierite honeycombs and diesel particulate filters are widely used in automobiles. In the present review, the recent application of structural ceramics to automobiles and industries in Japan is summarized.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.773-777
• /
• 2012

Recently UV laser micromachining processes is widely introduced to meet the needs of advanced components of IT, BT and ET industries. Due to the characteristics of non-contact and high-speed laser processing, UV laser micromachining is applied to manufacture very thin substrate such as polymer, metals and composite. These minimum line width obtained by UV laser micromachining is generally determined from laser wavelength, optical lens and its numerical aperture. In this paper we will show the lens effect of water droplet on the surface of workpiece to reduce the line width when UV laser light is irradiated and focused through the water droplet. Because of the refraction effect generated by the semi-spherical or spherical shape of water droplet, we can find smaller line width. And water droplet could not only protect thermal deformation, but also carry away burr around micro dent. Firstly fundamental theory of minimum line width was derived from relationship between the geometry of water droplet and laser light trace, and then experimental and simulation results will be finally compared to verify the effectiveness of water droplet lens effect of UV laser micromachining process.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.6
• /
• pp.114-120
• /
• 2021

This study is focused on the root mean square and peak-to-valley based on the injection conditions of the f-theta lens, one of the main components of laser printers and laser scanning systems. The f-theta lens of an aspherical plastic lens requires ultra-preaction. Injection molding is typically used for the mass production of aspherical plastic lenses. In the injection-molding method, the resin in the lens shape is filled with the resin after melting the plastic pellets at a constant temperature and then cooled. It is necessary to maintain a uniform injection molding system to produce high-quality lenses. These injection-molding systems are influenced by different factors, such as pressure, speed, temperature, mold, and cooling. It is possible to obtain a lens that exhibits the optical characteristics required to achieve harmony. We investigated the root mean square and peak-to-valley caused by variations in temperature, a critical parameter in the melting and cooling of plastic resins generated inside and outside the injection mold.

• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.12-17
• /
• 2012

In order to produce high-quality optical components, aspheric lenses have been widely applied in recent years. An aspheric lens consists of aspheric surfaces instead of spherical ones, which causes difficulty in the design process as well as the manufacturing procedure. Although injection molding is widely used to fabricate optical lenses owing to its high productivity, there remains lots of difficulty to determine appropriate mold design factors and injection molding parameters. In the injection molding fields, computer simulation has been effectively applied to analyze processes based on the shell analysis so far. Considering the geometry of optical lenses, a full-3d simulation based on solid elements has been reported as a reliable approach. The present work covers three-dimensional injection molding simulation and relevant deformation analysis of an injection molded plastic lens based on 3d solid elements. Numerical analyses have been applied to the injection molding processes of three aspheric lenses for an image sensing module of a mobile phone. The reliability of the proposed approach has been verified in comparison with the experimental results.