• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.388-399
• /
• 2003

Light losses in optical fibers are investigated by a fiber optic OTDR (Optical Time Domain Reflectometry) sensor system to develop fiber optic probes for structural strain measurement. The sensing fibers are manufactured 3 kinds of fibers: one is single mode fiber, and second is multimode fiber, and the third is low-cladding-index fiber. Fiber bending tests are performed to determine the strain sensitivity according to the strain of gage length of optical fibers. In the result of this experiments, the strain sensitivity of the single mode fiber was shown the highest value than others. The fiber optic strain probe was manufactured to verify the feasibility of the structural strain measurement. In this test, the fiber optic strain probe of the OTDR sensor could be easily made by the single mode fiber.

• Transactions of the Society of Information Storage Systems
• /
• v.7 no.2
• /
• pp.75-79
• /
• 2011

Recently mobile phone camera become generally spread, it is required to develop high resolution, multi-functional camera module for obtaining high image quality. To satisfy this demand, number of pixels has been increased and pixel size decreased in small mobile phone cameras. As a result, image quality is seriously dropped by blur phenomena. Especially when hand tremble is occurred, image quality is dropped by camera shake. Therefore, to obtain high quality image, it is necessary to compensate user's hand tremble. In this paper, we propose voice coil actuator for compensating hand tremble, which can apply optical image stabilization (OIS) system. Sensitivity analysis and size optimization are performed to obtain high driving force. Finally, it is confirmed that the optimized electromagnetic circuit can be applied in OIS system.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.6
• /
• pp.372-375
• /
• 2005

The tracking performance of optical disk drive(ODD) system can be improved using disturbance observer(DOB). But, DOB was not easily applied in the ODD system because the additional microprocessor was needed. In this paper, we propose an error-based modified disturbance observer(EM-DOB) for ODD system. Due to the simplified structure of EM-DOB, the system is easily implemented to the digital control algorithm or the analog circuit. In these algorithms, disturbances rejection performance of system can be tuned as Q filter parameters are selected. Based on analysis of sensitivity function, three guidelines of Q filter design are suggested. Experimental results of DOB and EM-DOB are evaluated under the forced disturbances.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.385-389
• /
• 2003

To make high speed spindle system work properly, sensors with outstanding resolution and dynamic characteristics are essential. An optical fiber displacement sensor is based on simple principles. Electrical signal responds to the optical flux change due to the displacement change between a target and a sensor probe. In this paper, the performance of optical fiber displacement sensor has been investigated according to properties of optical fiber Firstly, optical loss has been measured before and after polishing optical fiber endface. Secondly, allowance of optical fiber bending has been tested. thirdly sensitivity and linear range of the sensor has been found out according to the shape of cross section of optical fiber.

• 한국정보통신설비학회:학술대회논문집
• /
• 2006.08a
• /
• pp.19-23
• /
• 2006

Latching optical switches and optical logic gates AND and OR are demonstrated, for the first time, by the monolithic integration of a vertical cavity lasers with depleted optical thyristor structure, which have not only a low threshold current with 0.65 mA. but also a high on/off contrast ratio more than 50 dB. By simple operating technique with changing a reference switching voltage, this single device operates as two logic functions, optical logic AND and OR. The thyristor laser fabricated using the oxidation process achieved a high optical output power efficiency and a high sensitivity to the optical input light.

• Journal of Astronomy and Space Sciences
• /
• v.31 no.3
• /
• pp.241-246
• /
• 2014

The Amon-Ra instrument is the main optical payload of the proposed EARTHSHINE satellite. It consists of a visible wavelength instrument and an IR energy channel instrument to measure a global Earth albedo. We report a new sensitivity technique for efficient alignment of the visible channel instrument. Whilst the sensitivity table method has been widely used in the alignment process, the straightforward application of the method tends to produce slow process convergence because of shop floor alignment practice uncertainties. We investigated the error sources commonly associated with alignment practices and used them when estimating the Zernike polynomial coefficients. Aided with single center field wavefront error (WFE) measurements and their corresponding Zernike polynomial coefficients, the method involves the construction and use of an experimental, instead of simulated, sensitivity table to be used for alignment state estimations. A trial alignment experiment for the Amon Ra optical system was performed and the results show that 71.28 nm in rms WFE was achieved only after two alignment iterations. This tends to demonstrate its superior performance to the conventional method.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.109-120
• /
• 2005

In this paper, bit error rate (BER) characteristics, sensitivity and minimum allowable launching power are numerically investigated as a function of amplifier spacing that consisted of 1,200 km WDM systems with MSSI method. It is conformed that the sensitivity and minimum allowable launching power are gradually degraded as amplifier spacings are gradually expanded, but those are not largely affected by modulation format. The sensitivity of RZ transmission system is smaller than that of NRZ transmission system, but minimum allowable launching power of NRZ transmission system is smaller than that of RZ transmission system. And, it is confirmed that the best amplifier spacing in NRZ and RZ transmission system is less than 50 km, because the sensitivity and minimum allowable launching power are less affected by fiber dispersion, channel wavelength and pump light power.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.11
• /
• pp.976-980
• /
• 1994

The sensitivity factors and the error propagation factors are defined for the three-parameter ellipsometry (TPE). The sensitivity factor is useful for understanding the nature of the TPE measurements in connection with determination of the optical properties and the thickness of a film. On the other hand, the error propagation factors provide a quantitative tool for predicting the optimum condition for TPE experiments. Their usefulness is demonstrated for the passive film formed on nickel in aqueous solution.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.693-698
• /
• 2008

For designing intensity modulation type optical microphone, the irradiance distribution which can be applied to inclined-cut geometrical configuration is suggested. The model is important in analysis of response characteristics f3r intensity modulation type optical microphone. To overcome low sensitivity problem in intensity modulation type optical microphone, inclined-cut optical fiber is considered here. Based on optical geometry, the inclined-cut optical fiber sensor is designed and fabricated. The experiments are carried out to evaluate sensor performance.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.12
• /
• pp.1270-1277
• /
• 2008

For designing intensity modulation type optical microphone, the irradiance distribution which can be applied to inclined-cut geometrical configuration is suggested. The model is important in analysis of response characteristics for intensity modulation type optical microphone. To overcome low sensitivity problem in intensity modulation type optical microphone, inclined-cut optical fiber is considered here. Based on optical geometry, the inclined-cut optical fiber sensor is designed and fabricated. The experiments are carried out to evaluate sensor performance.