• Korean Journal of Optics and Photonics
• /
• v.31 no.2
• /
• pp.105-110
• /
• 2020

A compact beam combiner based on two-mode interference (TMI) in multimode waveguides is proposed, and its feasibility is shown through simulation with the three-dimensional beam propagation method. The input waveguides are separated by about 1 ㎛ at the interface with the multimode waveguide, so that the fabricated waveguide pattern is well repeated. The power transmission to the output port from the red, green, and blue input port is 93.5%, 94%, and 93%, respectively. When the wavelength deviation from a center wavelength is 10 nm, the power transmission is maintained to be greater than 90%. When the waveguide width error is 40 nm, the power transmission is maintained to be greater than 85% for all the three colors. The polarization dependence of the beam combiner is almost negligible, and its size is as tiny as 0.02 × 4 ㎟.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.5
• /
• pp.863-870
• /
• 2019

In the GSM method for OWC-MIMO System, it is important to select an activation pattern set(: APS) for the performance optimization in the environment where mutual interference is high depending on the location of the transmitter and receiver. However, due to the high computational complexity, a high cost is paid in selecting the transmission APS. In this paper, we propose a method to reduce the candidate APS by pre-determining basic APS when generating candidate APS. The simulation results show that the proposed method has the same BER performance and reduce the computational complexity by 90% compared to the general GSM method in the high interfering environment.

• Current Optics and Photonics
• /
• v.8 no.4
• /
• pp.355-365
• /
• 2024

Wavefront coding (WFC) imaging systems can redistribute the energy of an interference laser spot on an image plane sensor by wavefront phase modulation and reduce the peak intensity, realizing laser protection while maintaining imaging functionality by leveraging algorithmic post-processing. In this paper, a spiral axicon WFC imaging system is proposed, and the performance for laser protection is investigated by constructing a laser transmission model. An Airy disk on an image plane sensor is refactored into a symmetrical hollow ring by a spiral axicon phase mask, and the maximum intensity can be reduced to lower than 1% and single-pixel power to 1.2%. The spiral axicon phase mask exhibits strong robustness to the position of the interference laser source and can effectively reduce the risk of sensor damage for an almost arbitrary lase propagation distance. Moreover, we revealed that there is a sensor hazard distance for both conventional and WFC imaging systems where the maximum single-pixel power reaches a peak value under irradiation of a power-fixed laser source. Our findings can offer guidance for the anti-laser reinforcement design of photoelectric imaging systems, thereby enhancing the adaptability of imaging systems in a complex laser environment. The laser blinding-resistant imaging system has potential applications in security monitoring, autonomous driving, and intense-laser-pulse experiments.

• Journal of Korea Multimedia Society
• /
• v.14 no.5
• /
• pp.658-668
• /
• 2011

Over the past decade, the improvement of communications technologies and the rapid spread of www (World Wide Web) have brought on the exponential growth of users using Internet and real time multimedia multicast services like video conferencing, tele-immersive virtual reality, and Internet games. The dense-wavelength division multiplexing (DWDM) networks have been widely accepted as a promising approach to meet the ever-increasing bandwidth demands of Internet users, especially in next generation Internet backbone networks for nation-wide or global coverage. A major challenge in the next generation Internet backbone networks based on DWDM technologies is the resolution of the multicasting RWA (Routing and Wavelength Assignment) problem; given a set of wavelengths in the DWDM network, we set up light-paths by routing and assigning a wavelength for each connection so that the multicast connections are set-upped as many as possible. Finding such optimal multicast connections has been proven to be Non-deterministic Polynomial-time-complete. In this paper, we suggest a new heuristic multicast routing and wavelength assignment method for multicast sessions called DVS-PMIPMR (Differentiated Virtual Source-based Priority Minimum Interference Path Multicast Routing algorithm). We measured the performance of the proposed algorithm in terms of number of wavelength and wavelength channel. The simulation results demonstrate that DVS-PMIPMR algorithm is superior to previous multicast routing algorithms.

• Korean Journal of Optics and Photonics
• /
• v.20 no.5
• /
• pp.272-275
• /
• 2009

In order to enhance the background noise filtering performance of the white light interferometry(WLI), we demonstrate the noise filtering performance of preprocessing of the measured fringe signals. The WLI was realized through a mirau interferometer which was equipped with a green LED. When measuring large-height and rough surface objects, the illumination optics are considered the numerical aperture(NA) and the depth of focus(DOF). In this case, the limited NA of the illumination optics has a considerable impact on the interference fringe. Therefore, we propose a preprocessing method that uses the intensity difference between the measured intensity and the moving average intensity. The performance is demonstrated by measuring an array of metal solder balls fabricated on printed circuit board(PCB). The proposed method reduces the noise pixels by 15 percent.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.603-615
• /
• 2020

The design factors of artificial recharge are determined by considering the hydrogeological characteristics of the aquifer. The optimal design factors for artificial recharge were derived after performing the injection tests step by step for each injection type (vertical well, ditch and mixed type), which were built in the test site of the study area. It was analyzed that the difference in the injection effect according to the diameter of the injection well was not large, and the 100 mm well was evaluated as appropriate in consideration of the availability and economy of land use. Since the injection effect was well maintained even in the upper rock, the depth of the injection well was proposed for the alluvial layer and the upper rock layer. On the other hand, in four cases of filter media in the ditch, it was analyzed that the penetration efficiency and the hydraulic interference effect indicated excellent injection performance when a filter medium of 10 to 30 mm diameter was filled in the ditch. In addition, the proper spacing of the injection wells was analyzed as 9~12 m considering the interference efficiency. The interference efficiency attenuation coefficient per 1 m of hole spacing was calculated to be 1.75% in this area. In the future study, the artificial recharge design factors obtained in this stage are applied and verified on site construction and operation. Also it is expected to contribute to securing water in areas where there is always a lack of water.

• Korean Journal of Optics and Photonics
• /
• v.13 no.4
• /
• pp.363-369
• /
• 2002

We have designed conductive transparent filters using a low-emissivity coating such as [dielectric|Ag|dielectric] for display applications. The design is the repetition of [$TiO_{2}$|Ti|Ag |$TiO_{2}$] to increase the transmittance in the visible and decrease the transmittance in the near IR. The conductive transparent filters are deposited by a radio frequency(RF) magnetron sputtering system. The optical, structural and electrical properties of the filters were investigated and the optical spectra are compared with simulated spectra. The thickness of the deposited Ag films is above 13 ㎚ to increase the conductivity and that of $TiO_{2}$ films is 24 ㎚ to increase the transmittance in the visible range. Ti blockers are employed to prevent the Ag films from being oxidized by an oxygen gas during the reactive sputtering process. Also, it is shown that the thicker Ti film is necessary as the period increases. Finally, a filter with repetition of the basic structure three times shows the better cut-off near infrared(NIR) and the sheet resistance as low as 2Ω/□ which is enough to shield an unnecessary electromagnetic waves for a display panel.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.7
• /
• pp.777-782
• /
• 2011

Micro features on the surface are well-known to have significant effects on optical or mechanical properties such as the optical interference, reflectance at the surface, contact angle, interfacial friction, etc. These surface micro features are increasingly employed to enhance the functionality of the applications in various application areas such as optical components for LCD or solar panel. Diverse surface features have been proposed and some of them are showing excellent efficiency or functionality, especially in optical applications. Most applications employing the micro features need manufacturing process for mass production and the injection molding and roll-to-roll forming, which are typical processes for mass production adopting polymeric materials, may be also preferred for micro patterned plastic product. Since the functionality or efficiency of the surface structures generally depends on the shape and the size of the structure itself or the array of the structures on the surface, it would be very important to replicate the features very precisely as being designed during the molding the micro pattern applications. In this paper, a series of research activities is introduced for roll-to-roll forming of micro patterned film including filling of patterns with UV curable resin, demolding of surface structures from the roll tool, control of surface energy and cure shrinkage of resin and dispose time and intensity of the UV light for curing of UV curable resin.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.128-134
• /
• 2014

Recently, design and construction of street tunnels tend to focus on cost reduction and preservation of nature. Accordingly, research is actively being carried out to quickly detect fires when they occur in tunnels, which have partially closed structures. Among such research, fire detection methods using optical fiber sensors have a wide bandwidth and fast transmission speed, while using light as a medium. Therefore, it does not receive electrical interference and there is almost no loss of information during transmission, while also having little noise as well. In relation to this, a fire monitoring system that can accurately detect the location of fires in real time using shape memory alloy and optical cables was developed in this study. In order to verify the developed method, light loss measurement test was conducted according to indoor temperature changes, while also conducting fire simulation tests by installing test beds in common underground zones with different external environments of temperature and distance. Upon carrying out experiments, the fire monitoring system developed in this study was found to be able to detect fires in long distance sections in real time.

• Korean Journal of Optics and Photonics
• /
• v.8 no.4
• /
• pp.333-339
• /
• 1997

We fabricated a sensor head which consists of spliced different-diameter fiber gratings for discrimination between strain and temperature. Because the fibers were drawn from the same preform, their temperature characteristics were the same but not for strain sensitivities which are inversely proportional to fibers cross-sectional areas. In measurement range of 0-1500$\mu$strain and 20-10$0^{\circ}C$, we could obtain, by using the matrix calculation, the unknown physical quantities within 10% of calculation error compared with the micrometer and thermocouple values. To improve the strain measurement accuracy, we suggest a new, novel method which deploys an unbalanced fiber Mach-Zehnder interferometer. This new signal processing technique converts the strain information to interference signal amplitude variation, temperature-independently. we obtained measurement accuracy nearly 80 times better than that obtainable with the conventional optical spectrum analyzer usage.