• 한국정보통신학회논문지
• /
• 제25권3호
• /
• pp.478-485
• /
• 2021

광 주입 잠금 반도체 레이저의 주입 매개 변수를 조절하여 광학적 복소 신호를 생성 할 수 있다. 그러므로 정확한 주입 매개 변수의 결정은 광학적 복소 신호 생성 기술에서의 핵심 요소이다. 기존의 주입 매개 변수의 추출 이론은 광 주입 잠금 반도체 레이저의 비율 방정식을 사용하며, 이는 locking map 기반의 보간법을 사용하기 때문에 정확한 주입 매개 변수의 추출에 한계가 있다. 이를 해결하기 위하여 비율 방정식의 새로운 해석법을 제안한다. 제안된 해석법은 비율 방정식을 광학적 복소 신호의 생성에 맞게 수정하여 주입 매개 변수를 직접적으로 도출하는 방법이며, 이를 통하여 보간법을 통한 복소 신호 생성 대비 103 배의 오차 감소를 달성하였다.

• Journal of information and communication convergence engineering
• /
• 제8권4호
• /
• pp.457-460
• /
• 2010

we have analyzed tens of Giga pulse signal generation using sideband injection locking scheme. The numerical model for semiconductor lasers under the strong optical injection is based on the Lang's equation and has been extended in order to take into account the simultaneous injection of the multiple sidebands of the current-modulated laser. The numerical simulation results show that the unselected sidebands will affect the optical and RF-spectral characteristics even though the semiconductor laser is locked to the target sidebands.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.218-224
• /
• 1999

It is necessary to improve mechanical and optical properties in the optical disk substrates as the information storage devices with high storage density using short wavelength laser are being developed. Injection compression molding is regarded as the most suitable process to manufacture optical disk substrates with high is regarded as the most suitable process to manufacture optical disk substrates with high dimensional accuracy low residual stresses and superb optical properties In the present study polycarbonate optical disk substrates were fabricated by injection compression molding and the birefringence regarded as one of the most important optical properties for optical disk is measured. The effects of various processing conditions upon the development of birefringence distribution were examined experimentally. It was found that the value of the birefringence distribution were very sensitive to the mold wall temperature history and the variance of the birefringence distribution in the radial direction was affected by the level of the packing and the compression pressure.

• Journal of the Optical Society of Korea
• /
• 제20권6호
• /
• pp.698-703
• /
• 2016

We report a new all-optical flip-flop (AOFF) with a quite simple structure, using optical beating in an injection-locked Fabry-Perot laser diode (FP-LD) with optical bistability. While conventional AOFF methods using an injection-locked FP-LD require additional devices such as secondary FP-LDs or polarization controllers for reset operation, the proposed method can be implemented using only a single commercially available FP-LD with set and reset signals. The optical beating induces intensity fluctuations inside the FP-LD, and releases the locking state to the reset state. Even though we demonstrated the AOFF at 100 Mbit/s, we expect that its operation rate could extend to 10 Gbit/s, according to the limit of the FP-LD's frequency response.

• 소성∙가공
• /
• 제19권5호
• /
• pp.296-304
• /
• 2010

It is still needed to study the effect of process conditions on the final properties of injection-molded parts for producing precision optical products. Especially, the optical anisotropy, i.e., birefringence, is a significant factor to affect the function of many optical components. In the present study we have focused on the effect of holding and compression processes on the birefringence remaining in the transparent disc by examining the gap-wise distribution of birefringence and extinction angle. As a result, two extra birefringence and extinction peaks near the center in thickness direction showed the effect of holding pressure, which came from the flow in packing stage. However, more uniform birefringence distribution than injection-only cases could be found in injection/compression cases. Depends on the process condition even the flow reversal could be found from the distribution of extinction angle. Finally, graphical representation of optical indicatrix was added for better understanding the final structure of injection-only and injection/compression cases.

• Current Optics and Photonics
• /
• 제4권5호
• /
• pp.405-410
• /
• 2020

A new all-optical flip-flop (AOFF) method based on the absorption nulls of an injection-locked Fabry-Perot laser diode (FP-LD) in transverse magnetic (TM) mode is proposed and experimentally demonstrated. For the set and reset operations of the AOFF, injection locking and the destructive minus of beating in transverse electric (TE) mode are used. The absorption nulls on the TM mode are modulated according to the operations, and then non-inverted (Q) and inverted (${\bar{Q}}$) outputs can be obtained simultaneously. Thanks to the use of several absorption nulls, the proposed AOFF can achieve multiple outputs with extinction ratios of more than 15 dB. Even though the experiment is demonstrated at 100 Mbit/s, the results of previous experiments using the injection of a CW holding beam imply that the operation speed can increase to 10 Gbit/s.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.103-107
• /
• 2009

Recently, injection/compression molding process became more popular than ever to produce many transparent optical products of high precision. Especially, optical disk for read/write is the best example. But those optical disks can cause sensorial problems because of high birefringence or deformation from the residual stresses in the media. Therefore, it is necessary to study the effects of various process conditions on the final birefringence structure in injection-only and injection/compression molded disks for producing precision injection-molded products. In the present paper we have focused on the effect of injection, holding and compression processes on the optical anisotropy(i.e. birefringence) remaining in the MOD by examining the gapwise distribution of birefringence and extinction angle. The effect of holding pressure was found to form the inner two birefringence peaks. But the effect of compression pressure on the birefringence distribution was found to make the uniform distribution near the center in the gapwise direction and inversion of extinction angle far from the gate.

• 소성∙가공
• /
• 제21권2호
• /
• pp.126-130
• /
• 2012

Accurate optical texturing of light guide plate over the entire surface area is an important technical issue in LCD TV industry. Injection molding process has the potential to produce large light guide plates having highly efficient optical textures such as micro-prism array. This study is focused on the effect of the degree of replication of the micro texture of the 40" injection molded light guide plates on the overall optical performance of the display panel. Measured replication ratios of the micro-textures formed with three different types of injection molding process were considered in the modeling of prismatic micro segment array. Optical simulation was conducted and results were discussed.

• 소성∙가공
• /
• 제22권1호
• /
• pp.48-53
• /
• 2013

As the adoption of injection molding technology increases, injected-molded optical products require higher dimensional accuracy and optical stability than ever before. In the present study, four kinds of molding methods, i.e., conventional injection molding (CIM), injection/compression molding (ICM), rapid heat and cooling the mold(RHCM) and rapid injection/compression molding (RICM) were selected in order to investigate the optical anisotropy of a 7 inch Light Guide Plate(LGP) by examining the gap-wise distribution of birefringence and the extinction angle. The results indicate that the compression process can decrease flow-induced birefringence over the whole region and that rapid heating can decrease the birefringence level better than conventional molding. In addition, for the combination of compression and rapid heating a reversal flow was detected from the distribution of the extinction angle near the gate.

• 소성∙가공
• /
• 제20권1호
• /
• pp.54-59
• /
• 2011

Optical properties in injection molded plastic lenses for mobile phone camera have been simulated using commercial program, 3D TIMON. Four plastic lenses are being used in mobile phone camera. The quality of photographs taken by mobile phone camera is strongly depends upon optical characteristics of lenses. The variety of optical properties has been investigated according to the injection conditions through the computer simulation. Consequently optimal injection conditions for four lenses have been determined and simulation results of birefringence have been compared with experiments.