• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.8
• /
• pp.727-733
• /
• 2010

Optical tables provide a platform for the establishment and test of measurement systems which use Laser. Therefore, not only static characteristics such as surface flatness, static stiffness and etc. but dynamic response characteristics is very important design parameter. The dynamic stiffness is generally estimated through the modal test, and compliance is used as a representative performance standard. Recently there is an example of defining the dynamic deflection coefficient and using it as a new performance standard of the dynamic stiffness, but it is not generalized yet in industry. In this study, we verify the validity of existing DDC calculus by making an experiment on granite. And for improvement in damping performance of optical tables, we are going to evaluate the effect of fillers on the compliance, then develop an epoxy adhesive based on the result of this experiment.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.9
• /
• pp.961-964
• /
• 2012

This paper presents a sensing system to measure the deflection of a microcantilever in an atomic force microscope. In general, the optical lever method and interferometry are used for the sensing system; however, their size and cost leaves considerable room for improvement. Therefore, we used an optical pickup head whose operating principle is based on the astigmatism of the commercial optical disk drives. The developed sensing system was applied to a laboratory atomic force microscope, and satisfactory results were obtained.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.9
• /
• pp.495-501
• /
• 2000

This paper presents a method to minimize the initial deflection of a multi-layer piezoelectric microactuator without loosing its piezoelectric deflection performance required for light modulating micromirror devices. The multi-layer piezoelectric actuator composed of PZT silicon nitride and platinum layers deflects or buckles due to the gradient of residual stress. Based on the structural analysis results and relationship between process conditions and mechanical properties we have modified the fabrication process and the thickness of thin film layers to reduce the initial residual stress deflection without decreasing its piezoelectric deflection performance. The modified designs fabricated by surface-micromachining process achieved the 77% reduction of the initial deflection compared with that of the conventional method based on the measured micromechanical material properties is applicable to the design refinement of multi-layer MEMS devices and micromechanical structures.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.81-82
• /
• 2012

• ETRI Journal
• /
• v.30 no.2
• /
• pp.282-289
• /
• 2008

We propose a new mini-slot transmission scheme for a passive optical network (PON) in which each customer can be switched either to access mode or to internetworking mode dynamically. In this paper, we present the system implementation (called LAN-PON) as well as the performance of the proposed transmission scheme to illustrate its feasibility and benefits. A mini-slot scheme can rapidly reduce the queuing delay, which increases due to the flooding of the deflected packets in a deflection scheme. We evaluate the impact of mode switching time on the bandwidth gain (throughput) and delay of local area network (LAN) traffic in the LAN-PON with a mini-slot scheme. We also analyze a theoretical delay model of the proposed scheme. The simulation results demonstrate that switching time has an impact on LAN performance, and the average packet delay of the proposed scheme is significantly improved compared to that of the deflection scheme.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.6
• /
• pp.804-812
• /
• 2003

This paper introduces optical methods for in-situ measurement of surface temperature and pressure transient in thermal processes having nanosecond time scales. In the temperature measurement, a p -Si thin film whose refractive index is calibrated as a function of temperature is embedded beneath the sample surface and the photothermal reflectance is monitored for estimating the surface temperature. The pressure transients are measured using the photoacoustic optical deflection method. The experimental technique is used to analyze the nanosecond laser induced vaporization process that is central to numerous engineering and bio-medical applications. Based on the experimental results, discussions are made on the experimental technique and the physical mechanisms of laser-driven explosive vaporization phenomena.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.1906-1914
• /
• 2012

In this paper, relative service differentiation in JET based optical burst-switched networks with deflection routing is presented. It differs from conventional schemes in that it tries to make the loss rate of high class bursts as low as possible while maintaining the desired proportional ratio between the high class bursts and low class bursts. Strategies applied to it are dynamic wavelength allocation and the preemption which are combined to deflection routing. With dynamic wavelength allocation, the number of wavelengths allocated to high class bursts are dynamically changed. Preemption which gives more preference to high class bursts is also applied to decrease its loss rate. To lower the loss rate, deflection routing is applied for any kind of traffic. With those strategies, the suggested scheme shows desired properties that the loss rate of high class traffic is as lowered as possible. A queueing model for the scheme is developed to approximate loss ratio and the numerical results show that the proposed scheme provisions relative service differentiation.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.07a
• /
• pp.215-216
• /
• 2008

Electricity unified field is described based on magnetic theory. Maxwell Einstein Lorentz Equation & pair particle photon model was introduced for Photonics. Refractive index is calculated as deceleration and deflection of photon due to photo-induced surface magnetism. MEL equation was proved with magneto-jet assumption.

• Proceedings of the Optical Society of Korea Conference
• /
• 1998.08a
• /
• pp.170-171
• /
• 1998

Here are proposed the tunable laser for optical memory which uses the acousto-optic deflector. This laser includes the acousto-optic deflector in the Littrow mount configuration so that we may control the beam deflection by means of the induced RF. Consequently, we can achieve the higher speed and accuracy to compare with the Littrow monut configuration only.

• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.523-530
• /
• 2014

Machine material and structural strain are critical factors for appraising mechanical properties and safety. Particularly in three and four-point bending tests, which appraise the deflection and flexural strain of an object due to external force, measurements are made by the crosshead movement or deflection meter of a universal testing machine. The Digital Image Correlation (DIC) method is one of the non-contact measurement methods. It uses the image analyzing method that compares the reference image with the deformed image for measuring the displacement and strain of the objects caused by external force. Accordingly, the advantage of this method is that the object's surface roughness, shape, and temperature have little influence. However, its disadvantage is that it requires extensive time to compare the reference image with the deformed image for measuring the displacement and strain. In this study, an algorithm is developed for DIC that can improve the speed of image analysis for measuring the deflection and strain of an object caused by a three-point bending load. To implement this algorithm for improving the speed of image analysis, LabVIEW 2010 was used. Furthermore, to evaluate the accuracy of the developed fast correlation algorithm, the deflection of an aluminum specimen under a three-point bending load was measured by using the universal test machine and DIC measurement system.