• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.563-566
• /
• 1988

A current-controlled CMOS operational transconductance amplifier(OTA), whose transconductance is directly proportional to the DC bias current, has been developed for many electronic circuit applications. It features that its transconductance is insensitive to temperature unlike that of the bipolar OTA. This property makes it possible to use the proposed OTA as a basic buliding block in electrically variable circuit design. The SPICE simulation shows that the conversion sensitivity of the circuit is 44.62 mv /${\mu}A$ and the linearity error less than 0.54 % over a bias current range from 2 ${\mu}A$ to 120 ${\mu}A$ when the output is loaded with a 1${\Omega}$ resistor.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권1호
• /
• pp.59-65
• /
• 1997

In this paper, a feedforward amplifier with error correction is designed and implemented. This amplifier is composed of operational amplifier, the performance of which is compared with that of the reference amplifier without feedforward error correction. As a result, the sec¬ondary harmonics level is improved about 10 [dB]. Therefore it is shown that the proposed feedforward amplifier network is to be adopted able for wide - band amplifiers.

• Transactions on Electrical and Electronic Materials
• /
• 제2권4호
• /
• pp.1-6
• /
• 2001

In this paper, a 1.5 V high-gain high-frequency CMOS complementary operational amplifier is presented. The input stage of op-amp is designed for supporting the constant transconductance on the Input stage by consisting of the parallel-connected rail-to-rail complementary differential pairs. And consisting of the class-AB rail-to-rail output stage using the concept of elementary shunt stage and the grounded-gate cascode compensation technique for improving the low PSRR which was a disadvantage in the general CMOS complementary input stage, the load dependence of open loop gain and the stability of op- amp on the output load are improved, and the high-gain high-frequency operation can be achieved. The designed op-amp operates perfectly on the complementary mode with the 180° phase conversion for a 1.5 V supply voltage, and shows the DC open loop gain of 84 dB, the phase margin of 65°, and the unity gain frequency of 20 MHz. In addition, the amplifier shows the 0.1 % settling time of .179 ㎲ for the positive step and 0.154 ㎲ for the negative step on the 100 mV small-signal step, respectively, and shows the total power dissipation of 8.93 mW.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 춘계학술대회
• /
• pp.678-681
• /
• 2009

본 논문에서는 자체 바이어스가 되는 Folded Cascode CMOS OP Amp를 이용하여 싱글 픽셀 포톤 계수기 회로를 설계하였다. 전압 바이어스 회로가 필요 없으므로 싱글 픽셀의 레이아웃 면적을 줄이고 전류 소모를 줄일 수 있다. 매그나칩 반도체 $0.18{\mu}m$ CMOS 공정을 이용하여 설계된 CSA(Charge Sensitive Amplifier)의 신호 전압은 이론치인 151mV이 근접한 138mV로 simulation되었다. 그리고 싱글 픽셀의 레이아웃 크기는 $100{\mu}m{\times}100{\mu}m$이다.

• 전기의세계
• /
• 제29권12호
• /
• pp.798-803
• /
• 1980

A computer program for noise analysis of the audio circuit is developed. The application of the program to the equalizer, low frequency amplifier of radio circuit and cascaded amplifier show good results. The general noise analysis method for cascade operational amplifier is presented. The noise spectral power density is calculated for a resonator active filter.

• ETRI Journal
• /
• 제31권2호
• /
• pp.234-236
• /
• 2009

We present a novel operational amplifier preset technique for a switched-capacitor circuit to reduce the acquisition time by improving the slewing. The acquisition time of a variable gain amplifier (VGA) using the proposed technique is reduced by 30% compared with a conventional one; therefore, the power consumption of the VGA is decreased. For additional power reduction, a programmable capacitor array scheme is used in the VGA. In the 0.13 ${\mu}m$ CMOS process, the VGA, which consists of three-stages, occupies 0.33 $mm^2$ and dissipates 19.2 mW at 60 MHz with a supply voltage of 1.2 V. The gain range is 36.03 dB, which is controlled by a 10-bit control word with a gain error of ${\pm}0.68$ LSB.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(5)
• /
• pp.185-188
• /
• 2001

This paper proposes an error amplifier circuit using OTA(Operational Transconductance Amplifier) which is the main constituent element in pulse width modulation circuit. The proposed OTA error amplifier circuit is featured by simple circuit configuration, excellent high frequency characteristics and bias current controlled output. Through the experiment of pulse width modulation circuit, the validity of the operation of the OTA error amplifier circuit is verified.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.517-520
• /
• 2002

This paper has been studied Operational Amplification Circuit that has high power specification of 90 W is designed. In the input differential amplifier stage, the current source for circuit bias is designed to protect device from high voltage source. the criving state has the voltage gain more than input differential stage. With temperature compensation design, output stage works stable in different to temperature.

• 전자공학회논문지B
• /
• 제30B권7호
• /
• pp.42-49
• /
• 1993

In this paper, switched-capacitor building block presented which are suitable for implementation in GaAs MESFET technology. They include a current source, a gain stage, and an operational amplifier. Switched-capacitor design techniques are discussed that minimize filter sentsitivity to finite gain of the GaAs operational amplifier. Simulation results are presented on third-order elliptic lowpass ladder filter at a sampling rate of 5GHz.

• 전자공학회논문지
• /
• 제53권1호
• /
• pp.59-67
• /
• 2016

저가, 광대역, 그리고 넓은 이득 제어 범위를 갖는 전자 계측 시스템을 실현하기 위한 완전-차동 선형(fully-differential linear operational transconductance amplifier : FLOTA)를 사용한 새로운 계측 증폭기(instrumentation amplifier : IA)를 설계하였다. 이 IA는 한 개의 FLOTA, 두 개의 저항 그리고 한 개의 연산 증폭기(operational amplifier : op-amp로 구성된다. 동작 원리는 FLOTA에 인가되는 두 입력 전압의 차가 각각 동일한 차동 전류로 변환되고 이 전류는 op-amp의 (+)단자의 저항기와 귀환 저항기를 통과시켜 단일 출력 전압을 구하는 것이다. 제안한 IA의 동작 원리를 확인하기 위해 FLOTA를 설계하였고 상용 op-amp LF356을 사용하여 IA를 구현하였다. 시뮬레이션 결과 FLOTA를 사용한 전압-전류 특성은 ${\pm}3V$의 입력 선형 범위에서 0.1%의 선형오차와 2.1uA의 오프셋 전류를 갖고 있었다. IA는 1개의 저항기의 저항 값 변화로 -20dB~+60dB의 이득을 갖고 있으며, 60dB에 대한 -3dB 주파수는 10MHz이였다. 제안한 IA의 외부의 저항기의 정합이 필요 없고 다른 저항기로 오프셋을 조절할 수 있는 장점을 갖고 있다. 소비전력은 ${\pm}5V$ 공급전압에서 105mW이였다.