• 한국추진공학회지
• /
• 제16권5호
• /
• pp.58-66
• /
• 2012

기술 수준에 의해 그 우위가 결정되는 현대 전장에서 항공기 플룸과 복사저부가열은 항공기의 생존성에 관련된 중요한 요인이다. 항공기의 생존성을 향상시키기 위해서는 저부가열, 그리고 항공기 플룸으로부터 방사되는 IR 신호가 감소되어야 한다. 본 연구에서는 IR 신호와 복사저부가열 특성을 고도 5km에서 마하수 0.9와 1.6의 조건으로 설정하여 플룸 내 유동 및 열복사 특성을 고찰하였다. 이를 통해 플룸에서의 IR 신호는 $H_2O$와 $CO_2$의 영향으로 인한 높은 방사특성을 확인하였다. 그리고 마하수가 높고 거리가 가까울수록 저부면에서의 복사열유속이 증가됨을 확인하였다.

• 한국군사과학기술학회지
• /
• 제23권6호
• /
• pp.639-649
• /
• 2020

Air data systems measure airspeed, pressure altitude, angle of attack and angle of sideslip. These measurements are essential for operating flight control laws to ensure safe flights. Since the loss or corruption of air data measurements is considered as catastrophic, a high level of operational reliability needs to be achieved for air data systems. In the case of unmanned air vehicles, failure of any of air data sensors is more critical due to the absence of onboard pilot decision aid. This paper presents design of a dual redundancy air data system and the integration process for an unmanned air vehicle. The proposed dual-redundant architecture is based on two independent air data probes and redundancy management by central processing in two independent flight control computers. Starting from unit testing of single air data sensor, details are provided of system level tests used to meet overall requirements. Test results from system integration demonstrate the efficiency of the proposed process.

• 대기
• /
• 제15권3호
• /
• pp.149-153
• /
• 2005

A balloon-borne Optical Particle Counter (hereafter "OPC Sonde"), which was developed by the atmospheric research group of Nagoya University, is used for getting the information of vertical profile of particle size and concentration in Anmyeon ($36^{\circ}32^{\prime}N$ $126^{\circ}19^{\prime}E$) on 18 March 2005. A range of five different particle sizes is shown in the vertical profile of aerosol number density estimated from the OPC Sonde. It was found that small size particles have vertically larger aerosol number density than relatively big ones. For all size ranges the vertical aerosol number density shows a decreased pattern as the altitude becomes higher. The aerosol number density of $0.3{\sim}0.5{\mu}m$, $0.5{\sim}0.8{\mu}m$, $0.8{\sim}1.2{\mu}m$ size ranges at the 10km height, which is the tropopause approximately, are $1,000,000ea/m^3$, $100,000ea/m^3$, $10,000ea/m^3$ respectively. The data of OPC Sonde are also compared with the data of PM10 $\beta$-ray) and Micro Pulse Lidar which are operating at Korea Global Atmosphere Watch Observatory in Anmyeon.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2004년도 Proceedings of ISRS 2004
• /
• pp.512-514
• /
• 2004

The Electro-Optical Camera (EOC) is a high spatial resolution, visible imaging sensor which collects visible image data of the earth's sunlit surface and is the primary payload on KOMPSAT-l. The purpose of the EOC payload is to provide high resolution visible imagery data to support cartography of the Korean Peninsula. The EOC is a push broom-scanned sensor which incorporates a single nadir looking telescope. At the nominal altitude of 685Km with the spacecraft in a nadir pointing attitude, the EOC collects data with a ground sample distance of approximately 6.6 meters and a swath width of around 17Km. The EOC is designed to operate with a duty cycle of up to 2 minutes (contiguous) per orbit over the mission lifetime of 3 years with the functions of programmable gain/offset. The EOC has no pointing mechanism of its own. EOC pointing is accomplished by right and left rolling of the spacecraft, as needed. Under nominal operating conditions, the spacecraft can be rolled to an angle in the range from +/- 15 to 30 degrees to support the collection of stereo data. In this paper, the status of EOC such as temperature, dark calibration, cover operation and thermal control is checked and analyzed by continuously monitored state of health (SOH) data and image data during the mission life of 3 years. The aliveness of EOC and operation continuation beyond mission life is confirmed by the results of the analysis.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.627-630
• /
• 2009

이젝터 시스템은 주유동 제트에 발생되는 전단 응력과 압력차에 의해 흡입 챔버 압력에 영향을 미치거나 이차 흡입 유동을 유도한다. 이젝터는 터빈 기반 복합사이클 추진기관 및 로켓엔진의 고고도 모사 설비, 압력회복장치, 담수화 시스템, 이젝터 램젯시스템과 같이 많은 분야에 적용되어 널리 사용된다. 본 연구에서는 아음속 및 음속 조건에서 작동하는 이젝터의 형상 및 운전 조건을 결정하는 설계 절차를 수립하고자 하였다. 또한, 이론적 방법과 시험적 연구를 통해 축소 확대 디퓨저가 장착된 이젝터의 작동 특성을 파악하였다. 결국, 수치해석을 통해 요구 성능을 만족하는 이젝터의 최적 형상을 결정하였으며 다양한 노즐 목 및 챔버 직경을 변화시킨 이젝터에 대한 성능 시험을 통해 계산 결과를 검증하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.573-577
• /
• 2009

초음속제트 엔진의 동적거동 모사를 수행하고 흡입구에서의 버즈 마진 확보와 추력 제어를 위한 PI 제어 알고리즘을 연구하였다. 먼저 연료유량 제어를 통해 요구추력을 추종하고 노즐 목 면적 제어를 통해 흡입구에서의 버즈마진이 항상 양의 수를 갖도록 흡입구 출구 압력을 조절하였다. 비행 마하 수, 고도, 받음각 변화에 따라 추력제어와 버즈 마진 제어를 위한 비례 게인과 적분 게인을 각각 구하고 시뮬레이션 하였다. 그 결과 비행 마하 수 2.1에서 3.0, 받음각 $0^{\circ}$에서 $10^{\circ}$ 사이의 운용영역에서 제어목표를 만족함을 확인하였다.

• 대한기계학회논문집A
• /
• 제41권9호
• /
• pp.897-904
• /
• 2017

광학 탑재 장비는 다수의 광학 부품 및 검출기로 구성되며 목표물 탐지와 분류를 목적으로 항공기, 전차 및 군함에 탑재되어 운용된다. 수 km 고도에서 운용되는 항공용 광학 탑재 장비는 항공기에서 발생하는 진동 때문에 구조 안정성과 광학 성능 저하가 발생한다. 설계 단계에서 진동 환경조건에 대한 탑재 장비의 구조 안정성 및 광학 성능 검증이 요구된다. 본 연구에서는 진동 환경조건을 시험 표준 규격서와 항공기에서 발생하는 진동을 측정하여 분석하였다. 진동 환경조건은 구조 안정성 검증을 위한 내구도 진동조건과 광학 성능 검증을 위한 운용 진동조건으로 구분하였다. 구조 안정성을 고유진동수 해석, 내구도 진동 응답해석 및 정해석을 통해 검증하였다. 광학 성능을 운용 진동 응답해석 결과를 광학 설계/분석 프로그램에 적용하여 검증하였다.

• Journal of Positioning, Navigation, and Timing
• /
• 제4권1호
• /
• pp.1-7
• /
• 2015

In the case of an unmanned aerial vehicle (UAV) equipped with a GNSS sensor, a boundary line where the vehicle can actually exist can be calculated using a navigation error model, and safe navigation (e.g., precise landing and collision prevention) can be supported based on this boundary line. Therefore, for the safe operation of UAV, a model for the position error of UAV needs to be established in advance. In this study, the multipath error of a GNSS sensor installed at UAV was modeled through a flight test, and this was analyzed and compared with the error model of an existing manned aircraft. The flight test was conducted based on a scenario in which UAV performs hovering at an altitude of 40 m, and it was found that the multipath error value was well bound by the error model of an existing manned aircraft. This result indicates that the error model of an existing manned aircraft can be used in operation environments similar to the scenario for the flight test. Also, in this study, a scenario for the operation of multiple UAVs was considered, and the correlation between the multipath errors of the UAVs was analyzed. The result of the analysis showed that the correlation between the multipath errors of the UAVs was not large, indicating that the multipath errors of the UAVs cannot be canceled out.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.156-160
• /
• 2007

Ejector system is a device to transport a low-pressure secondary flow by using a high-pressure primary flow. Ejector system is, in general, composed of a primary nozzle, a mixing section, a casing part for suction of secondary flow and a diffuser. It can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejector system is simple in construction and has no moving parts, so it can not only compress and transport a massive capacity of fluid without trouble, but also has little need for maintenance. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an applicable model and operating conditions for an ejector in the condition of sonic and subsonic, which can be extended to the hydrogen fuel cell vehicle. Experimental and theoretical investigation on the sonic and subsonic ejectors with a converging-diverging diffuser was carried out. Optimization technique and numerical simulation was adopted for an optimal geometry design and satisfying the required performance at design point of ejector for hydrogen recirculation. Also, some sonic and subsonic ejectors with the function of changing nozzle position were manufactured precisely and tested for the comparison with the calculation results.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.256-259
• /
• 2008

Ejector system is a device to transport a low-pressure secondary flow by using a high-pressure primary flow. Ejector system is, in general, composed of a primary nozzle, a mixing section, a casing part for suction of secondary flow and a diffuser. It can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejector system is simple in construction and has no moving parts, so it can not only compress and transport a massive capacity of fluid without trouble, but also has little need for maintenance. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an applicable model and operating conditions for an ejector in the condition of sonic and subsonic, which can be extended to the hydrogen fuel cell vehicle. Experimental and theoretical investigation on the sonic and subsonic ejectors with a converging-diverging diffuser was carried out. Optimization technique and numerical simulation was adopted for an optimal geometry design and satisfying the required performance at design point of ejector for hydrogen recirculation. Also, some ejectors with a various of nozzle throat and mixing chamber diameter were manufactured precisely and tested for the comparison with the calculation results.