• Journal of the Korean Society of Combustion
• /
• v.16 no.3
• /
• pp.1-11
• /
• 2011

The main objective of this paper is to investigate characteristic of steam reformer at various geometries and operating conditions. In this paper, the steam reforming is studied by a numerical method and three dimensional simulations were used for effective analytical study. User - Defined Function (UDF) was used to simultaneously calculate reforming and combustion reaction. And the numerical model is validated with experimental results at the same operating conditions. In order to understand the relationship between operating conditions such as gas hourly space velocity(GHSV), mass flow rate of combustor inlet, various numerical investigations are carries out for various geometries. Numerical results show that cylindrical geometry is more effective than rectangular geometry for heat transfer to reactors and reforming efficiency. As mass flow rate of combustor inlet increase, reaction occurs more faster and temperature increase with each geometry. On the other hand, reaction and hydrogen conversion decrease as mass flow rate of reactor decreases.

• Journal of Korean Society on Water Environment
• /
• v.20 no.1
• /
• pp.86-92
• /
• 2004

Lab-scale experiments have been carried out to investigate ammonia stripping with a modified spray tower for removing ammonia nitrogen from swine wastewater. The operating conditions such as initial pH, temperature, air flow, hole size of distributor determining the diameter of water drops, and influent solids concentration were closely examined focusing on removal efficiency of ammonia. As a result of the experiment, in order to achieve high rate of ammonia removal by the air stripping system, the air flow rate must be supplied at high rate with sufficiently high initial pH, temperature. The optimum operating condition to meet the residual ammonia concentration of 300 mg/L was the initial pH of 11.0 at $35^{\circ}C$ with the air flow rate of 20 L/min. It also showed that the smaller hole size is, the higher removal rate of ammonia is expected. However, when used a small sized distributor (2 mm), the flooding problem at the upper column occurred due to clogging of the hole. With regard to the influent solids concentration, it was showed that the lower concentration of solids, the higher removal rate of ammonia. The removal of particulate materials in influent led to improve the removal efficiency of ammonia, rather than to control the operating condition including initial pH, temperature, and air flow. The empirical correlation between KLa and operating parameters would be driven as, $K_{La}=(0.0003T-0.0047){\cdot}G^{0.3926}{\cdot}L^{-0.5169}{\cdot}C^{-0. 1849}$. The calculated $K_{La}$ from proposed formula can be used effectively to estimate the optimum reaction time and to calculate the volume of modified spray tower system.

• Tribology and Lubricants
• /
• v.39 no.4
• /
• pp.123-132
• /
• 2023

In this study, the expansion, stress, and operating clearance of bearing elements during operation are observed using the inner/outer ring temperature test data of a 3.0×10⁶ DN-class roller bearing. The operating clearance characteristics of inner-/outer-ring cooling (IORC) bearings are compared to those of inner-ring cooling (IRC) bearings. For IRC bearings, the thermal expansion of the outer ring is the most important factor in clearance variation. As a result, the operating clearance is less than the initial clearance of 61 ㎛, and the operating clearance decreases to 0.5 ㎛ at 25,500 rpm. Conversely, the temperature of the outer ring of IORC bearings is lower than that of IRC bearings, so the operating clearance is kept smaller. When the coolant flow rate to the outer ring is approximately 1.5 to 2.0 L/min, the temperature difference between the inner and outer rings is minimized and the operating clearance is maintained at a significantly lower level than IRC bearings. Small operating clearances are expected to be effective in reducing cage slip and skid damage in roller bearings. The results and analysis procedures of this study can be utilized to design of bearing clearance, lubricant flow rate, and assembled interference in the early design stage of aerospace roller bearings.

• Proceedings of the Society of Korea Industrial and System Engineering Conference
• /
• 2002.05a
• /
• pp.189-194
• /
• 2002

As a environment of SCM is issued recently, many enterprises are concerned about inventory control for an efficiency of operation and reliablity. The goal of them is to match up to improving of facilities and redoing of inventory cost. To put an efficiency in the operation rate of facilites, A moderate provision of spare parts for that would come into a matter. This study designs two-echelon spare parts distribution system and sees over the relationship between operating rate and inventories of spare parts. and then it determines fitting inventories and investment cost considering an operating rate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.5
• /
• pp.474-481
• /
• 2023

This paper is an experimental study on the optimal operating conditions of direct charging type electrospray for particulate matter collection. To perform the research, a direct charging type electrospray visualization system was configured to photograph the spray shape of microdroplets, and experiments were performed with varying electrode distance, flow rate, and applied voltage, which are the main factors affecting the particulate matter collection efficacy. Through image processing, the total number of microdroplets according to each condition was analyzed, and the number of microdroplets with a diameter of 1.5 mm or less was confirmed. In addition, by calculating the number of microdroplets per power consumption according to the applied voltage, the optimal operating conditions were derived in terms of energy consumption efficacy, and the microdroplet size distribution was analyzed under the optimal operating conditions. As a result of the experiment, it was confirmed that the optimal operating condition was at a flow rate of 10 mL/min and a voltage of -20 kV in case of 5 mm electrode distance, and at a flow rate of 15 mL/min and a voltage of -30 kV in case of 100 mm electrode distance.

• Journal of Applied Reliability
• /
• v.18 no.1
• /
• pp.1-7
• /
• 2018

Purpose: Maintaining appropriate operational availability (Ao) is a key element of combat victory, but estimates vary according to estimation methods. The purpose of this study is to improve the accuracy of estimating operational availability by tracing the changes of the weapon system's failure rate, repair rate, and the level of logistic support. Methods: In order to track the change in the operating availability, the MDT (mean down time) is modeled by adding the repair time and the ALDT (administration and logistic delay time) to the service time. Results: Using the field data of the weapon system A operated by the ROKAF, the failure rate follows a non-homogeneous Poisson process that changes with time, and it is modeled considering the changing repair rate and the logistic support time. Conclusion: The accuracy of the analytical results was verified by comparing the actual operating data with the estimated availability. The results of this study can be used to track and evaluate the availability in a realistic situation where the failure rate and maintenance rate continuously change in operating environment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.11 no.3
• /
• pp.31-44
• /
• 1987

Nowadays, the problems of energy and environmental pollution become serious day by day and the diesel engine, which has been proved to be superior to gasoline engine with respect to fuel consumption and ecological problems of exhaust gas, has been adopted widely for various purposes from the marine diesel engine and the dynamo engine to all kinds of engine on land. Therefore, extensive parametric studies on combustion of diesel engine should be done for its desing and improvement. To predict the behavior of diesel engien according to variable operating conditions by means of cycle simulation, the reasonable pattern of heat release rate has to be asumed. But it is necessary to know the actual variation of heat release rate in order to assume the reasonable pattern of heat release rate according to the actual operating conditions. In this paper, on a high speed small bore diesel engine with pre-combustion chamber, experimental investigations were carried out to determine the relationship between the heat release pattern and parameters such as engine load and speed. And also, the theoretical investigations about the performance variations of the above diesel engine according to the predicted pattern of heat release rate variation were performed. From the above observations, it may be said that the Fanboro indicator, which was used to get the cylinder pressure, can be used to estimate a reasonable pattern of heat release rate and it is confirmed that the pattern of heat release rate for the pre-combustion type engine is different from that of the direct injection type engine.

• Journal of Environmental Science International
• /
• v.31 no.12
• /
• pp.1061-1068
• /
• 2022

The purpose of this study was to develop a recycling system for ozone off-gas. Although the ozone transmission rate of the injector method differs slightly depending on the ozone injection rate, it reaches approximately 99%, which is very high. During the increase in water inflow to the ozone recycling system from 2 L/min to 10 L/min, the average ozone recycling rate was 99.4% at a 1 ppm ozone injection rate, 98.6% at a 2 ppm ozone injection rate, 98.1% at a 3 ppm ozone injection rate. Ozone treatment facility operating costs can be divided into the costs of pure oxygen production, ozone production, and maintenance. The annual operating costs of ozone treatment facilities in Korea are estimated to be approximately 38.9 billion won. The annual savings are estimated to be approximately 5.8 billion won when the ozone transfer rate of the diffuser method, which is mostly employed in domestic water treatment plants, is 85% and 15% of the ozone is recycled.

• Transactions of the Korean hydrogen and new energy society
• /
• v.1 no.1
• /
• pp.24-30
• /
• 1989

Prototype metal hydride chemical heat pump was constructed using $LaNi_{4.7}Al_{0.3}$ for high temperature hydride and $MmNi_{4.15}Fe_{0.65}Al_{0.2}$ for low temperature hydride, and the effects of operating conditions on the performace of heat pump were investigaed to find out the optimum operating condition. Operating variables considered in this work were cycling time, temperature of hot air blown to the high temperature reactor, the amount of hydrogen gas with which the system was charged initially, and the flow rate of air at both reactors. Power of heat pump increases monotonically as $T_h$ increases, and shows maxima at 4.8H/M and 15-25 min in $H_2$ charged and cycling time respectively. Power of heat pump increases as air flow rate increases at low flow rate, but saturates to some value confined by heat flow rate through the hydride bed, These all phenomena can be explained by the modified power equation.

• Journal of Global Scholars of Marketing Science
• /
• v.19 no.2
• /
• pp.40-52
• /
• 2009

Franchising is one of the fastest growing types of business. It is already popular and well-known in the U.S., and has been growing in many other countries including Korea. Furthermore, many Korean franchising companies have expanded their business overseas actively. According to the data by the Ministry of Industry and Resource, 82 companies out of a sample of 500 franchising companies are already operating in many foreign countries and 48% of them have started their foreign business since 2006. This clearly indicates the fast growing current trend of foreign operation by Korean franchising companies. In spite of the fast growing trend of foreign expansion in the industry, academic research on internationalization of franchising companies is extremely difficult to find. Accordingly, academic research on the issue is necessary and urgent in Korea. Among the various research questions on internationalization of franchising business, this study intends to investigate the difference in organizational factors between the franchising companies doing foreign operation and those doing business only domestically. More specifically, this research has the following purposes. First, considering the lack of theoretical basis of previous studies, resource-based theory and agency theory are employed as the theoretical bases. Second, this study explains the difference in internationalization based on organizational factors such as company size, history and growth rate. Third, the five hypotheses regarding the difference in organizational factors are presented and tested empirically, which is the first attempt in the area of this topic. Finally, the study attempts to clarify the conflicting implications among theories regarding some organizational factos such as growth rate. As the theoretical background, resource-based theory and agency theory are discussed. According to resource-based theory, a firm can grow continuously when it has competence and resource, and also the ability to develop them. The competence and resource can include capital, human resource, management skill, market information, ability to manage risk, etc. Meanwhile, agency theory views the relationship between franchisor and franchisee as an agency relationship. In agency theory, bonding capability and monitoring capability are the two key factors which promote internationalization of franchising companies. Based on the two theories, a conceptual model is designed. The model consists of two groups of variables. One is organizational factors including size, history, growth rate, price bonding and geographic dispersion. The other is whether a franchising company is operating overseas or not. We developed the following five research hypotheses basically describing the relationship between organizational factors and internationalization of franchising companies. H1: The size of franchising companies operating overseas is larger than that of franchising companies operating domestically. H2: The history of franchising companies operating overseas is longer than that of franchising companies operating domestically. H3: The growth rate of franchising companies operating overseas is higher than that of franchising companies operating domestically. H4: The price bonding of franchising companies operating overseas is higher than that of franchising companies operating domestically. H5: The geographic dispersion of franchising companies operating overseas is wider than that of franchising companies operating domestically. Data for the analyses are obtained from 2005 Korea Franchise Survey data co-generated by Ministry of Industry and Resource, GS1 Korea, and Korea Franchise Association. Out of 2,804 population companies, 2,489 companies are excluded for various reasons and 315 companies are selected as the final sample. Prior to hypotheses tests, validity and reliability of the measures of size, history, growth rate and price bonding are examined for further analyses. Geographic dispersion is not validated since it is measured using nominal data. A series of independent sample T-tests is used to find out whether there exists any significant difference between the companies internationalized and those operating only domestically for each organizational factor. Among the five factors, size and geographic dispersion show significant difference, growth rate and price bonding do not reveal any difference and, finally, history factor shows conflicting results in the difference depending on how to measure it.