현 도로설계기준은 설계속도에 기반하여 선형설계에 관한 지침을 제시하고 있으며, 이는 설계속도가 도로 공용 후에 운전자의 주행 속도와 거의 동일할 것임을 전제하고 있다. 도로 평면 곡선부의 설계도 주어진 설계속도에 따라 운전자가 쾌적성을 유지한 채 통과할 수 있는 최소곡선반경을 기준으로 제시하고 있다. 그러나 쾌적성에 기초한 횡방향 미끄럼마찰계수는 실제 습윤노면에서 관측되는 물리적인 횡방향 미끄럼마찰계수보다 낮기 때문에 기준에 제시된 곡선반경은 최소의 의미보다는 권장 값으로 보는 것이 합리적이다. 아울러, 최소곡선반경보다 여유로운 설계 값을 선호하는 실무관행으로 도로 공용 후 운전자의 주행속도는 설계속도를 상회하여 설계속도가 주행속도를 대표하지 못하는 결과를 초래하고, 결과적으로 현 설계기준의 주요전제를 위반하게 될 것으로 본다. 이러한 연구 가정을 검토하기 위해 지방부 도로에서 노면 미끄럼 마찰계수와 운전자의 주행속도를 조사하였다. 연구결과로, 쾌적성에 기반한 미끄럼 마찰계수와 물리적인 미끄럼마찰계수와의 차이에 따른 안전여유를 정량적으로 제시했고, 안전여유 및 설계관행에 따른 여유로운 설계로 인해 설계속도와 주행속도 간에 괴리가 발생함을 제시했다. 이를 토대로, 현 설계속도 기반의 선형설계는 최소기준과 더불어 설계속도와 주행속도 사이의 괴리를 최소화할 수 있는 선형 설계 관리 방안이 마련될 필요가 있다.
Financial stability is the foremost prerequisite for the continuous growth and development of hospitals. The present study aimed at developing a deterministic model using the factors which affect the hospitals profitability and at discovering which factor affected the hospital profitability. The study conducted questionnaire surveys on all general hospitals, with the exception of special hospitals, with over eighty hospital beds. Of the 274 subject hospitals, 136 of them, consituting 49.6% of the whole, were used in the study. The results are as follows. 1. In the deterministic model, outpatient revenue was affected more by the number of physician visits than by outpatient service intensity. Inpatient revenue was found to be affected more by the number of discharged patients than by inpatient service intensity. However, the increase rate of the service intensity not only contributed in stepping up the operating margin by $4{\sim}8%$ in outpatient and $3{\sim}6%$ in inpatient, but it was statistically significant. 2. Among the factors which determined the operating cost within the deterministic model, the number of patients had a greater impact on the operating cost than the resource consumption per patient. 3. The resource consumption per patient were proved to have the greatest effect on the profitability within the probabilistic model. The management cost per adjusted patient, in particular, was proven to have a statistically significant effect on the profitability in all hospitals.
Fluctuation of control rod was experienced when plant was operating in normal operation mode in WH type NPPs. In order to cope with increased control rod fluctuation, the lead-lag controller setpoint for rod control system was optimized and resulted in increasing the margin of operation and minimizing unnecessary control rod movement. By optimization of the time constant, the margin of operation was increased by $1.5^{\circ}F$ and the control rod movement was not occurred due to mitigation of temperature fluctuation in loop. According to the mitigation of time constant, the margin of operation was increased but safety margin can be affected badly, so that the influences to FSAR design reference was evaluated. As the result of this evaluation, it satisfied the design reference of the existing safety analysis and was applied to NPP after obtaining the approval.
This paper presents numerical and experimental results of modal parameter identification in a generator stator frame for 500 MW fossil power plants. A commercial finite element analysis S/W was employed for modal analysis. The generator is excited by alternating electromagnetic forces, mainly of 120 Hz in 60 Hz machines, due to magnetic field and electric current in windings. It is necessary to verify that the stator frame has adequate frequency margin from the excitation frequency to avoid possible resonance when operating. Thus, frequency margin required for the stator frame is established using the numerical and experimental results. The results show that the stator frame meets the frequency-margin requirements. Also, results of modal analysis for design modification in order to reduce weights of the stator frame without deteriorating vibration characteristics are presented.
Confluence buffers and single flux quantum (SFQ) switches are essential components in constructing a high speed superconductive Arithmetic Logic Unit (ALU). In this work, we developed a SFQ confluence buffer and an SFQ switch. It is very important to optimize the circuit parameters of a confluence buffer and an SFQ switch to implement them into an ALU. The confluence buffer that we are currently using has a small bias margin of $\pm$11%. By optimizing it with a Josephson circuit simulator, we improved the design of confluence buffer. Our simulation study showed that we improved bias global margin of 10% more than the existent confluence buffer. In simulations, the minimal bias margin was $\pm$33%. We also designed, fabricated, and tested an SFQ switch operating in a DC mode. The mask layout used to fabricate the SFQ switch was obtained after circuit optimization. The test results of our SFQ switch showed that it operated correctly and had a reasonably wide margin of $\pm$15%.
A fuel spiking test was performed to measure the surge margin of gas turbine engines. The surge marin was mainly determined by the compressors and fuel spiking was used to change the operating point in the compressor characteristic map while speed remained constant. To access the surge margin region different spiking signals were applied by modulations of time(frequency) and fuel flow rate(amplitude). The test results showed good agreements with expected fuel spiking patterns and possibility of further studies.
The verification for the design limit margin of the power device for the information communication and surveillance systems using HALT(Highly Accelerated Life Test) reliability test is described. The HALT reliability test performs with a step stress method which change condition until the marginal step in a design and development phase. The HALT test methods are the low temperature(cold) step stress test, the high temperature(hot) step stress test, the thermal shock cyclic stess test, and the high temperature destruct limit(hot DL) step stress test. The power device is checked the operating performance during the test. In this paper, the HALT was performed to find out the design limit margin of the power device.
운전중인 Westinghouse형 원자력 발전소에 디지탈 감시계통을 설치하였을 시의 정량적인 여유도 잇점을 계산하였다. 적용된 발전소는 영광 원자력 1호기 6주기이며 참조한 디지탈 감치계통은 ABB-CE 사의 COLSS이다. 고려된 핵연료 설계제한 한계는 DNBR과 LUCA Fq이다. 평가를 위해 기존 CAOC 한계내에서 200가지의 3-D 출력 분포를 계산하였다. 영광 1호기 6주기의 DNB 관련 가장 제한적인 사고인 CEA 인출사고를 해석하였다. 평가결과 DMS를 설치하면 DNB와 LOCA Fq 관점에서 모두 7%출력 증가 효과를 가져올 수 있을 것으로 나타났다. DMS를 설치하면 PCI 한계도 감시할 수 있다.
Both shifiting the input signal's frequencies by a fixed frequency and compressing the input signal's bandwidth have been known to be effective in improving the stability margin of public adress systems operating in reverberant spaces. This paper describes the effect of an alternative approach of improving the acoustic-feedback stability and yet maintaining speech inteligibility by bandwidth compression and expansion. Conditions are derived for this technizue to be realized and an experimental system has been made - up. A series of experiments has been performed in small spaces and the results have shown that more than 5dB improvement can be obtained in the stability margin.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.