• Journal of the Korean housing association
• /
• v.21 no.1
• /
• pp.113-121
• /
• 2010

This research is aimed at the development of Long Life Housing, which can realize sustainable construction and environment. It also promotes practical use of Long Life Housing with evaluation of the field application through Mockup House. This research is one of the important tools to realize Long Life Housing and deducts various traditional design's element technology to cope with demands of change of life cycle and style of residents. this study set three elements of plans for modernization in the traditional design factors that opening, wall and bottom as space composition elements of interior facts. first, Jang-ji wall and storage wall system separated from elements of wall that applied modernize elements of the wall. second, element of opening was restructure swing-lift-up opening system into modernize. third, maru and toet-maru system separated from elements of bottom that was applied modernize elements of the bottom. each elements segregation with four types as basic type, separate type, movable type and mixed type. This research make a proposal of plans for modernization in the traditional design factors, aimed at Long Life Housing through these four types blend. In addition, it points to promote realization of the sustainable 'Korea-style Long Life Housing' through modernization.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.2
• /
• pp.106-115
• /
• 2002

The performance of an inverter-driven water-to-water heat pump with an electronic expansion valve (EEV) was measured as a function of compressor frequency, load conditions, and EEV opening. Based on the test results, a controller using proportional integral (PI) feedback or PI feedforward algorithm was designed and tested to investigate capacity modulation and transient response control of the system. Although the relation between superheat and EEV opening of the heat pump showed nonlinear characteristics, a control gain obtained at the rated frequency was applicable to various operating conditions without causing large deviations. When the simple PI feedback control algorithm was applied, a large overshoot of superheat and wet compression were observed due to time delay effects of compressor frequency. However, applying PI feedforward control scheme yielded better system performance and higher reliability, compared to the PI feedback algorithm.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.12
• /
• pp.1047-1055
• /
• 2002

The present study is to investigate the pressure wave characteristics and the absorption of the maximum and minimum pressure generated by instantaneous valve closure and opening at the end of the straightening copper Piping system with and without an air chamber. Also, life of air chamber is investigated. Experiments were conducted under the following conditions: initial pressure of 1～5 bar, flow velocity of 0.5～3.0 m/s, water temperature of$20^{\circ}C$ and air chamber volume of 45.1～449.5$cm^3$ The results of the study can be used in sizing air chamber and selecting the water hammer absorbtion apparatus.

• Journal of the Korean Society of Industry Convergence
• /
• v.14 no.3
• /
• pp.113-119
• /
• 2011

This study analyzed facts affecting the performance of refrigeration systems after throttling actions, by changing the amount of refrigerant according to adjusting the opening of manual expansion valve to 80%, or 20% with vapor compressional refrigeration training equipment. At opening of 20%, the inlet and outlet temperature of compressor, subcooling and superheat, condenser heat, refrigeration effect, flash gas heat, coefficient of performance were higher, while at 80%, condensing pressure, evaporating pressure, compression work were higher, Thus, we could see changes in the amount of refrigerant affect the performance of the refrigeration system.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05a
• /
• pp.551-556
• /
• 1997

A present study addresses a loss-of-RHR event as an initiating event under specific low power or shutdown conditions. Two typical plant configurations, cold leg opening case with water-filled steam generators and pressurizer opening case with emptied steam generators, were evaluated using the RELAP5/ MOD3.2 code. The calculation was compared with the experiment conducted at ROSA-IV/LSTF in Japan. As a result, the code was capable of simulating the system transient behavior following the event. Especially, thermal hydraulic transport processes including non-condensable gas behavior were reasonably predicted with an appropriate time step and CPU time. However, there were some code deficiencies such as too large system mass errors and severe flow oscillations in core region.

• Journal of Power System Engineering
• /
• v.19 no.2
• /
• pp.22-26
• /
• 2015

The main objective of this work is to estimate the fluid flow of a proportional valve. The study is based on the classical compressible flow theory and the computations with the help of CFD based commercial software - ANSYS CFX. The fluid flow with the movement of spool along the sleeve is simulated. To change the spool moving from 0.4mm to 2.0mm, the moving mesh method with different condition of orifice is considered here. The results show that it is the highest at the 80 % (1.6mm) opening and at the 20 % (0.4mm) opening, is the lowest.

• 한국전산유체공학회:학술대회논문집
• /
• 2001.05a
• /
• pp.170-175
• /
• 2001

Fire inside light railway transit(LRT) was simulated for various fire scenarios using CFD analysis in order to assess the safety of passengers. Considered in the present paper are the effects of locations of fire, a fire size, an operation of ventilation system and an opening time of door on evolution of temperature and smoke concentration inside the LRT. For fire simulation, fire cells releasing heat and smoke corresponding to fire size were positioned at the location of fire. From the results, it is seen that the ventilation system and the opening time of door were the most important factors on temperature and smoke concentration inside the LRT

• International Journal of Contents
• /
• v.6 no.4
• /
• pp.43-48
• /
• 2010

Because of the social and political reasons, Chinese design higher education has come a long and difficult road. Before and after the Reform and Opening-up, Chinese design higher education system has gone through two different models: "Arts and Crafts" and "Arts & Design". By comparing external environment and Education Concept of two models, this paper points out that the correct direction of design higher education reform is to understand and learn the advantages of two education systems.

• Journal of the Korean Society of Costume
• /
• v.50 no.8
• /
• pp.149-163
• /
• 2000

The purpose of this study is to research the Korean and Japanese costume systems and to compare both of them on the process of adopting the western-originated costumes. The consequences of this study are as follows. Chosen and Japan started simplifying the traditional clothings, Introducing the western clothings and executed the ordinance prohibitory topknots through reforming costume systems since Port Opening Treaties in 19th centra. Japan performed the reformation of costume system effectively through the grand campaign of social reforming enlightment by Meiji Government. Meanwhile in Korea, there were a continual repetition of adoption and rejection in the reformation of costume systems because of strong cultural self-esteem and competition of foreign Empires. However, western-originated cultural perspectives brought the strong self-devaluated view on their own cultures to both countries. And that's the first cause of substitution of western clothings for ordinary ones in both nations.

• Journal of Korea Society of Industrial Information Systems
• /
• v.11 no.1
• /
• pp.7-12
• /
• 2006

In this paper, we develop a control system with fire receiver and emergency light that controls (manages) emergency door by wireless signals which prevents crime but also helps evacuate in (fire) emergency. This automatic door operator can be installed on any buildings which have a problem of opening or shutting emergency doors, and it is especially good for buildings with high fire vulnerabilities such as complex buildings, apartments and multistoried buildings without easy control of rooftop doors.