• 한국산업보건학회지
• /
• 제15권3호
• /
• pp.239-249
• /
• 2005

Ventilation effect is analyzed for boiler building with multiple heat sources. Air flow inside the boiler building is characterized as turbulent mixed convection. Analysis methodology is set up with two different $k-{\varepsilon}$ type models (standard $k-{\varepsilon}$, RNG $k-{\varepsilon}$). Two different cases with high and low outside temperature are analyzed. In case of high outside temperature condition, mixed convection is well realized inside the boiler building. With different upper louver opening rate, air flow is also well established and proper opening rate is found to meet design limit in case of low outside temperature condition. Difference of analysis results for two different turbulence models are not significant. Therefore, analysis methodology with simple $k-{\varepsilon}$ turbulence model is found to be reliable for the boiler building ventilation analysis. However, more simplified geometrical model is desired to expand its application.

• 한국생산제조학회지
• /
• 제19권6호
• /
• pp.883-888
• /
• 2010

This study have goal with conceptual design for Offshore Structures of high pressure control valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the Offshore Structures high pressure control valve. Numerical simulation using CFD (Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the glycerin (C3H8O3). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated until increasing 1bar to 10bar. CFD analysis used STAR-CCM+ which is commercial code and Governing equations were calculated by moving mesh which is rotated 90 degrees when ball valve operated opening and closing in 1 degree interval. The result shows change of mass flow rate according to opening and closing angle of valve, Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. Relation with flow and flow coefficient can not be proportional according to inlet pressure when compare with mass flow rate. Because flow coefficient have influence in flow and pressure difference. Namely, flow can be change even if it has same Cv value. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.

• 한국정보통신학회논문지
• /
• 제9권5호
• /
• pp.1123-1131
• /
• 2005

장거리 $8{\times}40$ Gbps 파장 분할 다중 시스템에서 색 분산과 자기 위상 변조에 의해 왜곡된 광 펄스를 최상으로 보상할 수 있는 최적의 광 위상 공액기 (OPC ; Optical Phase Conjugator)의 위치를 수치적 방법으로 살펴보았고, 이 위치에서의 전체 채널의 눈 열림 패널티 (EOP ; Eye Opening Penalty)와 비트 에러율 (BER ; Bit Error Rate) 특성을 OPC가 전체 전송 거리의 중간에 위치한 경우 (MSSI ; Mis-Span Spectral Inversion)와 비교해 살펴보았다. 먼저 OPC를 이용해 왜곡된 광 신호를 보상하는 WDM 시스템에서 모든 채널의 최상의 보상을 수행하기 위해서는 전송하고자 하는 변조 파형의 형식과 광섬유 분산 계수와 관련하여 OPC의 위치가 전체 전송 거리의 중간이 아닌 다른 곳으로 이동되어야만 하는 것을 확인할 수 있었다. 아울러 최적 OPC 위치를 갖는 WDM 시스템을 이용한 경우 수신측에서의 광 신호의 EOP 특성은 채널에 따라 다소 차이가 있을 수 있지만, BER 특성은 거의 동일하다는 것을 확인할 수 있었다.

• Journal of Preventive Medicine and Public Health
• /
• 제34권3호
• /
• pp.219-227
• /
• 2001

Objectives : To understand the current status of the opening, closing and relocation of primary medical institutes in Korea and identify the underlying decision factors. Methods : Sources of analyzed data included the medical institutional master file at the National Health Insurance Corporation(1998, 2000) and Regional Statistic Annual Bulletins. To investigate changes including the opening, closing and relocation, a total of primary medicalinstitutions(16,757 in 1998, 19,267 in 2000) were analysed. Results : Between 1998 and 2000, there was a 15.0%(2,510) increase in the number of primary medical institutions and the rate of increase in the rural area was higher than the urban area, and higher for specialty clinics than primary practice. However, these findings did not suggestany improvement in the maldistribution of primary medical institutions. During the time period studied, newly opened and closed primary medical institutions numbered 4,085 and 1,573, respectively. Additionally, institutions thatrelocated numbered 2,729, or 16.3% of all primary medical institutions in operation in 1998. These openings and closings were more frequent among young doctors. As a result of our analysis on the underlying regional factors forrelocation, the factors that were statistically significant were local per capita tax burden and the number of schools per ten thousand persons. !n, the case of institutional factors, movements were significantly associated with gender and the location of primary medical institutions. Conclusions : In order to establish effective long-term intervention for primary medical institutions, further study and monitoring of primary medical institutions and the identification of factors influencing opening location and relocation is necessary.

• 한국화재소방학회논문지
• /
• 제27권3호
• /
• pp.20-29
• /
• 2013

실규모 환기부족 구획화재에서 수직 개구부의 형상 및 위치변화에 따른 열 및 화학적 화재특성 변화를 수치적으로 검토하기 위하여, 이론적 최대 공기 유입량을 결정하는 환기인자($A\sqrt{h}$)와 heptane pool 화재의 질량 감소율이 모든 조건에 대하여 동일하게 설정되었다. 주요 결과로서, 출입문 형상의 변화는 구획 내부의 열 및 화학적특성 변화에 큰 영향을 미친다. 창문 위치의 변화는 화재지속시간 및 재순환 유동구조를 포함한 추가적인 화재특성의 복잡한 변화를 초래하였다. 이들 결과는 개구부 유동 및 연료/공기의 혼합현상을 포함한 다차원 유동 및 화재특성을 통해 상세히 분석되었다.

• Computers and Concrete
• /
• 제31권3호
• /
• pp.207-221
• /
• 2023

In this investigation, the interaction between opening space and neighboring joint has been examined by experimental test and Particle flow code in two dimension (PFC2D) simulation. Since, firs of all PFC was calibrated using Brazilian experimental test and uniaxial compression test. Secondly, diverse configurations of opening and neighboring joint were provided and tested by uniaxial test. 12 rectangular sample with dimension of 10 cm*10 cm was prepared from gypsum mixture. One quarter of tunnel and one and or two joint were drilled into the sample. Tunnel diameter was 5.5 cm. The angularities of joint in physical test were 0°, 45° and 90°. The angularities of joint in numerical simulation were 0°, 30°, 60°, -30°, -45°, -60° and its length were 2cm and 4cm. Loading rate was 0.016 m/s. Tensile strength of material was 4.5 MPa. Results shows that dominant type of crack which took place in the model was tensile cracks and or several shear bands develop within the model. The Final stress is minimum in the cases where oriented angle is negative. The failure stress decrease by decreasing the joint angle from 30° to 60°. In addition, the failure stress decrease by incrementing the joint angle from -30° to -60°. The failure stress was incremented by decreasing the number of notches. The failure stress was incremented by decreasing the joint length. The failure stress was incremented by decreasing the number of notches. Comparing experimental results and numerical one, showed that the failure stress is approximately identical in both conditions.

• International Journal of Precision Engineering and Manufacturing
• /
• 제2권3호
• /
• pp.19-26
• /
• 2001

In order to investigate the effect of single tensile overload on the short crack growth behavior under the out-of-plane cyclic bending moment, crack opening stresses were continuously measured by an elastic compliance method using strain gages. The characteristics of short crack growth after the single tensile overload are analyzed by the effective stress range ratio. Futhermore, the investigation was carried out with respect to various fatigue crack growth behaviors such as the plastic zone size effect on crack retardation, the retarded crack length and the number of cycles.

• 동력기계공학회지
• /
• 제19권2호
• /
• pp.22-26
• /
• 2015

The main objective of this work is to estimate the fluid flow of a proportional valve. The study is based on the classical compressible flow theory and the computations with the help of CFD based commercial software - ANSYS CFX. The fluid flow with the movement of spool along the sleeve is simulated. To change the spool moving from 0.4mm to 2.0mm, the moving mesh method with different condition of orifice is considered here. The results show that it is the highest at the 80 % (1.6mm) opening and at the 20 % (0.4mm) opening, is the lowest.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.587-591
• /
• 2011

To improve the performance of the control butterfly valve seals are used to eccentric shaft. In this case, vertical opening gas of the butterfly valve is non-symmetrical, which will change the flow pattern around the valve. In this study, the eccentric drive shaft of the butterfly valve to change flow characteristics are performed numerically. Flow pattern and pressure drop are investigated as the valve opening angle increases for a given mass flow rate. The valve flow coefficient is compared to the without eccentric shaft.

• 제어로봇시스템학회논문지
• /
• 제8권3호
• /
• pp.275-280
• /
• 2002

A new algorithm for gradual scene change detection in MPEG based frame sequences is proposed in this paper. The proposed algorithm is based on the fact that most of gradual curves can be characterized by variance distributions of edge information in the frame sequences. Average edge frame sequences are obtained by performing "sober" edge detection. Features are extracted by comparing variances with those of local blocks in the average edge frames. Those features are further processed by the opening operation to obtain smoothing variance curves. The lowest variance in the local frame sequences is chosen as a gradual detection point. Experimental results show that the proposed method provides 85% precision and 86% recall rate fur gradual scene changes.