• Corrosion Science and Technology
• /
• v.3 no.6
• /
• pp.233-239
• /
• 2004

Primary water stress corrosion cracking of steam generator tubings occur on many tubes in pressurized water reactors(PWRs), and they are repaired using sleeves or plugs. In order to develop proper repair criteria, it is necessary to know the leak behavior of the tubes, which have stress corrosion cracks. Crack development tests were carried out on the tubes at room temperature, and leak rate and burst pressure were measured on the degraded tubes at room temperature and a high temperature. No leakage was detected on the tubes where 100 % through wall crack developed, at 1560 psi, which is an operating pressure difference of pressurized water reactors(PWRs). In some tests, leak rates of the tubes increased with time at a constant internal water pressure. A test tube showed a very small amount of leakage at 2700 psi in a high temperature pressure test at $282^{\circ}C$, but it disappeared after the pressure increased slightly. Even cracks are 100 % through wall, they need to open in order to reach a certain amount of leak rate at the operating pressure difference.

• The Korean Journal of Mycology
• /
• v.14 no.1
• /
• pp.25-30
• /
• 1986

The purposes of this study were to investigate enzyme components and its physiological activities of Sarcodon aspratus (Berk.) S. Ito which grows wildly in Korea, belonging to the family Thelephoraceae. The carpophores of the fungus was extracted with cooling distilled water and salted out by ammonium sulfate. The precipitate was purified by dialysing through visking tube against distilled water and then dissolved with pH 7.8 ammonia aqua, and the extract was filterated. The fraction of filtrate was obtained as light brown powder after lyophilization and determined proteolytic activity. Protease activity of Sarcodon aspratus (Berk.) S. Ito was about two-third of that of pepsin on casein by cup method. The proteolytic potency of this enzyme was found to be 500 unit/mg. This proved the efficacy of the mushroom when it was used as a folk medicine for treating indigestion of beef.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.168-173
• /
• 2003

This experimental study describes the propagation characteristics of the impulse noise emitted from the exit of a perforated pipe attached to the open end of a simple shock tube. The pressure amplitudes and directivities of the impulse wave propagating from the exit of perforated pipe with several different configurations are measured and analyzed fur the range of the incident shock wave Mach number between 1.02 and 1.2. In the experiments, the impulse waves are visualized by a Schlieren optical system for the purpose of investigating their propagation pattern. The results obtained show that for the near sound field the impulse noise strongly propagates toward to the pipe axis, but for the far sound field the impulse noise uniformly propagates toward to the all directions, indicating that the directivity pattern is almost same regardless of the pipe type. Moreover, it is shown that for the far sound field the perforated pipe has little performance to suppress the impulse noise.

• Proceedings of the KIEE Conference
• /
• 1985.07a
• /
• pp.215-218
• /
• 1985

In this paper, The electron drift velocity was measured from an experimental study of the open end heat pipe system by induced current method as alkali metal vapour was generated in ordinary region of a drift tube. The test condition was alkali metal vapour range from 3.6 to 20.1(Torr), temperature of 667 to 755(K), and E/N of $1{\times}10^{-16}$ to $1{\times}10^{-15}(v.cm^2)$. The results of this study were obtained essentially the same as the extrapolated prediction curve for electron drift velocity in the alkali metal Vapour of J. Lucas et 31 with range of E/N: $1{\times}10^{-17}$ to $1{\times}10^{-16}(v.cm^2)$, and the electron drift velocity was obtained the result an increase in alkali to E/N range from E/N $2.8{\times}10^{-17}$ to $5.6{\times}10^{-16}(v.cm^2)$ (E/N From 2.8 to 50 Td).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.481-485
• /
• 2003

To diffuse Zn at solid-state, the $SiO_2/ZnO/SiO_2$ wafers was made by PECVD and RF Spotter. Thicknesses of bottom $SiO_2$ and cap $SiO_2$ was about $500{\AA}$ and about $3500{\AA}$. First test was Diffusion temperatures were $760^{\circ}C$, $780^{\circ}C$, and $800^{\circ}C$, and diffusion times were 1, 2, 3, 4, 5, and 6 hr and 2nd test was Diffusion temperatures were $760^{\circ}C$, $720^{\circ}C$, and $680^{\circ}C$, and diffusion times were 1, 2, 3, 4, 5, and 6 hr. LED chips were fabricated by the diffused wafers at Fab. The peak wavelength of all chips showed about $625{\sim}650\;nm$ and red color Main reason for Iv change was by diffusion temperature not diffusion time. The lower temperature was the higher Iv. We thick that these properties is because of the very high diffusion temperature.

• Nuclear Engineering and Technology
• /
• v.28 no.3
• /
• pp.229-246
• /
• 1996

A mechanistic model has been developed to predict the release behavior of fission gas during steady-state irradiation of LWR UO$_2$ fuel. Under the assumption that UO$_2$ grain surface is composed of fourteen identical circular faces and grain edge bubble can be represented by a triangulated tube around the circumference of three circular grain faces, it introduces the concept of continuous formation of open grain edges tunnels that is proportional to grain edge swelling. In addition, it takes into account the interaction between the gas release from matrix to grain boundary and the reintroduction of gas atoms into the matrix by the irradiation-induced re-solution of grain face bubbles. It also treats analytically the behavior of intragranular, intergranular, and grain edge bubbles under the assumption that both intragranular and intergranular bubbles are uniform in both radius and number density. Comparison of the present model with experimental data shows that the model's prediction produces reasonable agreement for fuel with centerline temperatures of 1000 to 140$0^{\circ}C$, wide scatter band for fuel with centerline temperatures lower than 100$0^{\circ}C$, and underprediction for fuel with centerline temperatures higher than 140$0^{\circ}C$.

• Journal of Chest Surgery
• /
• v.3 no.2
• /
• pp.127-132
• /
• 1970

A patient was 29 year old house wife who was admitted to the Yonsei University Medical Center on 6 th of Nov., in 1970, with chief complaints of complete loss of bilateral visual acuity, generalized weakness, frequent palpitations, claudication of masseter muscles and intermittent fainting. These symptoms were developed 5 years prior to admission. Physical finding on admission revealed complete loss of bilateral visual acuity, absence of both radial and carotid pulse, but there was good femoral and popliteal pulse. She couldn't open her mouth as she desired and had weakness of mastication. Radiological findings of plane chest PA were not significant. Aortogram(Cineangiogram) showed non-visualization of both carotid and subclavian arteries. It showed only innominate and interal mammary artery preoperatively. The operative findings were as follows: There were complete obliterative changes in both common carotid and subclavian arteries, and periarteritis in the innominate artery. Tube Dacron Prosthesis Bypass with V-arm between innominate artery and both common carotid arteries was performed after thromboendarterectomy. Histopathological finding of the thromboend arterectomy specimen was compatible with pulseless disease, which showed marked fibrous thickening of intima and a diffuse inflammatory cell infiltration of the whole layers. Her postopererative course was uneventful. Follow up aortogram(Cineangiogram) was taken on 11th postoperative day, which revealed both common carotid arteries patent. Her preoperative Subjective symtoms disappeared remarkably, such as her visual acuity improved much, fainting and vertigo disappeared completely and she can go to bath room without difficulty and help. Another patient was 34 year old house wife who was admitted on August, 1964 with chief complaints of frequent fainting and progresive visual loss. She was operated only thromboendarterectomy of both common carotid arteries. Postoperative course was smooth and subjective symptoms were disappeared.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.445-445
• /
• 2016

급변하는 개수로 흐름에서 발생하는 바닥전단응력의 분포는 하천구조물 설계에 있어 매우 중요한 요소이다. 하천 구조물 중 호안에 대한 하천설계기준 '설계편 제 24장 호안'에는 호안 설계에 대한 일반적인 사항이 제시 되어 있으나, 구체적인 소류력 또는 유속에 대한 기준, 각 호안공법들의 안정성을 평가하기 위한 시험법 등에 대한 구체적인 기준이 부족한 상황이다. 소류력 측정방법에는 간접측정법과 직접측정법이 있다. 간접측정법에는 Reach-Average공식, Reynolds Stress, TKE공식 (Turbulent Kinetic Energy)이 있고 직접측정법에는 Shear Meter, Preston Tube 등이 있다. 본 연구에서는 바닥전단응력을 직접 측정할 수 있는 1차원 소류력 측정장치를 개발하고, 최대유속 5m/s 가변형 고속수로 실험을 통하여 Reach-Average 공식, Reynolds Stress, TKE 공식으로 산정한 바닥전단응력 값과 1차원 소류력 측정장치 값을 비교 분석하였다. 실험케이스는 총 3개로, 22.42???, 30.00???, 41.00??? 유량을 사류이면서 난류인 상태로 실험을 수행하였다. 분석 결과, 본 연구에서 개발한 1차원 소류력 측정장치의 측정값은 TKE공식과 약 2.3% 차이가 났으며, Reach-Average공식과 약 8.1%, Reynolds Stress는 약 22.1% 차이가 났다. 즉, 본 연구에서 개발한 1차원 소류력 측정장치는 유속 범위(1m/s ~1.6m/s )에서 TKE공식을 이용한 바닥전단 응력과 가장 근사하게 나타나는 것으로 분석되었다.

• Geomechanics and Engineering
• /
• v.18 no.3
• /
• pp.277-289
• /
• 2019

In this study, an innovative anchoring approach has been developed dealing with all relevant aspects in consideration of previous works. An ultimate pulling force calculation of anchor is presented from a geotechnical point of view. The proposed umbrella anchor focuses not only on the friction resistance capacity, but also on the axial capacity of the composite end structure and the friction capacity occurring around the wedge. Even though the theoretical background is proposed, in-situ application requires high-level mechanical design. Hence, the required parts have been carefully improved and are composed of anchor body, anchor cap, connection brackets, cutter vanes, open-close ring, support elements and grouting system. Besides, stretcher element made of aramid fabric, interior grouting system, guide tube and cable-locking apparatus are the unique parts of this design. The production and placement steps of real sized anchors are explained in detail. Experimental results of 52 pullout tests on the weak dry soils and 12 in-situ tests inside natural soil indicate that the proposed approach is conservative and its peak pullout value is directly limited by a maximum strength of anchored soil layer if other failure possibilities are eliminated. Umbrella anchor is an alternative to conventional anchor applications used in all types of soils. It not only provides time and workmanship benefits, but also a high level of economic gain and safe design.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.6
• /
• pp.20-28
• /
• 2021

High enthalpy test facilities, such as a shock tunnel, are to be operated at the specific pressure ratio according to the desired test condition. A metallic diaphragm is machined or a forced rupture device is used to open it at a specific pressure ratio. The diaphragm opening procedure takes several hundred microseconds including rupture and deformation. This process is expected to affect the test conditions. In this study, numerical simulation was performed for different materials, thicknesses, and opening ratios. And the characteristics of shock wave generation and the stagnation condition in the tube are investigated. Results show that the final opening ratio and rupturing procedure directly affect the speed of a shock wave, stagnation pressure, and test time.