• ETRI Journal
• /
• v.30 no.4
• /
• pp.615-617
• /
• 2008

A novel and compact elliptic-function bandpass filter is proposed in this letter. The techniques of slot etching and the addition of open stubs are applied to enhance the self-inductance and self-capacitance of hexagonal open-loop resonators. Thus, size reduction and improved transmission performance are obtained. Compared to the performance of the conventional design, the central frequency and insertion loss are reduced by 28% and 3.1 dB, respectively. Measurements show that the proposed filter has a fraction bandwidth of 23% at the central frequency of 1.84 GHz, and its insertion loss in the passband is less than -1.5 dB. The bandpass filter occupies only 12 mm${\times}$21.2 mm (approximately $0.24{\lambda}_g{\times}0.14{\lambda}_g$).

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.6
• /
• pp.38-47
• /
• 2008

In this paper, the narrow band-pass filter with compact-size using the ${\lambda}g/2$ open stubs is proposed. The filter size is reduced by realization of transmission line at second harmonics and at the same time the power can be transferred to the output by using the fundamental wave generated in the resonator and the transmission line in which the impedance mismatch technique is adopted. Thus, the proposed filter can be reduced to half-length of horizontal transmission line than the conventional one. The experimental results show that insertion loss is 1.58 dB and return loss is 9.86 dB, and the fractional bandwidth is 10 % at the center frequency of 5.8 GHz. The filter size is $10.34{\times}18.56\;mm2$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.6 s.97
• /
• pp.594-602
• /
• 2005

In this paper, a new type of 5-pole low pass filter(LPF) having defected ground structure(DGS) and very wide transmission line elements is proposed. The previously presented design method of 3-stage LPF using DGS is generalized to design N-pole LPFs for $N\geq5$. As an example, a 5-pole LPF having DGS is designed and measured. The accurate curve-fitting method to determine the series inductors in the prototype filter, and ultimately the size of DGS is described. The proposed 5-pole LPF has transmission line elements with a very low impedance to realize the required shunt capacitance instead of open stubs. Therefore, open stub. Therefore, open stub, Tee-junction, Cross-junction, and high impedance line are not required for the proposed LPF, while they all have been essential in conventional LPFs.

• Journal of Navigation and Port Research
• /
• v.30 no.5 s.111
• /
• pp.331-334
• /
• 2006

In this paper, we designed and fabricated the lowpass filter with the wide stopband characteristics using microp- strip line. Adding the $\lambda_g/4$ open stub at the input and output ports, we developed the L-C ladder type lowpass filter using the open stub which has wide stopband characteristics. In order to reduce the entire size qf this filter, the high impedance microstrip lines were made with the meander structure. The lowpass filter was fabricated with the cutoff frequency 2.3 GHz and its measured frequency responses agree well with the simulation results.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.150-154
• /
• 2003

In this letter, a novel compact duplexer which consists of Tx and Rx Filter using microstrip line ${\lambda}/4$ resonators with a pair of tap-connected open-ended stepped impedance stubs is designed. The tapped open stubs not only work as K-inverters but also introduce attenuation poles, attenuation poles are located at upper and lower side of the passband by adjusting the open stub length and width. The result of measurement duplexer has been yielded better isolation and sharper skirt behavior than that with a conventional bandpass filter and similar to those of simulation results.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.2
• /
• pp.67-74
• /
• 2009

In this paper, the multi-band antenna with CPWG(Coplanar Waveguide with Ground) feed for telematics mobile devices is designed and fabricated. The proposed antenna improves the return loss characteristic by using open-circuited stub matching and rectangular slot in the radiation patch. In addition, CPWG structure makes up for the drawback of the CPW which is variation of impedance matching according to the gap variation of the feed line and the ground. The fabricated antenna has 1.4GHz ($1.43GHz{\sim}2.83GHz$, 65%) band width on -10dB (VSWR<2) and the maximum gains are 0.8dBi, 1.34dBi, 2.41dBi, 2.53dBi, 2.6dBi and 1.51dBi on each resonant frequency that are GPS $(1.564GHz{\sim}1.585GHz)$, PCS/DCS $(1.710GHz{\sim}1.984GHz)$, WCDMA $(2.170GHz{\sim}2300GHz)$, Bluetooth/Wi-Fi/WLAN $(2.4GHz{\sim}2.483GHz)$, WiBro $(2.3GHz{\sim}2.4GHz)$, SDMB $(2.605GHz{\sim}2.655GHz)$. It also has an omni-directional radiation pattern of H-Plane.

• Journal of the Korean Institute of Navigation
• /
• v.22 no.1
• /
• pp.15-22
• /
• 1998

In this paper, discontinuity parts in microstrip line with $\lambda$/4 open stub and one in crank type have been anlayzed by using FDTD(Finite-Difference Time-Domain) analysis method. The noise components, in this case, are occred at the discontinuites of the given microstrip lines, the complex poles were extracted by the analysis using GPOF (Generalized Pencil-of Function) method from electric field of time domain. It has, then, been found that the noise level and the noise frequency components included in signal could be derived.

• 한국ITS학회:학술대회논문집
• /
• v.2006 no.10
• /
• pp.175-178
• /
• 2006

• ETRI Journal
• /
• v.34 no.3
• /
• pp.454-457
• /
• 2012

A miniaturized planar digital video broadcasting terrestrial (DVB-T) antenna, which is composed of a patterned helical line, an open stub, and an impedance matching circuit on an FR4 (${\varepsilon}_r$=4.4) substrate for portable media player applications, is presented in this letter. The antenna has monopole-like, omni-directional radiation characteristics and a wide impedance bandwidth (VSWR<3) in the DVB-T band from 174 MHz to 230 MHz at the VHF band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.5
• /
• pp.486-487
• /
• 1997

This paper presents the pure capacitive lumped element equivalent circuits for several coplanar waveguide(CPW) discontinuities such as an open-end, an open-end with connected ground planes, a gap and an open-end CPW stub and gives their capacitive element values as a function of physical dimensions of the discontinuity and the frequency for a specific substrate. The capacitive element values are determined from the scattering parameters which are obtained using the finite-difference time-domain(FDTD) method. For an open-end, an open-end with connected ground planes and a gap, the numerical results of the FDTD are compared with the quasi-static results which are calculated using the three- dimensional finite difference method(3D-FDM).