• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2000.11a
• /
• pp.193-198
• /
• 2000

Switched reluctance motor drives have been finding their applications in the variable speed drives due to their relatively low cost, simple and robust structure, controllability and high efficiency. Fuzzy control does not need any model of plant. It is based on plant operator experience and heuristics. Fuzzy control is basically adaptive and gives robust performance for plant parameter variation. This paper deals with the sped control of switched reluctance motor using fuzzy controller with 7-rule based fuzzy logic. The proposed fuzzy controller is superior to the control performance of the conventional PI controller. The fuzzy controller is implemented by 80C196KC, 16 bit one-chip microcontroller.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2301-2303
• /
• 2002

This paper describes the development of temperature controller for seedbed heating system. This system consisted of three parts; sensing part, control part that includes the PID control algorithm, and actuating part. The control part introduced a phase angle control method of TRIAC and firmware technique using one-chip microcontroller(PIC16C73). For evaluating the performance of a PID control system, the experiment results by a developed controller are compared with these obtained from a conventional controller which utilize ON-OFF control method. The experiment results show that the proposed controller has good control performance.

• Journal of Biosystems Engineering
• /
• v.21 no.4
• /
• pp.422-428
• /
• 1996

This study was conducted to developed to develop a simple battery-powered autonomous vehicle for greenhouse works. A steering method using speed difference of two independent driving motors was adopted. DC motor driving circuit, speed control circuit and controller using one-chip microcomputer were constructed. The inputs of controller are rolling of the vehicle and current speed of driving motors. Using these signals, automatic guidance system along furrow was developed. A computer simulation program by the kenematic analysis was developed to find out optimal control algorithm. The results of this study are as follows. 1. Automatic guidance system along the furrow that adopted two independent driving motors and rolling of vehicle was developed. 2. The results of simulation showed that PID control was adequate to automatic guidance system along furrow. 3. Two commercial 12V battery serially connected were able to drive the vehicle on the soil ground for five hours in continuous operation and for four hours in intermittent operation without recharging the battery. 4. The speed range was 0-0.7m/s and the rolling of vehicle could be controlled within $pm5^{\circ}$ range. 5. From a series of tests, developed vehicle was found to be a useful tool for greenhouse works.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.88-95
• /
• 2004

Micro stepping method is adopted in order to eliminate effectively the resonant phenomena and to increase the positional resolution. Exist micro-step method by using Sinusoidal waveform, drive circuit is complex by using micro controller and ROM, it have fault on cost Increase. This paper proposed trapezoidal current wave form for simple control circuit and micro stepping method by using a low cost controller. This paper proposed method verify by using CPLD(EPM9320RC208-15) of low cost. This paper make experiment that comparison of exist method and proposed method. This paper obstruct a escape of motor by using high speed detect.

• ETRI Journal
• /
• v.30 no.3
• /
• pp.403-411
• /
• 2008

This paper introduces an interconnect delay fault test (IDFT) controller on boards and system-on-chips (SoCs) with IEEE 1149.1 and IEEE 1500 wrappers. By capturing the transition signals launched during one system clock, interconnect delay faults operated by different system clocks can be simultaneously tested with our technique. The proposed IDFT technique does not require any modification on boundary scan cells. Instead, a small number of logic gates needs to be plugged around the test access port controller. The IDFT controller is compatible with the IEEE 1149.1 and IEEE 1500 standards. The superiority of our approach is verified by implementation of the controller with benchmark SoCs with IEEE 1500 wrapped cores.

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.250-253
• /
• 1989

As the necessity of increasing the midnight base load is extensively increased, electric power companies have to increase the demand of midnight electrical power by lowering the electrical charge rate at midnight. One of the most widely used midnight equipments is the heat Storage type's electrical boiler. A Single chip microprocessor controller for the heat-storage type's electrical boiler is developed. This controller call reduce the undesirable peak load at the begining of midnight (i.e.11 P.M.) time band by using backward load control method. Futhermore, this controller enables reservation of heat storge and the effective heating control the field test has been done by use the boiler for 66$m^2$ with the heater of 21KW quality.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.7
• /
• pp.649-655
• /
• 2007

In this paper, a time-delayed controller for position control of humanoid robot arms is designed and implemented on a field programmable gate array(FPGA) chip. The time-delayed control algorithm is simple to implement, and robust to reject disturbances. The time-delayed control method uses the one sample time-delayed previous information to cancel out uncertainties in the system. Since the sampling time is so fast with the current hardware technology, the time-delayed controller can be implemented. However, inertia values should be correctly estimated to have the better performance. The position tracking tasks of humanoid robot arms are tested to compare performances of several control algorithms including the time-delayed controller.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.869-872
• /
• 2005

In this paper we present a switch wrapper for an AMBA AXI, which is an efficient on-chip-network interface compared to bus-based interfaces in a multiprocessor SoC. The AXI uses an idea of NoC to provide the increasing demands on communication bandwidth within a single chip. A switch wrapper for AXI is located between a interconnection network and two IPs connecting them together. It carries out a mode of routing to interconnection network and executes protocol conversions to provide compatibility in IP reuse. A switch wrapper consists of a direct router, AHB-AXI converters, interface modules and a controller modules. We propose the design of a all-in-one type switch wrapper.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.219-222
• /
• 1991

It is difficult to adapt modern control theory to power conversion system for the price of real time control H/W and the difficulty of S/W implementation. But recent development of large integrated circuit make it possible that One-Chip microprocessor processes high speed arithmatic calculation used in control theory. Specially this chip is called Digital Signal Processing chip. So, this research developes high performance, high reliable digital control system using TMS320C30 of Texas Instrument for real time control in power conversion system.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.1
• /
• pp.70-76
• /
• 2000

This paper describes a one-chip micom controller and phase angle control method for self-starting and energy saving of single-phase induction motor. The proposed method is based on the optimal efficiency control which is running by variable phase angle of main winding current such as to maintain the maximum efficiency characteristics of the motor, in voltage control with TRIAC. Experiments are focused on a capacitor starting single-phase induction motor. The optimal energy saving by variable phase angle control are verified by experimental results. Also, auxiliary winding was controlled by electronic starting switch.