• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.143-149
• /
• 2016

The two-stage converter is widely used in traditional DC/AC inverter. It has several disadvantages such as complex topology, large volume and high loss. In order to overcome these shortcomings, a novel half load-cycle worked dual SEPIC single-stage inverter, which is based on the analysis of the relationship between input and output voltages of SEPIC converters operating in the discontinuous conduction mode (DCM), is presented in this paper. The traditional single-stage inverter has remarkable advantages in small and medium power applications, but it can’t realize boost DC/AC output directly. Besides one pre-boost DC/DC converter is needed between the DC source and the traditional single-stage inverter. A novel DC/AC inverter without pre-boost DC/DC converter, which is comprised of two SEPIC converters, is studied. The output of dual SEPIC converters is connected with anti-parallel and half load-cycle control is used to realize boost and buck DC/AC output directly and work properly, whatever the DC input voltage is higher or lower than the AC output voltage. The working principle, parameter selection and the control strategy of the inverters are analyzed in this paper. Simulation and experiment results verify the feasibility of the new inverter.

• Journal of Power Electronics
• /
• v.11 no.2
• /
• pp.156-162
• /
• 2011

The control loop time delay caused by sampling, the zero-order-holder effect and calculations is inevitable in the digital control of dc-dc switching converters. The time delay will limit the bandwidth of the control loop and therefore degrade the transient performance of digital systems. In this paper, the quantization time delay effects with different time delay values based on a generic second-order system are analyzed. The conclusion that the bandwidth of digital control is reduced by about 20% with a one cycle delay and by 50% with two cycles of delay in comparison with no time delay is obtained. To compensate the time delay and to increase the control loop bandwidth, a duty ratio predictive control scheme based on linear extrapolation is proposed. The compensation effect and a comparison of the load variation transient response characteristics with analogy control, conventional digital control and duty ratio predictive control with different time delay values are performed on a point-of-load Buck converter by simulations and experiments. It is shown that, using the proposed technique, the control loop bandwidth can be increased by 50% for a one cycle delay and 48.2% for two cycles of delay when compared to conventional digital control. Simulations and experimental results prove the validity of the conclusion of the quantization effects of the time delay and the proposed control scheme.

• Parasites, Hosts and Diseases
• /
• v.57 no.2
• /
• pp.185-189
• /
• 2019

To identify the component(s) involved in cell cycle control in the protozoan Giardia lamblia, cells arrested at the G1/S- or G2-phase by treatment with nocodazole and aphidicolin were prepared from the synchronized cell cultures. RNA-sequencing analysis of the 2 stages of Giardia cell cycle identified several cell cycle genes that were up-regulated at the G2-phase. Transcriptome analysis of cells in 2 distinct cell cycle stages of G. lamblia confirmed previously reported components of cell cycle (PcnA, cyclin B, and CDK) and identified additional cell cycle components (NEKs, Mad2, spindle pole protein, and CDC14A). This result indicates that the cell cycle machinery operates in this protozoan, one of the earliest diverging eukaryotic lineages.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.300-300
• /
• 2000

Reduced life-cycle and scale of electronic products make the conventional automated manufacturing system difficult to keep on competitiveness in these days. Reduced life-cycle requires an agile adaptation of manufacturing to new products and reduced scale requires enhanced precision as well as high speed. In this research, We propose a new concept called as "One-Cell Minifactory" in which various processes are combined to produce final modules or products and human interaction can be combined easily. We hope the proposed concept can guide new developments of automated manufacturing in electronics, optics and bio-engineering.

• Journal of Computing Science and Engineering
• /
• v.7 no.2
• /
• pp.81-88
• /
• 2013

In cognitive radio or dynamic spectrum access networks, a rendezvous represents meeting two or more users on a common channel, and negotiating to establish data communication. The rendezvous problem is one of the most challenging tasks in cognitive radio ad hoc networks. Generally, this problem is simplified by using two well-known mechanisms: the first uses a predefined common control channel, while the second employs a channel hopping procedure. Yet, these two mechanisms form a life cycle, when they simplify the rendezvous problem in cognitive radio networks. The main purpose of this paper is to point out how and why this cycle forms.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.5
• /
• pp.1117-1125
• /
• 2000

A current mode PWM method applied one cycle response to averaging circuit model Buck converters is presented. The controller nonlinear PWM implement is based on the error between the switched variable and the response reference to zero each cycle. As the result, the system transfer function is derived as a function of the desired close loop poles, simplifying the design procedure and bringing forward all the important characteristics of the close loop system. The proposed controller has significant advantages over conventional current mode control methods in noise susceptibility, dynamic response and without inductor current sensing, Finally, the simulation and experiment results confirm the proposed PWM control techniques.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.1060-1066
• /
• 1992

One of the undesirable nonlinear phenomenon called 'wind up' occours when the integrator in the controller and the saturated actuator interact. Large overshoot, slow response, instability, limit cycle and jump resonance are the characteristics of wind up phenomenon. Several 'anti-windup' compensators have been developed to prevent some of the aforementioned nonlinear characteristics such as instabilituy and limit cycle, but none has studied the effect of antiwindup compensator on the jump resonance. In this paper, we developed an analyitcal method to design the compensator to prevent not only limit cycle but also jump resonance. An illustrative example is included to show the compensator eliminates jump resonance of effectively.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.250-254
• /
• 1989

This study is to develop the interactive program for work-cell layout of SCAPA type robot using PC. To make the program interactively, we made use of the software which have the function of menu, dialog box, and graphic. By using the mouse, we can progress the program quickly and easily. It has 2 1/2 dimension and provides that one can layout the elements(robot, peripheral device, and etc.), create the work path, and calculate the robot cycle time. By comparing with cycle times of any number of work-cell layout for the same work, we can evaluate work-cell layout and select one work-cell layout to be considered optimal one which has the least cycle time.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.1
• /
• pp.114-122
• /
• 1994

A cold temperature control system for the BAF(batch annealing furnace) has been established in order to reduce energy consumption to imrpove productivity and stabilize the properties of products. Therefore we confirmed a relation between annealing cycle time and atmospheric gas, changing annealing cycle time according to BAF temperature with time during heating and actual temperature measurements cold spot during soaking. The results of the temperature variation effect on the batch annealing are as follows. 1) Cooling rate is increasing gradually with increasing atmospheric gas flow, but heating rate is hardly increasing without atmospheric gas component. Heating time is reduced to one half with increasing atmospheric gas flow rate and changing of atmospheric gas component from HNx to Ax gas and annealing cycle time is reduce to 2.7 times. 2) With enlarging the difference between furnace temperature and soaking temperature at the HNx BAF, heating time becomes short, but cooling time is indifferent. 3) If temperature difference of 300.deg. C in the temperature change of cold spot according to the annealing cycle control temperature, Hi-CON/H2BAF is interchanging at each other at 26hours, but HNxBAF at 50 hours. 4) Soaking time at batch annealing cycle determination is made a decision by the input coil width, and soaking time for quality homogenization of 1219 mm width coil must be 2.5 hours longer then that of 914mm width coil for the same coil weight at Hi-CON/H2BAF. But, it is necessary to make 2 hours longer at HNxBAF.

• Journal of Sensor Science and Technology
• /
• v.25 no.1
• /
• pp.65-70
• /
• 2016

We devised a method to control the temperature of a liquid bath as low as $-100^{\circ}C$ using the duty cycle control of a solenoid valve. The solenoid valve controls the flow of liquid nitrogen that we used as a cryogen in this system. By controlling the duty cycle of a solenoid valve using feedback from the measured temperature of the liquid bath, we were able to achieve temperature stability within ${\pm}19mK$ around $-100^{\circ}C$. We also demonstrated that by taking average values of the temperature readings for sequence of measurements from more than one thermometer, it is possible to use this system for the calibration of thermometers within 3 mK. This system and the control method can be used for the precise temperature control in the range between $0^{\circ}C$ and $-100^{\circ}C$, where commercially available precision baths are much expensive and hard to be built in customized configurations.