• International Journal of Computer Science & Network Security
• /
• v.22 no.10
• /
• pp.214-222
• /
• 2022

In these proceedings, we will address the problem of air pollution on the premises of the Cement factory SHARRCEM L.L.C. in Hani Elezit in the Republic of Kosovo respectively around the clinker cooler, rotary kiln, and raw material mill. By air pollution, we mean the introduction of chemicals, particles, or other harmful materials into the atmosphere which in one way or another causing damage to the development of plants and organisms. Air pollution occurs when certain substances are released into the air, which depending on the quantitative level, can be harmful to human health, animals, and the environment in general. The analysis of air shows the influence of the extractive and processing industry on the chemical composition of air. Parameters analyzed though under control such as the case of carbon dioxide, due to the increasing production capacity of cement, the production of hundreds of thousands of cubic meters of CO₂ gas made CO₂ production a concern. With the purchase of the latest technology by the SHARCEM Factory in Hani Elezit, the amount of air pollution has been reduced and the allowed parameters of environmental pollution have been kept under control. Air pollutants are introduced into the atmosphere from various sources which change the composition of the atmosphere and affect the biotic environment.The concentration of air pollutants depends not only on the quantities that are emitted from the sources of air pollution but also on the ability of the atmosphere to absorb or disperse these emissions. Sources of air pollutants include vehicles, industry, indoor sources, and natural resources. There are some natural pollutants, such as natural fog, particles from volcanic eruptions, pollen grains, bacteria, and so on.

• Computers and Concrete
• /
• v.20 no.2
• /
• pp.165-176
• /
• 2017

Textile Reinforced Cementitious Composite (TRCC) became the most common construction material lately and have excellent properties. TRCC can be employed in the manufacture of thin-walled facade elements, load-bearing integrated formwork, tunnel linings or in the strengthening of existing structures. These composite materials are a combination of matrix and textile materials. There isn't much research done about the usage of polymer modified matrices in textile reinforced cementitious composites. In this study, matrix materials named as fine grained concretes ($d_{max}{\leq}1.0mm$) were investigated. Air entraining effect of polymer modifiers were analyzed and air void content of fine grained concretes were identified with different methods. Aim of this research is to study the effect of polymer modification on the air content of fine grained concretes and the role of defoamer in controlling it. Polymer modifiers caused excessive air entrainment in all mixtures and defoamer material successfully lowered down the air content in all mixtures. Latex polymer modified mixtures had higher air content than redispersible powder modified ones. Air void analysis test was performed on selected mixtures. Air void parameters were compared with the values taken from air content meter. Close results were obtained with tests and air void analysis test found to be useful and applicable to fine grained concretes. Air void content in polymer modified matrix material used in TRCC found significant because of affecting mechanical and permeability parameters directly.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.27-33
• /
• 1985

Air-drying tests were carried out on green taun (Pometia pinnata f glabra) for 25-mm and 50-mm thickness to elucidate drying characteristics on air-drying rate, time and defects in spring and air-drying calendar. The results of this study were as follows: 1. The air-dried lumber for 25-mm thickness from an initial average moisture content (MC) of $58.3{\pm}3.5$ percent reached 30 percent MC in 17 days, 25 percent MC in 24 days, 20 percent MC in 38 days and 15 percent MC in 84 days. 2. The air-dried lumber for 50-mm thickness from an initial average MC of $59.6{\pm}5.0$ percent reached 30 percent MC in 39 days, 25 percent MC in 55 days and 20 percent MC in 84 days. 3. Air-drying calendar that could be useful in estimating drying times for each month developed by the use of climatological data for Suwon. Total number of effective air-drying days during a year were 243.5 days and the major determinant of the effect air-drying days was temperature. 4. The air-drying rates for 25-mm and 50-mm coated lumber were slight1y slower than those of uncoated lumber. The number and total length of both end checks and surface checks for end coated lumber were less severe than those of uncoated lumber.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.252-257
• /
• 2007

The present study investigated the effect of air velocity on frost formation of slit fin-and-tube heat exchanger under frosting condition. The slit fin-and-tube heat exchanger with outer tube diameter 7.0mm and 1 row was used. Air side pressure drop, photographs of frost distribution, frost accumulation and frost thickness were presented with respect to the frosting time. In the early stage of experiment, the case with air velocity of 1.5m/s showed 403% higher for the air pressure drop than the case with the air velocity of 0.5m/s. As the frost was accumulated, the effect of air velocity on air pressure drop was decreased. In the end stage of test, air pressure drops of two cases were very close and air pressure drop for the air velocity of 0.5m/s was higher than that of 2.0m/s. It was also shown in the photographs of frost distribution, frost accumulation and frost thickness. From frost thickness, fanning friction factor was presented.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.2
• /
• pp.142-148
• /
• 2007

The purpose of this study is to suggest the effective ventilation strategies and control methods that can minimize energy cost maintaining acceptable IAQ level in apartment house. The effects of the air-cleaning and heat-recovery ventilation system on IAQ under various operating conditions are investigated based on the experimental and CFD analyzed results. The results can be summarized as follows. (1) When a ventilator is not operated, the concentration of several pollutants may highly show in the house even though environment-friendly building materials are applied. Therefore, a mechanical ventilation system is required to obtain proper ventilation. (2) The pollutant concentration is noticeably deceased under air-cleaning/ventilation mode of air-clinic system, however, pollutant of kitchen is stagnant, because fresh air is not carried into the kitchen. (3) When air-clinic system is only equipped at master bedroom and living room, the system does not effectively deliver fresh air throughout the whole house, and then high pollutant concentration is obtained in each room. In contrast the average pollutant concentration meets the guideline when air-clinic system is installed at each room. (4) The air-cleaning/ventilation mode significantly affects on room ventilation in comparison with ventilation mode only.

• Journal of Power System Engineering
• /
• v.6 no.4
• /
• pp.30-35
• /
• 2002

This study represents the effects of the material of the air cleaner on the performance in a 4-stroke spark-ignition engine for motorcycles. This study is mainly focused on the possibility of the adopting the STS wire mesh air cleaner of a S.I engine. For investigating the possibility of that, the engine power, the fuel consumption and the exhaust gas analysis were carried out for the synthetic fiber air cleaner and the different size of 200 mesh, 250 mesh, 300 mesh of STS wire mash air cleaner. As the results of this study, the performance of STS wire air cleaner was similar to the fiber air cleaner at 9000 rpm but 300 mesh of STS air cleaner had a high engine power and torque at 9500 rpm. In the case of the synthetic fiber air cleaner the concentration of CO was low at 6500 rpm and in the case of the 300 mesh in STS wire mesh air cleaner the concentration of HC was lowest at all experimental regions.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.4
• /
• pp.371-383
• /
• 1999

This paper discusses the importance of indoor air quality based on literaure review of domestic and foreign studies. A number of international efforts to propose standards and guidelines for indoor environmental quality are also reviewed. The pattern of major studies on indoor air quality focussed on characterizaton of gaseous pollutants, particulates, and other specific pollutants during the past decades, whereas VOCs, specific carcinogen, and microbiological agents might be good target pollutants to investigate the effects of human health in recent years. Management of indoor air quality requires a different approach than that adopted for outdoor air. Adequate ventilation of the indoor environment is essential, and a balance between energy conservation and the need for good air quality is required. The ways for managing indoor air quality that will be of great importance are discussed a role of control policy for guidance on how to achieve good indoor air quality.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.1
• /
• pp.20-29
• /
• 1995

A theoretical model for film condensation of a vapor including a relatively lighter noncondensable gas on a horizontal tube has been formulated on the basis of the conservation laws and other fundamental physical principles. The model is applied to the prediction of the condensation heat transfer characteristics for the Freon vapor in the presence of air on a horizontal tube. Calculated results for the mean heat transfer coefficient, which is shown to depend strongly on the bulk concentration of air, are in good agreement with the available experimental results for a range of operating conditions. The distributions of physical quantities along the surface of tube are also calculated, such as the boundary layer thickness and local heat transfer coefficient. The present model is readily reduced to the Nusselt model as the bulk concentration of air decreases to zero. Therefore, the transition from the condensation of pure vapor to that of vapor-air mixture occurs continuously not abruptly.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.12 no.2
• /
• pp.61-69
• /
• 2004

In this study, on-site performance test of an air source heat pump which has a rated capacity of 10 RT is carried out. Since indoor and outdoor air conditions can not be controlled to satisfy the standard test conditions, experiments are done with the inlet air conditions as they exist. To estimate the performance of the heat pump for other conditions, the heat pump is modeled with a small number of characteristic parameters. The values of the parameters are determined from the few measurements measured on-site during steady operation. A simulation program is developed to calculate cooling capacity and power consumption at any other arbitrary operating conditions. The simulation results are in good agreement with the experiment. This study provides a method of an on-site performance diagnosis of an air source heat pump.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.40
• /
• pp.97-144
• /
• 2008

The purpose of this paper is to review the text of national legislation relating to the carrier's liability in respect of the carriage of passengers, baggage and cargo by air in major states such as United Kingdom, Germany, France, Canada, Russia and China, and to compare the air carrier's liability under the national legislations of above states with them under the Warsaw System relating to the international carriage by air. Also this paper reviews the text of the draft legislation relating to the carrier's liability in respect of the carriage by air in Korea. The Warsaw Convention for the Unification of Certain Rules Relating to International Carriage was adopted in 1929. In 1999, the ICAO adopted the Montreal Convention for the Unification of Certain Rules for International Carriage by Air vastly modernizing the unification of private air law. The Montreal Convention replaced the instruments of the “Warsaw System”, and came into force on 4 November 2003. The Montreal Convention is not only an international convention. It has also exercised a considerable influence on national legislation. A the Convention, or certain of its principles, with the object of regulating their national air transport. The main feature of the liability regime of the air carrier under the Montreal Convention is the two-tier liability system for death or injury of the passenger with strict liability up to 100,000 SDR and presumptive liability with a reversed burden of proof without any limit above that threshold. The principles of the liability of the air carrier under the Montreal Convention have been adopted into national legislations by the United Kingdom, Germany, France, Canada, Russia and China. Now the Ministry of Justice of Korea is proceeding to make a new national legislation relating to the liability of the air carrier in respect of the carriage by air. The draft legislation of the Part VI the Carriage by Air of the Commercial Code of Korea has adopted the main principles of the liability of the air carrier under the Montreal Convention. In conclusion, the national legislation relating to the liability of the air carrier in Korea will contribute to settle efficiently the dispute on the carrier's liability in respect of the carriage of passengers, baggage and cargo by air.