• Korean Journal of Soil Science and Fertilizer
• /
• v.22 no.3
• /
• pp.180-190
• /
• 1989

In order to obtain basic information on soil inprovement and management of two reclaimed paddy soils, Munpo and Pori series, this study was carried out by investigating the change of physico-chemical and soil mechanical properties. 1. In the Munpo series, the contents of salt in the soil and ground water before paddy rice transplanting at 6 years after reclamation were 0.60 and 1.84%, respectively, and the safty cultivation of paddy rice was possible after 20 years, while that of the Pori series was after 12 years. 2. In the Munpo series, the change of the soil particle size according to the ages after reclamation showed negative correlation with sandy contents, but clay contents had positive correlation both in the surface and subsurface soils. The pori series showed reverse tendency. 3. Between the N-value and Atterberg limits and the ages showed negative correlation in both Munpo and Pori series, but clay-activity showed positive. Arid the cole values showed positive correlation in the Munpo series, but negative in the Pori series. 4. Cone penetrating resistance in the surface of the Munpo series after 6 years of reclamation was 62.9, after 20 years 24.5 and $16.7kg/cm^2$ in 15cm of soil depth at depth of 22.5cm after 27 years. In the Pori series, it was $3kg/cm^2$ at 15-20cm of soil depth after 12 years and it used after being creation of hard pan layer after 23 years. 5. Change of the clay minerals by the different year after accomplishment of tidal reclamation did not show. The major clay minerals were illite and kaolinite, and accessory clay minerals were montmorillonite and vermiculite in both Munpo and Pori series.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.599-612
• /
• 2017

Human hair (HH) is produced as a waste from beauty parlor and barbershop. HH-based adhesives were formulated with NaOH-hydrolyzed HH, $H_2SO_4$-hydrolyzed chicken blood (CB) and PF as a crosslinking agent. Physicochemical properties and retention rate against hot water of the adhesives were measured to investigate the potential of HH as a raw material of wood adhesives. HH was composed of keratin-type protein of 80% and over. Ash of less than 0.1% was contained in HH. Among the amino acids included in HH, glutamic acid showed the highest content, followed by cysteine, serine, arginine and threonine. Solid content of the adhesives ranged from 33.2% to 41.8% depending on hydrolysis conditions of HH and PF type. Viscosity at $25^{\circ}C$ ranged from 300 to $600mPa{\cdot}s$ resulting in a sprayable adhesive. Retention rate against hot water measured to evaluate the water resistance of adhesives was the highest in the cured resin formulated with 5% NaOH-hydrolyzed HH and 5% $H_2SO_4$-hydrolyzed CB. Meanwhile, the molar ratio of formaldehyde to phenol in PF did not have a significant impact on the retention rate of HH-based adhesives. When the retention rates of HH-based adhesives were compared to those of conventional wood adhesive resins used for the production of wood-based panels extensively, HH-based adhesives formulated with 30 wt% PF showed lower retention rate than commercial urea-formaldehyde resin. However, when PF content was increased to 35 wt%, the retention rate greatly increased and approached to that of commercial melamine-urea-formaldehyde resin. Except for the results mentioned above, the analysis of economic feasibility suggests that HH-based adhesives can be used for the production of wood-based panels if HH is hydrolyzed in proper conditions and then the HH-based adhesives are formulated by the HH hydrolyzates with 35 wt% PF.

• Microbiology and Biotechnology Letters
• /
• v.39 no.4
• /
• pp.382-386
• /
• 2011

Microbial fuel cells (MFC), devices that use bacteria as a catalyst to generate electricity, can utilize a variety of organic wastes as electron donors. The current generated may differ depending on the organic matter concentrations used, when other conditions, such as oxidant supply, proton transfer, internal resistance and so on, are not limiting factors. In these studies, a single-cathode type MFC (SCMFC) and dual-cathode type MFC (DCMFC) were used to ascertain the current's improvement through an increase in the contact area between the anode and the cathode compartments, because the cathode reaction is one of the most serious limiting factors in an MFC. Also an MFC was conducted to explore whether an improvement in electricity generation resulted from oxidizing the carbon sources and nitrates. About 250 mg $L^{-1}$ sodium acetate was fed to an anode compartment with a flow rate of 0.326 mL $min^{-1}$ by continuous mode. The current generated from the DCMFC was higher than the value produced from MFC with a single cathode. COD removal of dual-cathode MFC was also higher than that of single-cathode MFC. The nitrate didn't affect current generation at 2 mM, but when 4 and 8 mM nitrate was supplied, the current in the single-cathode and dual-cathode MFC was decreased by 98% from $5.97{\pm}0.13$ to $0.23{\pm}0.03$ mA and $8.40{\pm}0.23$ to $0.20{\pm}0.01$ mA, respectively. These results demonstrate that increasing of contact area of the anode and cathode can raise current generation by an improvement in the cathode reaction.

• Clinical and Experimental Pediatrics
• /
• v.46 no.8
• /
• pp.777-783
• /
• 2003

Purpose : The aim of this study was to evaluate the effect of inhaled nitric oxide(iNO) on gas exchange, hemodynamics and pulmonary inflammation in newborn piglets with E. coli induced septic lung. Methods : Twenty three instrumented and ventilated piglets were randomized into three groups : CON(n=6), PCON(n=9), and PNO(n=8). In the piglets of the PCON and PNO groups, E. coli septic lung was induced by endotracheal instillation of E. coli. Ten ppm iNO was given continuously in the PNO group after endotracheal instillation of E. coli. All animals were mechanically ventilated for six hour with a peak inspiratory pressure of 30 $cmH_2O$, frequency of 25 breaths/min, $FiO_2$ 1.0 and a positive end-expiratory pressure of 4 $cmH_2O$. All measurements were made at one hour intervals during the experiment. At the end of the experiment, lung tissue was harvested for the analysis of myeloperoxidase activity, indicative of lung inflammation. Results : All piglets with pulmonary instillation of E. coli developed E. coli sepsis. Piglets in the PCON group developed progresseve pulmonry hypertension, hypoxemia and hypercarbia compared to the CON group due to increased pulmonary vascular resistance, intrapulmonary shunt fraction and physiologic dead space fraction. iNO did not reverse pulmonary hypertension in the PNO group. However iNO significantly improved oxygenation, which was attributed to marked improvement of venous admixture and partial attenuation of increase in dead space fraction. Increased myeloperoxidase activity in PCON compared to CON was significantly attenuated in PNO. Conclusion : iNO improves oxygenation and lung inflammation in newborn piglets with E. coli induced septic lung.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.4
• /
• pp.223-231
• /
• 2012

The purpose of this study is to investigate basically the mechanism of heat transfer by the resolution of complex fluid flow inside a sophisticated designed screw dryer for the treatment of sewage sludge by using numerical analysis and experimental study. By doing this, the result was quite helpful to obtain the design criteria for enhancing drying efficiency, thereby achieving the optimal design of a multiple screw type dryer for treating inorganic and organic sludge wastes. One notable design feature of the dryer was to bypass a certain of fraction of the hot combustion gases into the bottom of the screw cylinder, by the fluid flow induction, across the delicately designed holes on the screw surface to agitate internally the sticky sludges. This offers many benefits not only in the enhancement of thermal efficiency even for the high viscosity material but also greater flexibility in the application of system design and operation. However, one careful precaution was made in operation in that when distributing the hot flue gas over the lump of sludge for internal agitation not to make any pore blocking and to avoid too much pressure drop caused by inertial resistance across the lump of sludge. The optimal retention time for rotating the screw at 1 rpm in order to treat 200 kg/hr of sewage sludge was determined empirically about 100 minutes. The corresponding optimal heat source was found to be 150,000 kcal/hr. A series of numerical calculation is performed to resolve flow characteristics in order to assist in the system design as function of important system and operational variables. The numerical calculation is successfully evaluated against experimental temperature profile and flow field characteristics. In general, the calculation results are physically reasonable and consistent in parametric study. In further studies, more quantitative data analyses such as pressure drop across the type and loading of drying sludge will be made for the system evaluation in experiment and calculation.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.4
• /
• pp.249-255
• /
• 2009

The performance of microbial fuel cell (MFC) can be affected by many factors including the rate of organic matter oxidation, the electron transfer to electrode by electrochemical bacteria, proton diffusion, the concentration of electron acceptor, the rate of electron acceptor reduction and internal resistance. the performance of MFC using oxygen as electron acceptor can be influenced by oxygen concentration as limit factors in cathode compartment. Many studies have been performed to enhance electricity production from MFC. The series or parallel stacked MFC connected several MFC units can use to increase voltages and currents produced from MFCs. In this study, a single MFC (S-MFC) and a stacked MFC (ST-MFC) using acetate as electron donor and oxygen as electron acceptor were used to investigate the influence of dissolved oxygen (DO) concentrations in cathode compartment on MFC performance. The power density (W/$m^3$) of S-MFC was in order DO 5 > 3 > 7 > 9 mg/L, the maximum power density (W/$m^3$) of S-MFC was 42 W/$m^3$ at DO 5 mg/L. The power density (W/$m^3$) of ST-MFC was in order DO 5 > 7 > 9 > 3 mg/L and the maximum power density (W/$m^3$) of STMFC was 20 W/$m^3$ at DO 5 mg/L. These results suggest that the DO concentration of cathode chamber should be considered as important limit factor of MFC operation and design for stacked MFC as well as single MFC. The results of ST-MFC operation showed the voltage decrease of some MFC units by salt formation on the surface of anode, resulting in decrease total voltage of ST-MFC. Therefore, connecting MFC units in parallel might be more appropriate way than series connections to enhance power production of stacked MFC.

• Journal of Applied Biological Chemistry
• /
• v.52 no.2
• /
• pp.51-57
• /
• 2009

To investigate expression patterns of chitinase, ${\beta}$-1,3-glucanase and peroxidase involved in biological control of phytopathogens, three oil seed rapes (Capitol, Pollen and Saturnin) were used. Activities of the enzymes in old leaves were $9.7{\sim}11.8$ unit/mg protein in chitinase, $11.1{\sim}17.3$ unit/mg protein in ${\beta}$-1,3-glucanase and $0.6{\sim}1.7$ unit/mg protein in peroxidase. Activities of the enzymes in roots were $39.2{\sim}49.0$ unit/mg protein in chitinase, $49.9{\sim}62.0$ unit/mg protein in ${\beta}$-1,3-glucanase and $2.4{\sim}3.8$ unit/mg protein in peroxidase. Chitinase and ${\beta}$-1,3-glucanase activity were the highest level in Saturnin leaves and in Capitol roots while activities of those were the lowest level in Capitol leaves. Also, chitinase and ${\beta}$-1,3-glucanase and peroxidase activity were the lowest level in Saturnin roots. Active bands of chitinase isoform in leaves (73, 51, 40, 34, and 29 kDa) and in roots (100, 57 34, and 29 kDa) tissues showed in the SDS-PAGE gel. Active bands of ${\beta}$-1,3-glucanase isoform in leaves and roots (75 and 55 kDa) tissues showed on the SDS-PAGE gel. Active staining of peroxidase showed the strongest level in leaves and roots of Pollen. Active bands of peroxidase isoform in leaves (122, 114, and 93 kDa) and in roots (135, 122, 114, and 93 kDa) tissues showed on the Native-PAGE gel. These results indicated that establishment of expression pattern of enzymes in rape tissues could play as an important role with respect to resistance of plant pathogens in rape.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.4
• /
• pp.699-710
• /
• 2020

The purpose of this study was to investigate the effect of combined exercise on lung function, blood vitamin D, calcium and bone metabolism hormones in elderly women who are over 65 years by dividing them into a combined exercise group(n=13), control group(n=17). The combined exercise program included 60-minutes sessions 3times each week. Aerobic exercise intensity was 40-50%HRR(RPE 12-13) for 1-4 week, 50-60%HRR(RPE 13-14) for 5-8 week, and 60-70%HRR(RPE 14-15) for 9-12 week and resistance exercise intensity was set at OMNI-RES 3-4 for 1-4 week, OMNI-RES 5-6 for 5-8 week, OMNI-RES 7-8 for 9-12 week. As a result, lung function indicated that FEV₁ showed an interaction effect between group and time and FVC/FEV₁ levels significantly increased in combined exercise group. Blood vitamin D showed an interaction effect between group and time, also, significantly increased in combined exercise group and control group. Calcium showed an interaction effect between group and time, and significantly decreased in control group. Bone metabolism hormones indicated that both calcitonin and osteocalcin showed an interaction effect between group and time, osteocalcin significantly decreased in control group. For the following this conclusion, elderly women can be improved their lung function through 12 weeks combined exercise and also mitigate the blood vitamin D but there was no meaningful results of calcium and bone metabolism hormones.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.14-14
• /
• 2011

W (tungsten)-alloys will be the most promising plasma facing armor materials in highly loaded plasma interactive components of the next step fusion reactors due to its high melting point, high sputtering resistance and low deuterium/tritium retention. The bonding technology of tungsten to Cu alloy was one of the key issues. In this paper, W/CuCrZr diffusion bonding has been performed successfully by inserting pure metal interlay. The joint microstructure, interfacial elements migration and phase composition were analyzed by SEM, EDS, XRD, and the joint shear strength and micro-hardness were investigated. The mock-ups were fabricated successfully with diffusion bonding and the cladding technology respectively, and the high heat flux test and thermal fatigue test were carried out under actively cooling condition. When Ni foil was used for the bonding of tungsten to CuCrZr, two reaction layers, Ni4W and Ni(W) layer, appeared between the tungsten and Ni interlayer with the optimized condition. Even though Ni4W is hard and brittle, and the strength of the joint was oppositely increased (217 MPa) due primarily to extremely small thicknesses (2~3 ${\mu}m$). When Ti foil was selected as the interlayer, the Ti foil diffused quickly with Cu and was transformed into liquid phase at $1,000^{\circ}C$. Almost all of the liquid was extruded out of the interface zone under bonding pressure, and an extremely thin residual layer (1~2 ${\mu}m$) of the liquid phase was retained between the tungsten and CuCrZr, which shear strength exceeded 160 MPa. When Ni/Ti/Ni multiple interlayers were used for bonding of tungsten to CuCrZr, a large number of intermetallic compound ($Ni_4W/NiTi_2/NiTi/Ni_3T$) were formed for the interdiffusion among W, Ni and Ti. Therefore, the shear strength of the joint was low and just about 85 MPa. The residual stresses in the clad samples with flat, arc, rectangle and trapezoid interface were estimated by Finite Element Analysis. The simulation results show that the flat clad sample was subjected maximum residual stress at the edge of the interface, which could be cracked at the edge and propagated along the interface. As for the rectangle and trapezoid interface, the residual stresses of the interface were lower than that of the flat interface, and the interface of the arc clad sample have lowest residual stress and all of the residual stress with arc interface were divided into different grooved zones, so the probabilities of cracking and propagation were lower than other interfaces. The residual stresses of the mock-ups under high heat flux of 10 $MW/m^2$ were estimated by Finite Element Analysis. The tungsten of the flat interfaces was subjected to tensile stresses (positive $S_x$), and the CuCrZr was subjected to compressive stresses (negative $S_x$). If the interface have a little microcrack, the tungsten of joint was more liable to propagate than the CuCrZr due to the brittle of the tungsten. However, when the flat interface was substituted by arc interfaces, the periodical residual stresses in the joining region were either released or formed a stress field prohibiting the growth or nucleation of the interfacial cracks. Thermal fatigue tests were performed on the mock-ups of flat and arc interface under the heat flux of 10 $MW/m^2$ with the cooling water velocity of 10 m/s. After thermal cycle experiments, a large number of microcracks appeared at the tungsten substrate due to large radial tensile stress on the flat mock-up. The defects would largely affect the heat transfer capability and the structure reliability of the mock-up. As for the arc mock-up, even though some microcracks were found at the interface of the regions, all microcracks with arc interface were divided into different arc-grooved zones, so the propagation of microcracks is difficult.

• Weed & Turfgrass Science
• /
• v.7 no.3
• /
• pp.181-190
• /
• 2018

This study was conducted to investigate the occurrence of an acetolactate synthase (ALS) inhibiting herbicide resistant weed on paddy at 289 sites by soil sampling in Chungcheongbuk-Do of Republic of Korea from February to April in 2017. The most dominant weed was Monochoria vaginalis and Echinochloa oryzicola on each city and county. ALS inhibiting herbicide resistant ratio and occurrence area were 80.6% and 28,272 ha, respectively, in Chungcheongbuk-Do which was 3 times than in 5 years ago. The herbicide resistant ratio, Okcheon-Gun was the highest at 93.8%, Chungju-Si, Boeun-Gun, Yeongdong-Gun, Jincheon-Gun and Geosan-Gun were over 80%, Cheongju-Si, Eumseong-Gun and Jeungpyeong-Gun were over 70%. The herbicide resistant area, Cheongju-Si had the largest at 6,957 ha, Chungju-Si was 4,277 ha, Jincheon-Gun and Boeun-Gun was 3,536 ha and 3,282 ha, respectively. By weed, ALS inhibiting herbicide resistant ratio and occurrence area, Monochoria vaginalis was 49%, 17,646 ha, Echinochloa oryzicola 44%, 15,617 ha, Schoenoplectiella juncoides 29%, 10,377 ha, respectively. In all cities and counties of Chungcheongbuk-Do, Monochoria vaginalis and Echinochloa oryzicola are more than 40% resistant to ALS inhibiting herbicides, intensive management is required. The use of sulfonylurea herbicides is increasing, most farmers use herbicides 10 days after transplanting, so management after transplanting is necessary and the occurrence of herbicide resistant weeds should be reduced by alternating herbicide application every year.