• 한국전기전자재료학회논문지
• /
• 제30권1호
• /
• pp.17-22
• /
• 2017

Effects of pH value and deposition time on the electrical properties of (NMC) Ni-Mn-Cu-O and (NMCC) Ni-Mn-Cu-Co-O thin films were investigated. The NMC and NMCC films were prepared by spin spray method. The crystal structure and thickness of the annealed films were changed by the pH value and deposition time, respectively. A single phase of cubic spinel structure was confirmed for the annealed films deposited from solutions with pH 7.6. The resistivity of the annealed films was affected by the crystal structure and microstructure. The TCR (temperature coefficient of resistance) was dependent on the $Mn^{3+}/Mn^{4+}$. Typically, the resistivity of $70.5{\Omega}{\cdot}cm$ and TCR of -3.56%/K at room temperature were obtained for NMCC films deposited from solutions with pH 7.6 for 5 min, and annealed at $450^{\circ}C$ for 3 h.

• Wind and Structures
• /
• 제17권6호
• /
• pp.647-670
• /
• 2013

The paper presents a numerical approach to study of fluid flow characteristics and to predict performance of wind turbines. The numerical model is based on Finite-volume method (FVM) discretization of unsteady Reynolds-averaged Navier-Stokes (URANS) equations. The movement of turbine blades is modeled using moving mesh technique. The turbulence is modeled using commonly used turbulence models: Renormalization Group (RNG) k-${\varepsilon}$ turbulence model and the standard k-${\varepsilon}$ and k-${\omega}$ turbulence models. The model is validated with the experimental data over a large range of tip-speed to wind ratio (TSR) and blade pitch angles. In order to demonstrate the use of numerical method as a tool for designing wind turbines, two dimensional (2-D) and three-dimensional (3-D) simulations are carried out to study the flow through a small scale Darrieus type H-rotor Vertical Axis Wind Turbine (VAWT). The flows predictions are used to determine the performance of the turbine. The turbine consists of 3-symmetrical NACA0022 blades. A number of simulations are performed for a range of approaching angles and wind speeds. This numerical study highlights the concerns with the self-starting capabilities of the present VAWT turbine. However results also indicate that self-starting capabilities of the turbine can be increased when the mounted angle of attack of the blades is increased. The 2-D simulations using the presented model can successfully be used at preliminary stage of turbine design to compare performance of the turbine for different design and operating parameters, whereas 3-D studies are preferred for the final design.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.260-260
• /
• 2011

투명 비정질 산화물반도체는 디스플레이의 구동소자인 박막 트랜지스터에 채널층으로 사용된다. 또한 투명하면서 유연성이 있는 소자를 저비용으로 제작할 수 있는 장점을 가진다. 투명 산화물반도체 재료 중 IGZO는 Si 또는 GaAs와 같은 공유결합성 반도체와는 다른 전자 배치로 전도대가 금속이온의 ns 궤도에서 형성되며, 가전도대가 산소 음이온의 2p 궤도에서 형성된다. 특히 큰 반경의 금속 양이온은 인접한 양이온과 궤도 겹침이 크게 발생하게 되며 캐리어의 효과적인 이동 경로를 제공해줌으로써 다른 비정질 반도체와는 다르게 높은 전하이동도(~10 $cm^2$/Vs)를 가진다. 따라서 저온공정에서 우수한 성능의 TFT소자를 제작할 수 있는 장점이 있다. 본 연구에서는 TFT 채널층으로 사용하기 위한 a-IGZO박막의 산소분압에 따른 특성변화를 분석 하였다. a-IGZO박막은 Pulsed Laser Deposition (PLD)를 이용하여 산소분압(20~200 mTorr) 변화에 따라 Glass기판에 증착하였다. 증착된 a-IGZO 박막의 구조적 특성으로는 X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), 광학적 특성은 UV-vis spectroscopy 분석을 통해서 알아보았다. TFT 채널층의 조건으로는 낮은 off-current, 높은 on-off ratio를 위해 고저항 ($10^3\;{\Omega}cm$)의 진성반도체 성질과 source/drain금속과의 낮은 접촉저항(ohmic contact) 등의 전기적 성질이 필요하다. 따라서 이러한 전기적 특성확인을 위해 transmission line method (TLM)을 사용하여 접촉저항과 비저항을 측정하였고, 채널층으로 적합한 분압조건을 확인해볼 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.465-465
• /
• 2011

In recent years, electrochemical supercapacitors have attracted much attention due to their high power density, long life cycles, and high efficiency. Some supercapacitors using CNTs have been reported, but there are several issues to be resolved for further development of CNT based supercapacitors. One issue is time consuming procedures to prepare CNT films, which may provide poor control of CNT uniformity over the large area of the substrates. Another is new electrolytes replacing the conventional liquid electrolytes in supercapacitors. In this work, We have successfully demonstrated that spray deposition method of multiwalled CNT films using gel electroytes could be promising for CNT-based supercapacitors on ITO substrates. Specific capacitances using gel electrolyte reached up to 1.5 F/g and 9 mF/$cm^2$, and internal resistance was 28 ${\Omega}$. Specific capacitances and internal resistance of supercapacitors with gel electrolyte were better than or comparable to those with liquid electrolytes($KNO_3$, $Na_2SO_4$), indicating that gel electrolytes could replace liquid counterparts in CNT-based supercapacitors. Combined with gel electrolyte, spray deposition method could provide low cost and easily scalable process for high performance supercapacitors using CNT films on ITO for applications in display devices.

• 한국세라믹학회지
• /
• 제51권4호
• /
• pp.265-270
• /
• 2014

Among the Ruddlesden-Popper series, $La_4Ni_3O_{10}$ has received widespread attention as a promising cathode material by reason of its favorable properties for realizing high performance of intermediate temperature solid oxide fuel cells (IT-SOFCs). The $La_4Ni_3O_{10}$ cathode is prepared using the facile sol-gel method by employing tri-blockcopolymer (F127) to obtain a single phase in a short sintering time. There are no reactions between the $La_4Ni_3O_{10}$ cathode and the $Ce_{0.9}Gd_{0.1}O_{2-\delta}$ (GDC) electrolyte upon sintering at $1000^{\circ}C$, indicating that the $La_4Ni_3O_{10}$ cathode has good chemical compatibility with the GDC electrolyte. The maximum electrical conductivity of $La_4Ni_3O_{10}$ reaches approximately 240 S $cm^{-1}$ at $100^{\circ}C$ and gradually decreases with increasing temperaturein air atmosphere. The area specific resistance value of $La_4Ni_3O_{10}$ composite with 40 wt% GDC is $0.435{\Omega}cm^2$ at $700^{\circ}C$. These data allow us to propose that the $La_4Ni_3O_{10}$-GDC composite cathode is a good candidate for IT-SOFC applications.

• 한국전기전자재료학회논문지
• /
• 제29권8호
• /
• pp.470-475
• /
• 2016

In this study, $Zn_xMn_{3-x}O_4$ (x=0.95~1.20) specimens were prepared by using a conventional mixed oxide method. All specimens were sintered in air at $1,200^{\circ}C$ for 12 h and cooled at a rate of $2^{\circ}C/min$ to $800^{\circ}C$, subsequently quenching to room temperature. We investigated the structural and electrical properties of $Zn_xMn_{3-x}O_4$ specimens with variation of ZnO amount for the application of NTC thermistors. As results of X-ray diffraction patterns, all specimens showed the formation of a complete solid solution with tetragonal spinel phase. And, the second phase was observed by the solubility limit of Zn ions in $x{\geq}1.10$ composition. The average grain size was increased from $2.72{\mu}m$ to $4.18{\mu}m$ with increasing the compositional ratio of Zn ion from x=0.95 to 1.20, respectively. $Zn_{1.10}Mn_{1.90}O_4$ specimen showed the minimum electrical resistance of $57.5k{\Omega}$ at room temperature and activation energy of 0.392 eV.

• 대한화학회지
• /
• 제37권1호
• /
• pp.62-67
• /
• 1993

Quinoline계 화합물인 미시적 비선형 광학 특성을 설명하기 위해 반경험적인 AMI 방법을 사용하여 초분극률을 계사하였다. Quinoline 고리에서 이차 비선형 특성에 기여하는 전자공여체, 아미노기와 전자수여체, 니트로기의 반응 위치를 변경하여 미시적 비선형 상수에 대한 이론적 영향을 조사해 보았다. 이차와 삼차 비선형 주쇄고분자로서 물리적, 기계적 성질이 우수한 polyquinoline계 고분자를 이용하기 이해 polyquinoline계 반복단위와 유사한 단분자 quinoline들을 설계하여 각각의 미시적 비선형 상수 및 바닥상태의 쌍극자 모멘트 등을 유한 전기장하에서 계산하여 서로 평가 비교해 보았다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.6-7
• /
• 2008

Current sensing in power semiconductors involves sensing of over-current in order to protect the device from harsh conditions. This technique is one of the most important functions in stabilizing power semiconductor device modules. The sense FET is very efficient method with low power consumption, fast sensing speed and accuracy. In this paper we have analyzed the characteristics of proposed sense FET and optimized its electrical characteristics to apply conventional 450V power MOSFET devices by numerical and simulation analysis. The proposed sense FET has the n-drift doping concentration $1.5\times10^{14}cm^{-3}$, size of $600{\mu}m^2$ with 4.5 $\Omega$, and off-state leakage current below 50 ${\mu}A$. We offer the layout of the proposed sense FET to process actually. The offerd design and optimization methods is meaningful, which the methods can be applied to the power devices having various breakdown voltages for protection.

• 지구물리와물리탐사
• /
• 제8권1호
• /
• pp.73-77
• /
• 2005

전도성 지질에서 얻어진 지표 핵자기 공명(SNMR) 자료를 올바르게 역산하고 해석하기 위해서는 기하의 전기전도도 분포에 대한 정확한 추정이 필요하다. 이러한 추정 결과는 SNMR 수직탐사를 수행하기 이전에 전도도 구조가 지하수 탐지를 방해할 것인지에 대해 결정하는데 유용할 것이다 이 논문에서는 SNMR 모델링을 이용하여 지하 전기전도도 구조가 주어졌을 때, 대부분의 SNMR 신호를 발생하는 심도 범위를 결정하는 방법을 서술하였다. 이 논문에서는 반무한 공간에서 SNMR침투 심도를 추정하는 방법을 사용하였으며 전도성 반무한 공간(<10 ohm-m)에서는 침투심도가 50 m 이내라는 것을 보였다. 또한 이러한 반an한 공간 모델에서는 동일위치 방식의 loop 크기를 늘리더라도 침투심도를 뚜렷이 증가시키지 못함도 알 수 있었다. 이러한 결과는 좀 더 복잡한 1 차원 전도도 구조에 대한 반무한 공간 근사를 통해 전도성 지층에서 신호가 얻어질 수 있는 심도 범위를 합리적으로 추정하는데 사용될 수 있을 것이다.

• 대한금속재료학회지
• /
• 제46권10호
• /
• pp.691-699
• /
• 2008

Electrochemical characteristics of Ti-30Ta-xZr alloys coated with HA/TiN by using magnetron sputtering method were studied. The Ti-30Ta containing Zr(3, 7, 10 and 15wt%) were 10 times melted to improve chemical homogeneity by using a vacuum furnace and then homogenized for 24hrs at $1000^{\circ}C$. The specimens were cut and polished for corrosion test and coating, and then coated with HA/TiN, respectively, by using DC and RF-magnetron sputtering method. The analyses of coated surface and coated layer were carried out by using optical microscope(OM), field emission scanning electron microscope(FE-SEM) and X-ray diffractometer(XRD). The electrochemical characteristics were examined using potentiodynamic (-1,500 mV~ + 2,000 mV) and A.C. impedance spectroscopy(100 kHz ~ 10 mHz) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The microstructure of homogenized Ti-30Ta-xZr alloys showed needle-like structure. In case of homogenized Ti-30Ta-xZr alloys, a-peak was increased with increasing Zr content. The thickness of TiN and HA coated layer showed 400 nm and 100 nm, respectively. The corrosion resistance of HA/TiN-coated Ti-30Ta-xZr alloys were higher than that of the non-coated Ti-30TaxZr alloys, whic hindicate better protective effect. The polarization resistance($R_p$) value of HA/TiN coated Ti-30Ta-xZr alloys showed $8.40{\times}10^5{\Omega}cm^2$ which was higher than that of non-coated Ti-30Ta-xZr alloys.