• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.31-39
• /
• 1999

Previous researches and experiments have already verified that the primary noise source of high pressure tandem axial thpe piston pump is fluid-borne noise from the process of oil distribution between the kidney-shaped port and valve plate. So, many researchers have improved pressure gradients and reduced sound levels by applying pre-compression and pre-decompression metering grooves to valve plate. In practice however, the sound level of th high pressure tandem axial type piston pump is still undesirable. This paper testified the effect of pumping phase of the piston on vibration and noise of th high pressure tandem axial type piston pump on the best of theoretical research in $this^(1)$. Therefore considering the pumping phase of the piston when assembling the tandem axial type piston pump, it is possible to reduce 1.5~2[dB]of sound level.

• Applied Science and Convergence Technology
• /
• 제26권1호
• /
• pp.1-5
• /
• 2017

The spurt vacuum pump is widely used to transfer sludge and slurry, and to control flow rate in a variety of processing fields, such as the oil, chemical, and fiber industries. The efficiency of the pump depends on the design parameters of the impeller, such as the number of blades, and the blade angle. In this study, the effect of the configuration of the impeller discharge angle of a spurt vacuum pump, which influences total head, shaft power, and efficiency, was numerically investigated using the commercial code, ANSYS CFX ver. 16.1. In addition, the performance of the pump was evaluated on the basis of the correlations between the total head, pump efficiency, and pressure distribution.

• 유공압시스템학회:학술대회논문집
• /
• 유공압시스템학회 2010년도 춘계학술대회
• /
• pp.33-38
• /
• 2010

As for an oil hydraulic vane pump of vehicle hydraulic systems, the highest of planning technique required by the acquisition of optimum profile data which can be available to predict noises and vibrations. Pressure pulsation may result in considerable vibration and noise of pump component as well as cavitation in hydraulic system. The influences of the discharge pressure and rotating speed of the vane on the dynamic pressure in chamber surrounding a vane have been investigated. It is very important to predict pressure pulsation in vane pump. This paper presents analysis of technique of vane pump for automatic transmission. The predicted result using AMESim model were good agreement with the experimentally obtained results.

• 한국기계가공학회지
• /
• 제20권10호
• /
• pp.56-62
• /
• 2021

In this study, a cavitation occurrence in a piston-pump inlet was investigated by simulating the pressure distribution, according to the inlet shape of a variable-displacement swash-plate piston pump that supplies high-pressure oil to control the hydraulic system of a marine engine. Two types of pump inlets with different shapes were cast into impression models, and the models were reverse-engineered by 3D scanning. Then, the hydraulic-pressure distribution was analyzed through finite-element analysis. The results of the analysis confirmed that cavitation occurs more easily in the inlet with a steeper slope during pump operation because the inlet pressure on the valve plate is lower than that of the other pump with a gentler inlet slope.

• 대한기계학회논문집A
• /
• 제35권5호
• /
• pp.555-559
• /
• 2011

본 연구는 유압 피스톤 펌프 재료로 사용되고 있는 SACM645소재를 사용하여 모재, QT(quenching & tempering) 시험편 및 QT 질화시험편의 피로특성을 조사하였다. 피로특성 조사결과는 다음과 같다. QT 질화시험편은 피로한도가 인장강도의 80%로 나타나 아주 높은 값을 나타내었다. 이것은 시험편 표면에 단단한 질화처리를 실시하여 피로균열의 발생을 지연시켰고, 피로균열이 발생하더라고 소재가 단단하여 균열진전속도가 늦었다고 판단된다. 파면 관찰결과 피로균열진전 영역에서는 모두 스트라이에이션이 관찰되었고, 피로균열진전 이외의 영역에서 QT 시험편은 벽개파괴의 양상을, 모재와 Qt 질화시험편은 딤플 파괴의 양상을 나타내었다.

• 유공압시스템학회논문집
• /
• 제6권1호
• /
• pp.10-16
• /
• 2009

Automatic power transmission systems consisted of a torque converter and several planetary gear sets, clutches and brakes are controlled by a hydraulic shift control circuit and an electronic transmission control unit. The hydraulic circuit serves for the operation of the torque converter and lubrication oil supply of the transmission system as well as for the actuation of clutches for the automatic gear shift. The complicated hydraulic control circuit constructed by many spools, solenoids, orifices and flow passages are integrated into one small valve block and it is powered by one hydraulic pump. In this paper, a test equipment was developed to measure the oil consumption of each component at various wide operating conditions. Test data about 730 sets acquired from five test items are analyzed and discussed on the oil capacity of the circuit.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.267-272
• /
• 1995

The paper describes an approach for measuring flow ripple generated by oil hydraulic axial piston pumps. Flow ripple has periodic waveforms due to the cyclic nature of a pump's operation, and interacts with the connected hydraulic systems such as pipes and components to produce a pressure ripple, also known as fluid-borne noise. It is indispensable to measure a flow ripple because increasing of vibration and noise caused by a flow ripple has become a point to be considered and has need of solving these problems. The measurement of flow ripple with high frequencies from oil hydraulic axial piston pumps is msde by using the remote instantaneous flow rate measurement method. As a result, the reverse flow through the relief groove in valve plate has an important effect upon a flow ripple generated by a pumps.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 추계학술대회 논문집
• /
• pp.160-162
• /
• 2008

This paper presents the practical pressure control of hydraulic oil-pump system using SR drive for industrial application. In order to get a high performance of pressure dynamics in actual application, a data based PID control scheme is proposed in this paper. The look-up table from pre-measured data produces an approximately proper current reference according to motor speed and oil-pressure. And, PID controller can compensate the pressure error. With the combination of two references, the proposed control scheme can get a fast dynamics and stable operation. Furthermore, the suitable current controller considering the nonlinear characteristics of SRM(Switched Reluctance Motor) and practical test method for data measuring are introduced. The proposed control scheme is verified by the experimental test.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.408-414
• /
• 2014

After drilling operations at the offshore plant to production to crude oil to high pressure. After that time the low pressured of pipe inside when the secondary produce so oil recovery is reduced. At that time injection sea water at the pipe inside through water injection pump that the device Increase recovery so to be research and development at many industry. So developing 3-stage water injection pump at the domestic company. A variety of mathematical analysis during the detailed design analysis was not made through the dynamics characteristic. In this paper, a 2D finite element analysis is performed through the dynamics of the present study was the validation of the model.

• 유공압시스템학회논문집
• /
• 제1권3호
• /
• pp.7-13
• /
• 2004

The hydraulic pump for a Electro-hydrostatic Actuator for aircrafts should be able to quickly feed large volume of oil into hydraulic cylinder in order to reduce the response time. On the other hand, it should be also able to precisely dispense small amount of oil by low-speed operation so that the steady state position control error of the EHA can be accurately compensated. This paper is focused on the investigation how the plasma coating surface treatment of cylinder barrel with CrSiN can contribute to the reduction of low-speed friction torque of a bent-axis type piston pump. The results showed that the reduction of the friction torque was not remarkable, but that the anti-wear characteristics of the CrSiN-coated cylinder barrel were much better that those of the original one.