• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.06a
• /
• pp.231-236
• /
• 1997

To improve electrical properties and uniformity of high-low doped n-type GaAs, new ohmic contacts with a low-resistance and the superior uniformity was developed using a concept of hybrid ohmic contact. The hybrid ohmic contact displayed good surface and interface morphology and had minimum contact resistivity of 3${\times}$10-6 $\Omega$$\textrm{cm}^2$ in a wide annealing temperature ranged from 340$^{\circ}C$ to 420$^{\circ}C$, which was much wider than that of conventional ohmic contacts. The microstructural analysis showed that the Pd/Ge ohmic contact at low annealing temperature (∼300$^{\circ}C$) and also annealing temperature (∼400$^{\circ}C$), resulting ij hybrid ohmic contacts.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.103-104
• /
• 1998

GaN is a ppromising materials fot applications in the blue/ultraviolet (UV) light emitting diodes (LEDs)[1] and laser diodes (LDs) [2] High quality ohmic contacts are very critical to these applications since the qualities of ohmic contact system pplay an impportant roles in the high efficient device opperations. For the n-GaN there have been many repports about ohmic contacts and the sppecific contact resistance were as low as from 10-8$\Omega$cm2 However for the ohmic contacts on pp-GaN much fewer study were repported and the sppecific contact resistivity was much lower than of n-GaN. In this ppapper we repport a new Ni/ppt/Au metallization scheme and discuss the mechanism of ohmic formation

• Korean Journal of Materials Research
• /
• v.13 no.7
• /
• pp.465-472
• /
• 2003

Pd/Ge/Ti/Pt and Pd/Ge/Pd/Ti/Au ohmic contacts to n-type InGaAs were investigated for applications to AlGaAs/GaAs HBT emitter ohmic contacts. In the Pd/Ge/Ti/Pt ohmic contact minimum specific contact resistivity of $3.7${\times}$10^{-6}$ $\Omega$$\textrm{cm}^2$ was achieved by rapid thermal annealing at $^400{\circ}C$/10 sec. In the Pd/Ge/Ti/Au ohmic contact, minimum specific contact resistivity of $1.1${\times}$10^{-6}$ $\Omega$$\textrm{cm}^2$ was achieved by annealing at 40$0^{\circ}C$/10 sec but the ohmic performance was degraded with increasing annealing temperature due to the reaction between the ohmic contact materials and the InGaAs substrate. However, non-spiking planar interface and relatively good ohmic contact (high-$10^{-6}$ /$\Omega$$\textrm{cm}^2$) were maintained after annealing at $450^{\circ}C$/10 sec. Therefore, these thermally stable ohmic contact systems are promising candidates for compound semiconductor devices. RF performance of the AlGaAs/GaAs HBT was also examined by employing the Pd/Ge/Ti/Pt and Pd/Ge/Pd/Ti/Au systems as emitter ohmic contacts. Cutoff frequencies were 63.5 ㎓ and 65.0 ㎓, respectively, and maximum oscillation frequencies were 50.5 ㎓ and 51.3 ㎓, respectively, indicating very successful high frequency operations.

• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.567-571
• /
• 2003

We investigate vanadium (V)-based Ohmic contacts on n-GaN ($N_{d}$=$2.0${\times}$10^{18}$ $cm^{-3}$ ) as a function of annealing temperature. It is shown that the V (60 nm) contacts become Ohmic with specific contact resistances of $10^{-3}$ $- 10^{-4}$ Ω$\textrm{cm}^2$ upon annealing at 650 and $850^{\circ}C$. The V(20 nm)/Ti(60 nm)/Au(20 nm)contacts produce very low specific contact resistances of $2.2 ${\times}$ 10^{-5}$ and$ 4.0${\times}$10^{-6}$ Ω$\textrm{cm}^2$ when annealed at 650 and $850{\circ}C$, respectively. A comparison shows that the use of the overlayers (Ti/Au) is very effective in improving Ohmic property. Based on the current-voltage measurement, Auger electron spectroscopy, glancing angle X-ray diffraction, and X-ray photoemission spectroscopy results, the possible mechanisms for the annealing temperature dependence of the Ohmic behavior of the V-based contacts are described and discussed.d.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.23-23
• /
• 2003

GaN-related semiconductors are of great technological importance for the fabrication of optoelectronic devices, such as blue and ultra violet light emitting diodes (LEDs), laser diodes, and photo-detectors. One of the most important applications of GaN-based LEDs is solid-state lighting, which could replace incandescent bulbs and ultimately fluorescent lamps. For solid-state lighting applications, the achievement of high extraction efficiency in LED structures is essential. For flip-chip LEDs (FCLEDS), the formation of low resistance and high reflective p-GaN contact is crucial. So far, a wide variety of different methods have been employed to improve the ohmic properties of p-type contacts to GaN. For example, surface treatments using different chemical solutions have been successfully used to produce high-quality ohmic contacts, Metallization schemes, such as Ta/Ti contacts to p-GaN, were also investigated. For these contacts, the removal of hydrogen atoms from the Mg atoms doped n the GaN was argued to be responsible for low contact resistances.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.290-293
• /
• 2003

Ohmic contact characteristics of Al ion implanted n-type SiC wafer were investigated. Al ions implanted with high dose to obtain the final concentration of $5{\times}10^{19}/cm^3$, then annealed at high temperature. Firstly, B ion ion implanted p-well region were formed which is needed for fabrication of SiC devices such as DIMOSFET and un diode. Secondly, Al implanted high dose region for ohmic contact were formed. After ion implantation, the samples were annealed at high temperature up to $1600^{\circ}C\;and\;1700^{\circ}C$ for 30 min in order to activate the implanted ions electrically. Both the inear TLM and circular TLM method were used for characterization. Ni/Ti metal layer was used for contact metal which is widely used in fabrication of ohmic contacts for n-type SiC. The metal layer was deposited by using RF sputtering and rapid thermal annealed at $950^{\circ}C$ for 90sec. Good ohmic contact characteristics could be obtained regardless of measuring methods. The measured specific contact resistivity for the samples annealed at $1600^{\circ}C\;and\;1700^{\circ}C$ were $1.8{\times}10^{-3}{\Omega}cm^2$, $5.6{\times}10^{-5}{\Omega}cm^2$, respectively. Using the same metal and same process of the ohmic contacts in n-type SiC, it is found possible to make a good ohmic contacts to p-type SiC. It is very helpful for fabricating a integrated SiC devices. In addition, we obtained that the ratio of the electrically activated ions to the implanted Al ions were 10% and 60% for the samples annealed at $1600^{\circ}C\;and\;1700^{\circ}C$, respectively.

• Journal of the Korean Vacuum Society
• /
• v.12 no.4
• /
• pp.218-227
• /
• 2003

Pd/Si/Ti/Pt and Pd/Si/Pd/Ti/Au ohmic contacts to n-type InCaAs were investigated for applications to AlGaAs/GaAs HBT emitter ohmic contacts. In the Pd/Si/Ti/Pt ohmic contact, as-deposited contact showed non-ohmic behavior, and high specific contact resistivity of $5\times10^{-3}\Omega\textrm{cm}^2$ was achieved by rapid thermal annealing at $375^{\circ}C$/10 sec. However, the specific contact resistivity decreased remarkably to $2\times10^{-6}\Omega\textrm{cm}^2$ by annealing at $425^{\circ}C$/10sec. In the Pd/Si/Pd/Ti/Au ohmic contact, minimum specific contact resistivity of $3.9\times10^{-7}\Omega\textrm{cm}^2$ was achieved by annealing at $400^{\circ}C$/20sec. In both ohmic contacts, low contact resistivity and non-spiking planar interface between ohmic materials and InGaAs were maintained. Therefore, these thermally stable ohmic contact systems are promising candidates for compound semiconductor devices. RF performance of the AlGaAs/GaAs HBT was also examined by employing the Pd/Si/Ti/Pt and Pd/Si/Pd/Ti/Au systems as emitter ohmic contacts. Cutoff frequencies were 63.9 ㎓ and 74.4 ㎓, respectively, and maximum oscillation frequencies were 50.1 ㎓ and 52.5 ㎓, respectively. It shows very successful high frequency operations.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.10
• /
• pp.495-499
• /
• 2004

Characteristics of ohmic Ni/Si/Ni contacts to n-type 4H-SiC are investigated systematically. The ohmic contacts were formed by annealing Ni/Si/Ni sputtered sequentially The annealings were performed at 950℃ using RTP in vacuum ambient and N₂ ambient, respectively. The specific contact resistivity(p/sub c/), sheet resistance(R/sub s/), contact resistance (R/sub c/) transfer length(L/sub T/) were calculated from resistance(R/sub T/) versus contact spacing(d) measurements obtained from TLM(transmission line method) structure. While the resulting measurement values of sample annealed at vacuum ambient were p/sub c/ = 3.8×10/sup -5/Ω㎠, R/sub c/ = 4.9 Ω and R/sub T/ = 9.8 Ω, those of sample annealed at N₂ ambient were p/sub c/ = 2.29×10/sup -4/Ω㎠, R/sub c/ = 12.9 Ω and R/sub T/ = 25.8 Ω. The physical properties of contacts were examined using XRD 3nd AES. The results showed that nickel silicide was formed on SiC and Ni was migrated into SiC. This result indicates that Ni/Si/Ni ohmic contact would be useful in high performance electronic devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1992.07a
• /
• pp.25-25
• /
• 1992

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1378-1380
• /
• 2001

Ohmic contacts have been fabricated on p-type 4H-SiC using Pt/Ti. Low resistivitf Ohmic contacts of Pt/Ti to p-type 4H-SiC were investigated. Specific contact resistances were measured using the transmission line model method, and the physical properties of the contacts were examined using x-ray diffraction, scanning electron microscopy. Ohmic behavior with linear current-voltage characteristics was observed following anneals at $900^{\circ}C$ for 90sec at a pressure of $3.4{\times}10^{-5}$ Torr. The Pt/Si/Ti films was measured lower value of the specific contact resistance by the annealing process, and the contact resistances were improved more than one order compared to Ti contact the annealed sample. Scanning electron microscopy shows that the Pt layer effectively reduce the oxidation of Ti films. And results are obtained as $4.6{\times}10^{-4}$ ohm/$cm^2$ for a Pt/Ti metal structure after a vacuum annealing at $900^{\circ}C$ for 90sec. Titanium has a relatively high melting point, thus Ti-based metal contacts were attempted in this study.