• 한국재료학회지
• /
• 제20권5호
• /
• pp.271-277
• /
• 2010

In this paper two aspects of the percolation and conductivity of carbon black-filled polyethylene matrix composites will be discussed. Firstly, the percolation behavior, the critical exponent of conductivity of these composites, are discussed based on studying the whole change of resistivity, the relationship between frequency and relative permittivity or ac conductivity. There are two transitions of resistivity for carbon black filling. Below the first transition, resistivity shows an ohmic behavior and its value is almost the same as that of the matrix. Between the first and second transition, the change in resistivity is very sharp, and a non-ohmic electric field dependence of current has been observed. Secondly, the electrical conduction property of the carbon black-filled polyethylene matrix composites below the percolation threshold is discussed with the hopping conduction model. This study investigates the electrical conduction property of the composites below the percolation threshold based on the frequency dependence of conductivity in the range of 20 Hz to 1 MHz. There are two components for the observed ac loss current. One is independent of frequency that becomes prevalent in low frequencies just below the percolation threshold and under a high electrical field. The other is proportional to the frequency of the applied ac voltage in high frequencies and its origin is not clear. These results support the conclusion that the electrical conduction mechanism below the percolation threshold is tunneling.

• 센서학회지
• /
• 제16권4호
• /
• pp.259-262
• /
• 2007

This paper describes the electrical characteristics of polycrystalline (poly) 3C-SiC thin film diodes, in which poly 3C-SiC thin films on n-type and p-type Si wafers, respectively, were deposited by APCVD using HMDS, $H_{2}$, and Ar gas at $1150^{\circ}C$ for 3 hr. The schottky diode with Au/poly 3C-SiC/Si (n-type) structure was fabricated. Its threshold voltage ($V_{bi}$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_{D}$) value were measured as 0.84 V, over 140 V, 61 nm, and $2.7{\times}10^{19}cm^{-3}$, respectively. Moreover, for the good ohmic contact, Al/poly 3C-SiC/Si (n-type) structure was annealed at 300, 400, and $500^{\circ}C$, respectively for 30 min under the vacuum condition of $5.0{\times}10^{-6}$ Torr. Finally, the p-n junction diodes fabricated on the poly 3C-Si/Si (p-type) were obtained like characteristics of single 3CSiC p-n junction diode. Therefore, poly 3C-SiC thin film diodes will be suitable for microsensors in conjunction with Si fabrication technology.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.85.1-85.1
• /
• 2011

In this study, Grafoil$^{TM}$ which has comparable electric resistance and chemical stability but is flexible, fragile, and cheap material was adopted as bipolar plates for proton exchange membrane fuel cell(PEMFC) having only one straight line flow channel. Because of its flexibility, pressurizations of cell with various pressures showed different operating characteristics compared to ordinary graphite-used PEMFC. While performances of both cells decreased as these were pressurized, investigation of ohmic and faradaic resistance by electrochemical impedance measurement indicated different tendency of change. Ohmic resistance of graphite-used cell increased with increasing pressure, which is reversed in Grafoil$^{TM}$-used cell. It is speculated that effective chemical reaction area is decreased with increasing pressure in case of graphite-used one, but because of flexible property of Grafoil$^{TM}$, gas diffusion layer in Grafoil$^{TM}$-used cell was well-activated. Different rate of change of faradaic resistances in both cells support this supposition. However, although optimum point of pressurization is found, it is required to investigate other operating conditions because of low performance compared to graphite-used cell.

• 한국세라믹학회지
• /
• 제51권4호
• /
• pp.357-361
• /
• 2014

An Ni-Fe/YSZ core-shell structured anode for uniform microstructure and catalytic activity was synthesized. Flat tubular segmented-in-series solid oxide fuel cell-stacks were prepared by decalcomania method using synthesized anode powder. The Ni-Fe/YSZ core-shell anode exhibited better electrical conductivity than a commercially available Ni-YSZ cermet anode. Also power output increased by 1.3 times with a higher open circuit voltage. These results can be attributed to the uniformly distributed Ni particles in the YSZ framework. The impedance spectra of a Ni-Fe/YSZ core-shell anode showed comparable reduced ohmic resistance similar to those of the commercially available Ni-YSZ cermet anodes.

• Journal of Magnetics
• /
• 제10권2호
• /
• pp.66-70
• /
• 2005

The junction properties between the ferromagnet (FM) and two-dimensional electron gas (2DEG) system are crucial to develop spin electronic devices. Two types of 2DEG layer, InAs and GaAs channel heterostructures, are fabricated to compare the junction properties of the two systems. InAs-based 2DEG layer with low trans-mission barrier contacts FM and shows ohmic behavior. GaAs-based 2DEG layer with $Al_2O_3$ tunneling layer is also prepared. During heat treatment at the furnace, arsenic gas was evaporated and top AlAs layer was converted to aluminum oxide layer. This new method of forming spin injection barrier on 2DEG system is very efficient to obtain tunneling behavior. In the potentiometric measurement, spin-orbit coupling of 2DEG layer is observed in the interface between FM and InAs channel 2DEG layers, which proves the efficient junction property of spin injection barrier.

• 한국분무공학회지
• /
• 제22권2호
• /
• pp.69-79
• /
• 2017

When designing a redox flow battery system, compression of battery stack is required to prevent leakage of electrolyte and to reduce contact resistance between cell components. In addition, stack compression leads to deformation of the porous carbon electrode, which results in lower porosity and smaller cross-sectional area for electrolyte flow. In this paper, we investigate the effects of electrode compression on the cell performance by applying multi-dimensional, transient model of all-vanadium redox flow battery (VRFB). Simulation result reveals that large compression leads to greater pressure drop throughout the electrodes, which requires large pumping power to circulate electrolyte while lowered ohmic resistance results in better power capability of the battery. Also, cell compression results in imbalance between anolyte and catholyte and convective crossover of vanadium ions through the separator due to large pressure difference between negative and positive electrodes. Although it is predicted that the battery power is quickly improved due to the reduced ohmic resistance, the capacity decay of the battery is accelerated in the long term operation when the battery cell is compressed. Therefore, it is important to optimize the battery performance by taking trade-off between power and capacity when designing VRFB system.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.145-145
• /
• 2008

갈륨-질화물(GaN) 기반의 고속전자이동도 트랜지스터(high electron mobility transistor, HEMT)는 최근 마이크로파 또는 밀리미터파 등의 차세대 고주파용 전력소자로 각광받고 있다. AlGaN/GaN HEMT는 이종접합구조(heterostructure) 로부터 발생하는 이차원 전자가스(two-dimensional electron gas, 2DEG) 채널을 이용하여 높은 전자 이동도, 높은 항복전압 및 우수한 고출력 특성을 얻는 것이 가능하다. AlGaN/GaN HEMT에서 ohmic 전극 부분과 채널이 형성되는 부분과의 거리에 의한 저항의 성분을 줄이고 전자의 터널링의 확률을 증가시키기 위해서 recess된 구조가 많이 사용되고 있다. 그러나 이 구조에서는 recess된 소스와 드레인에 의해 AlGaN층의 제거로 AlGaN층의 두께에 영향을 미치며 그에 따라 채널에 생성되는 전자의 농도를 변화시키게 된다. 본 논문에서는 소스와 드레인의 Trench 구조를 제안하였다. ohmic 전극 부분과 채널간의 거리의 감소로 특성을 향상시켜서 recess 구조의 장점이 유지된다. 그리고 recess되는 소스와 드레인 영역에서 AlGaN층을 전체적으로 제거하는 것이 아니고 Trench 즉 일부분만 제거하면서 AlGaN층의 두께의 변화에 따른 문제점도 줄일 수 있다. 따라서 이러한 전극 부분을 Trench구조화 시킨 AlGaN/GaN HEMT의 DC특성을 $ATLAS^{TM}$를 이용하여 전산모사하고 최적화된 구조를 제안하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.25-26
• /
• 2008

Electrical properties of Pt/Ti/Au/Pt contacts to n-GaAs were characterized as the V/III ratio of GaAs grown by metalorganic chemical vapor deposition were 25, 50, and 100, respectively. The samples have been annealed during 30sec at 350 and $450^{\circ}C$ in rapid thermal annealing, and those specific contact resistance investigated by using transmission line method. According to experimental results, the specific contact resistance between p-metal and GaAs was decreased as the V/III ratio was lower. These results indicate that Si doping concentration of GaAs increased as the vacancy of V-series of GaAs was high.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.1014-1018
• /
• 2007

We have demonstrated the enhancement of the power efficiency and device lifetime of organic light-emitting diodes (OLEDs) by introducing the ETL 1 / ETL2 (composite ETL) structure between EML and cathode and the HIL1 (composite HIL) / HIL2 between anode and HTL. Compared to reference devices retaining conventional architecture, novel OLED structure shows an outstanding EL efficiency that is 1.6 times higher (${\sim}4.5$ lm/w versus ${\sim}$ 2.71 lm/w for the reference device) and lower driving voltage $({\bigtriangleup}V>1V)$, but also a longer lifetime and smaller operating voltage drift over time. It is suggested in this work that the device performance can be improved by in-situ ohmic contact through novel electron controlled structure and reduction of charge accumulation in the interface through composite HIL

• 대한전기학회논문지
• /
• 제44권12호
• /
• pp.1610-1616
• /
• 1995

The (Sr$_{1-x}$ .Ca$_{x}$)TiO$_{3}$(0.05.leq.x.leq.0.2) ceramics were fabricated to form semiconducting ceramics by sintering at about 1350[.deg. C] in a reducing atmosphere (N$_{2}$ gas). After being fired in a reducing atmosphere, metal oxides, CuO, was painted on the both surface of the specimens to diffuse to the grain boundary. They were annealed at 1100[.deg. C] for 2 hours. The 2nd phase formed by thermal diffusing from the surface lead to a very high apparent dielectric constant. The results of the capacitance-valtage measurements indicated that the grain boundary was composed of the continuous insulating layers. The capacitance is almost unchanged below about 20[V], but decreased slowly over 20[V]. The conduction mechanism of the specimens observed in the temperature range of 25~125[.deg. C], and is divided into three regions having different mechanism as the current increased: the region I below 200[V/cm] shows the ohmic conduction. The region II between 200[V/cm] and 2000[V/cm] can be explained by the Poole-Frenkel emission theory, and the region III above 2000[V/cm] is dominated by the tunneling effect.ct.