• Journal of Chest Surgery
• /
• v.54 no.3
• /
• pp.186-190
• /
• 2021

Background: Pre-lifting of the sternum marked a major turning point in pectus excavatum repair. The author developed the crane technique in 2002 and successfully applied it to more than 2,000 cases using sternal wire stitching. However, blind sternal suturing limited the use of the wire-stitch crane. We propose a novel screw for sternal lifting as a new tool for the crane technique. Methods: We developed a screw system strong enough to withstand the pressure needed for sternum lifting. The screw was designed to have a broader thread to hold the bony tissue securely. The screw's sustaining power was tested using the torsion, driving torque, and axial pull-out tests in a polyurethane block and ex-vivo porcine sternum. Results: The screws were easily driven into the sternum, and the head of the screw was connectable to the table-mounted retractor. In the torsion test, the 2° offset torsional yield was 4.53 N·m (reference value, 1 N·m). In the polyurethane block driving torque test, the maximum torque was 0.98 N·m (reference value, 0.70 N·m). The axial pull-out test was 446 N (reference value, 100 N). The maximum pull-out resistance in the ex-vivo porcine sternum model was 1,516 N. Conclusion: The screw crane was strong enough to sustain the chest wall weight to be lifted. Thus, the screws could effectively replace the sternal wire stitching in crane pre-lifting of the sternum. We expect that application of the screw-crane will be easy and that it will improve the safety and success rate of pectus repair surgery.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.221-221
• /
• 2012

Small-molecule organic photovoltaic cells have recently attracted growing attention due to their potential for the low-cost fabrication of flexible and lightweight solar modules. The PVP/Ag nanoparticles were synthesized by the reaction of poly vinylpyrrolidone (PVP) and silver nitrate at $150^{\circ}C$. In the reaction, the size of the nanoparticles was controlled by relative mole fractions between PVP and Ag. The PVP/Ag nanoparticles with various sizes were then spin coated on the patterned ITO glass prior to the deposition of the PEDOT:PSS hole transport layer. The scattering of the incident light caused by these incorporated nanoparticles resulted in an increase in the path length of the light through the active layer and hence the enhancement of the light absorption. This scattering effect increased as the size of the nanoparticles increased, but it was offset by the decrease in total transmittance caused by the non-transparent nanoparticles. As a result, the maximum power conversion efficiency, 0.96% which was the value enhanced by 14% compared to the cell without incorporation of nanoparticles, was obtained when the mole fraction of PVP:Ag was 24:1 and the size of the nanoparticles was 20~40 nm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2246-2253
• /
• 2011

This paper presents the error correction method of magnetic position sensor using recursive least square method (RLSM) with forgetting factor. Magnetic position sensor is proposed for linear position detection of the linear motor which has tooth shape stator, consists of permanent magnet, iron core and linear hall sensor, and generates sine and cosine waveforms according to the movement of the mover of the linear motor. From the output of magnetic position sensor, the position of the linear motor can be detected using arc-tan function. But the variation of the air gap between magnetic position sensor and the stator and the error in manufacturing process can cause the variation in offset, phase and amplitude of the generated waveforms when the linear motor moves. These variations in sine and cosine waveforms are changed according to the current linear motor position, and it is very difficult to compensate the errors using constant value. In this paper, the generated sine and cosine waveforms from the magnetic position sensor are compensated on-line using the RLSM with forgetting factor. And the speed observer is introduced to reduce the effect of uncompensated harmonic component. The approaches are verified by some simulations and experiments.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.221-224
• /
• 2005

This paper discribes the nonlinear distortion of a pHEMT power amplifier. In the paper, we have used some commercially available power amplifiers for analyzing the relationship between the $IMD_3$ and ACPR for wireless LAN. And the $IMD_3$ results using two-tone test have been compared with ACPR to satisfy the requited 802.11g standard ACPR value. Measurement result shows that $IMD_3$ of 20MHz tone-spacing need to be more than 18.45dBc for power amplifiers. The WCDMA signal is fed into the power amplifier, for analyzing relationship between the asymmetrical $IMD_3$ and ACLR. With measurement result, the asymmetrical $IMD_3$ characteristic has increased with the increase of two-tone spacing. $IMD_3$ measurement result with maximum 20MHz of the two-tone spacing, shows that the difference between $IMD_3(lower)$ and $IMD_3(upper)$ is about 7dB. And the measured ACLR shows 5dB difference at -4MHz and +4MHz offset from center frequency.

• Journal of electromagnetic engineering and science
• /
• v.4 no.4
• /
• pp.156-161
• /
• 2004

The MMIC cascode VCO is designed, fabricated, and measured for Ku-band Low Noise Blcok(LNB) system using InGaP/GaAs HBT technology. The phase noise of -116.4 dBc/Hz at 1 MHz offset with output power of 1.3 dBm is obtained at 11.526 GHz by applying 3 V and 11 mA, which is comparatively better characteristics than compared with the different configuration VCOs fabricated with other technologies. The simulated results of oscillation frequency and second harmonic suppression agree with the measured results. The phase noise is improved due to the use of the smallest value of inductor in frequency determining network and the InGaP ledge function of the technology. The chip size of $830\time781\;{\mu}m^2$ is also achieved.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.604-607
• /
• 2005

All CCD pixels do not react uniformly even if the light of same radiance enters into the camera. This comes from the different camera optical characteristics, the read-out characteristics, the pixel own characteristics and so on. Usually, the image data of satellite camera can be corrected by the various image-processing methods in the ground. However, sometimes, the in-orbit correction is needed to get the higher quality image. Especially high frequency pixel correction in the middle of in-orbit mission is needed because the in-orbit data compression with the high frequency loss is essential to transmit many data in real time due to the limited RF bandwidth. In this case, this high frequency correction can prevent have to have any unnecessary high frequency loss. This in-orbit correction can be done by the specific correction table, which consists of the gain and the offset correction value for each pixel. So, it is very important to get more accurate correction table for good correction results. This paper shows the new algorithm to get accurate pixel correction table. This algorithm shall be verified theoretically and also verified with the various simulation and the test results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.182-193
• /
• 2000

Several metrics have been used in crash discrimination algorithms in order to have timely air bag deployment during all frontal crash modes. However, it is still challengine to have timely air bag deployment especially during the oblique, the pole and the underride crash mode. Therefore, in this paper a new crash discrimination algorithm was proposed, using the absolute value of the deceleration change multiplied by the velocity change as a metric, and processing the metric as a function of the velocity change. The new algorithm was applied for all frontal crash modes of a minivan and a sports utility vehicle, and it resulted in timely air bag deployment for all frontal crash modes including the oblique, the pole and the underride crash mode. Moreover, it was proposed that an accelerometer be installed at each side of the rails, rockers or pillars to assess the crash severity of each side and to deploy the frontal air bags at different time especially during an asymmetric crash such as an oblique and an offset crash. As an example, the deceleration pulses measured at the left and right B-pillar·rocker locations were processed through the new algorithm, and faster time-to-fires were obtained for the air bag at the struck side for the air bag at the other side.

• Archives of design research
• /
• v.14 no.4
• /
• pp.157-165
• /
• 2001

The method to make ceramic pigments for 4 colour instead of ink in the process of the of set-printing and put them on the decal paper in the ceramic industry has been used to produce complicated images such as photographs or famous masterpieces. Offset-printing which is the production method for mass production, had enough worth to suffer the past high price of the production line. But today it is not suitable for the production method of small quantity and many kinds corresponding to needs for the various tastes and designs of consumers. Therefore I will put 4 colour printing method on the silkscreen, handiwork, suitable for the production method for small quantities and many variations to develop the methods that permit to cost effectively reproduce complex, high resolution, multicolor images. The study is expected to give value to ceramists who do various works and to be offered as the foundation in the field of design and expression.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2107-2113
• /
• 2014

Particle filtering (PF) has shown its outperforming results compared to that of classical Kalman filtering (KF), particularly for highly nonlinear problems. However, PF may not be universally superior to the extended KF (EKF) although the case (i.e. an example that the EKF outperforms PF) is seldom reported in the literature. Particularly, PF approaches show degraded performance for problems where the state noise is very small or zero. This is because particles become identical within a few iterations, which is so called particle impoverishment (PI) phenomenon; consequently, no matter how many particles are employed, we do not have particle diversity regardless of if the impoverished particle is close to the true state value or not. In this paper, we investigate this PI phenomenon, and show an example problem where a classical KF approach outperforms PF approaches in terms of mean squared error (MSE) criterion. Furthermore, we compare the processing speed of the EKF and PF approaches, and show the better speed performance of classical EKF approaches. Therefore, PF approaches may not be always better option than the classical EKF for nonlinear problems. Specifically, we show the outperforming result of unscented Kalman filter compared to that of PF approaches (which are shown in Fig. 7(c) for processing speed performance, and Fig. 6 for MSE performance in the paper).

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.10
• /
• pp.56-62
• /
• 2014

When fault currents contain decaying DC offset, the peak value of the fault current in the first cycle of the fault period is higher than the fault current during the steady-state period. To reduce the asymmetric fault current, this paper proposes an operation scheme using the series connection of two hybrid type Superconducting Fault Current Limiters (SFCLs) : an auxiliary SFCL and a main SFCL. The proposed method calculates the fault angle by comparing the zero-crossing time with fault detection time. According to the fault angle calculated, an auxiliary SFCL operates to reduce an asymmetric fault current during half a cycle after fault occurrence. After this process, the fault current is limited by a main SFCL. To confirm the usefulness of the proposed method, case studies using Electro-Magnetic Transients Program (EMTP)/Alternative Transient Program (ATP) Draw are perfomed.