• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.11 s.102
• /
• pp.1075-1085
• /
• 2005

The purpose of this paper is to design the architecture for synchronization of MB-OFDM UWB system that is being processed the standardization for Alt-PHY of WPAN(Wireless Personal Area Network) at IEEE802.15.3a and to analyze the implementation loss due to 4 parallel synchronization architecture for design or link margin. First an overview of the MB-OFDM UWB system based on IEEE802.15.3a Alt-PHY standard is described. The effects of non-ideal transmission conditions of the MB-OFDM UWB system including carrier frequency offset and sampling clock offset are analyzed to design a full digital architecture for synchronization. The synchronization architecture using 4-parallel structure is then proposed to consider the VLSI implementation including algorithms for carrier frequency offset and sampling clock offset to minimize the effects of synchronization errors. The overall performance degradation due to the proposed synchronization architecture is simulated to be with maximum 3.08 dB of the ideal receiver in maximum carrier frequency offset and sampling clock offset tolerance fir MB-OFDM UWB system.

• Korean Journal of Remote Sensing
• /
• v.34 no.3
• /
• pp.495-506
• /
• 2018

Global interest in climate change and sea level rise has led to active research on the velocities of glaciers. In studies about the velocity of glaciers, in-situ measurements can obtain the most accurate data but have limitations to acquire periodical or long-term data. Offset tracking using SAR is actively being used as an alternative of in-situ measurements. Offset tracking has a limitation in that the accuracy of observation is lower than that of other observational techniques, but it has been improved by recent studies. Recent studies in the $Uv{\hat{e}}rsbreen$ glacier area have shown that glacier altitudes decrease at a rate of 1.5 m/year. The glacier displacement velocities in this region are heavily influenced by climate change and can be important in monitoring and forecasting long-term climate change. However, there are few concrete examples of research in this area. In this study, we applied the improved offset tracking method to observe the two-dimensional velocity in the $Uv{\hat{e}}rsbreen$ glacier. As a result, it was confirmed that the glacier moved at a maximum rate of 133.7 m/year. The measruement precisions for azimuth and line-of-sight directions were 5.4 and 3.3 m/year respectively. These results will be utilized to study long-term changes in elevation of glaciers and to study environmental impacts due to climate change.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.2A
• /
• pp.176-186
• /
• 2006

In this paper, we propose an enhanced symbol detector algorithm for 2.45GHz LR-WPAN(Low-Rate Wireless Personal Area Network) receiver. Because the frequency offset of $\pm$80ppm on 2.45GHz band is recommended in IEEE 802.15.4 LR-WPAN(Low-Rate Wireless Personal Area Network) specification, a symbol detector algorithm having stable operation in the channel environment with large frequency offset is required. For robustness to the frequency offset, non-coherent detection-based symbol detector algorithm is typically applied in the LR-WPAN receiver modem. However, the noncoherent symbol detector has increased performance degradation and hardware complexity due to squaring loss of I/Q squaring operation. Therefore we propose a coherent detection-based symbol detector algorithm with frequency offset compensation using a preamble symbol. The proposed algorithm is more suitable for LR-WPAN receiver aimed at low-cost, low-power and low-complexity than the non-coherent symbol detector, since it can reduce performance degradation due to squaring loss of I/Q squaring operation and implementation complexity. Simulation results show that the proposed algorithm has performance improvement of about 1dB in various channel environments.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.3
• /
• pp.278-285
• /
• 2012

A digital readout IC for capacitive sensors is presented. Digital capacitance readout circuits suffer from static capacitance of sensors, especially single-ended sensors, and require large passive elements to cancel such DC offset signal. For this reason, to maximize a dynamic range with a small die area, the proposed circuit features digital filters having a coarse and fine compensation steps. Moreover, by employing switched-capacitor circuit for the front-end, correlated double sampling (CDS) technique can be adopted to minimize low-frequency device noise. The proposed circuit targeted 8-kHz signal bandwidth and oversampling ratio (OSR) of 64, thus a $3^{rd}$-order ${\Delta}{\Sigma}$ modulator operating at 1 MH was used for pulse-density-modulated (PDM) output. The proposed IC was designed in a 0.18-${\mu}m$ CMOS mixed-mode process, and occupied $0.86{\times}1.33mm^2$. The measurement results shows suppressed DC power under about -30 dBFS with minimized device flicker noise.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.12
• /
• pp.3018-3025
• /
• 2000

It is possible to shorten developing process by making model using polyurethane foam in the area of automobile development process, etc. However, this skill is too difficult to be of practical use because machining is not easy due to characteristic of polyurethane foam. Domestic and foreign automobile company use clay, polyurethane foam. etc,, those are easy to handle and to make model after completing design sketch. But these materials is difficult to the machined and be worked by humans hand, There are so many difficult problem for machining by making model using polyurethane foam since cutting of elastic body like polyurethan foam has never been studied. Therefore, in this study, it is investigated to measured cutting force that is generated in case of polyurethane foam machining, and to make systematize tool compensation of polyurethane foam cutting work on automobile model by modification of tool offset method on existing steel.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.698-704
• /
• 2013

The image process for image enhancement applies differently the same algorithm for each application. So, the optimized value for each application is required. In this paper, the X-ray medical image using a high-pass filter was improved edges. The result image was improved edge and the contrast of flat area using a constant multiplier and offset. Therefore, the high-frequency emphasis filter optimized for medical image is required. These optimized values are the gaussian high-pass filter, the distance of cutoff frequency=0.05 and offset=0.5. From the result of optimaized simulation, The proposed method has enhanced contrast and edge of the image in the contrast of existing mothods.

• Journal of electromagnetic engineering and science
• /
• v.9 no.1
• /
• pp.25-31
• /
• 2009

This paper describes CMOS VCO circuit design procedures and techniques for multi-band/multi-standard RF transceivers. The proposed techniques enable a 4 GHz CMOS VCO to satisfy all requirements for Quad-band GSMIEDGE and WCDMA standards by achieving a good trade-off among important specifications, phase noise, power consumption, modulation performance, and chip area efficiency. To meet the very stringent GSM T/Rx phase noise and wide frequency range specifications, the VCO utilizes bond-wire inductors with high-quality factor, an 8-bit coarse tune capbank for low VCO gain(30$\sim$50 MHz/V) and an on-chip $2^{nd}$ harmonic noise filter. The proposed VCO is implemented in $0.13{\mu}m$ CMOS technology. The measured tuning range is about 34 %(3.17 to 4.49 GHz). The VCO exhibits a phase noise of -123 dBc/Hz at 400 kHz offset and -145 dBc/Hz at 3 MHz offset from a 900 MHz carrier after LO chain. The calculated figure of merit(FOM) is -183.5 dBc/Hz at 3 MHz offset. This fully integrated VCO occupies $0.45{\times}0.9\;mm^2$.

• Spatial Information Research
• /
• v.23 no.2
• /
• pp.11-20
• /
• 2015

Abstract Monitoring is the most critical element in implementing "forest carbon offset project" to enhance the visibility of CSR (Corporate Social Responsibility) in North Korea. This study is intended to explore monitoring potential in terms of forest carbon offset project using satellite image for Baekdu mountain of North Korea. The permanent record of standard satellite remote sensing system demonstrated its capability of presenting area-wide visual evidences of monitoring conditions in Mt. Baekdu mountain of North Korea (site suitability, carbon stock by forest biomass growth, carbon emission by forest biomass loss, deforestation and degradation, environmental, social and economic impact specified in the Carbon Sequestration Law). It doesn't seem very difficult to comply with monitoring requirements for "the forest carbon offset project" due to the probative value of satellite data. Therefore, it could be considerable or realistic approach to utilize CSR based forest carbon offset project as a point of reform and open-door in North Korea. It is anticipated that this research output could be used as a valuable reference for Korea-based enterprises to ensure monitoring potentials using satellite image in exploring forest carbon offset project sites in North Korea.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.4
• /
• pp.321-329
• /
• 2002

Bending moments results from offset overloading of dental implant, which may cause stress concentrations to exceed the physiological capacity of cortical bone and lead to various kinds of mechanical failures. The purpose of this study was to compare the distributing pattern of stress on the finite element models with the different angulated placement of dental implant in mandibular posterior missing areas. The three kinds of finite element model, were designed according to 3 main configurations: Model 1(parallel typed placement of 2 fixtures), Model 2(15. distal angulated placement of one fixture on second molar area), Model 3(15. mesial angulated placement of one fixture on second molar area). The cemented crowns for mandibular first and second molars were made on the two fixtures (4mm 11.5). Three-dimensional finite element models by two fixtures were constructed with the components of the implant and surrounding bone. A 200N vertical static load were applied to the center of central fossa and the point 2mm apart from the center of central fossa on each model. The preprocessing, solving and postprocessing procedures were done by using FEM analysis software NISA/DISPLAY IV Version 10.0((Engineering Mechanics Research Corporation, USA). Von Mises stresses were evaluated and compared in the supporting bone, fixtures, and abutment. The results were as following : (1) Under the point loading at the central fossa, the direction of angulated fixture affected the stress pattern of implants. (2) Under the offset loading, the position of loading affected more on the stress concentration of implants compare to the angulated direction of implants. The results had a tendency to increase the stress on the supporting bone, fixture and screw under the offset loads when the placement angulation of implant fixture is placed toward mesial or distal direction. In designing of the occlusal scheme for angulated placement, placing the occlusal contacts axially during chewing appears to have advantages in a biomechanical viewpoint.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.25 no.3
• /
• pp.17-28
• /
• 2022

We evaluated the effect of CO₂ offsetting by estimating changes in carbon uptake under various forest management scenarios and proposed forest management strategies to achieve carbon neutrality. Paju and Goseong, which have relatively large forest areas but different industrial characteristics, were selected for the study sites. The current state of forest distribution was analyzed using forest type maps and aerial photographs, and the amount of carbon uptake was calculated using the equation presented by the IPCC Guidelines for National Greenhouse Gas Inventories and the national emission/absorption coefficients from the Korea National Greenhouse Gas Inventory Report. As of 2015, the forest carbon absorption in Paju and Goseong was 49,931 t/yr and 94,225 t/yr, respectively, and the annual carbon absorption per unit area was 2.28 t/ha/yr and 2.16 t/ha/yr. Under the forest management scenarios, the annual maximum carbon absorption per unit area is estimated to increase to 5.68 t/ha/yr in Paju and 4.22 t/ha/yr in Goseong, and this absorption would increase further if urban forests were additionally created. Even if the current forests of Paju and Goseong are maintained as they are, emissions from electricity use can be sufficiently offset. However, by applying appropriate forest management strategies, emissions from sectors other than electricity use could be offset. This study can be applied to the establishment of carbon absorption strategies in the forest sector to achieve carbon neutrality.