• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.5
• /
• pp.899-905
• /
• 2001

The damage behavior of soda-lime glass was studied due to a steel ball of 1mm and 2mm at oblique impact test. The thickness of glass specimen were 3mm and 5mm and oblique degrees of impact were 90$^{\circ}$,70$^{\circ}$ and 50$^{\circ}$. After the steel ball impact test, the crack patterns were investigated using a stereo-microscope. In addition, the finite element method was performed to analyze the stresses distribution and variation in the oblique impacted glass by steel ball. As a result of the impact test, the crack length of 90$^{\circ}$impacted glass was the largest and that of 50$^{\circ}$impacted glass was the smallest. In particular, as the impact velocity and diameter of the steel ball increased, the difference of crack length was prominent. The finite element analysis showed the maximum principle stresses distribution in contact area of glass specimen. The result of analysis was accorded with the crack growth behavior by the oblique impact test.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.2
• /
• pp.228-238
• /
• 2002

Using the dynamic explicit program NET3D, oblique impact between long rod penetrator and metallic plate was analyzed. Compared with an experiment and AUTODYN-3D analysis result, the accuracy of NET3D program was examined. It was proved that NET3D program could analyze comparatively exactly oblique impact phenomenon between long rod penetrator and metallic plate. The final deformed configuration of penetrator predicted by NET3D program was more close to experimental result than commercial program AUTODYN-3D. But, in order to increase the reliability of NET3D program in the simulation of tensile fracture phenomenon, the additional research is required.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.135-142
• /
• 2007

MADYMO human model with the detail neck was used to investigate the reaction force of neck and neck injury from rear impact directions. In the validation simulation, head acceleration, thorax acceleration and the global kinematics of the head and neck were correlated well with experimental data. Acceleration data from three 15 km/h low speed car rear impact pendulum tests(rear-end, offset, oblique) were used to simulate the model. In the simulation results, the reaction force on the facet joint and discs in the oblique rear impact were higher than rear-end, offset rear impacts. Further research is still needed in order to neck injury analysis about different crash parameters.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.3
• /
• pp.576-585
• /
• 2002

A three-dimensional Lagrangian explicit time-integration finite element code for analyzing the dynamic impact phenomena was developed. It uses four node tetrahedral elements. In order to consider the effects of strain rate hardening, strain hardening and thermal softening, which are frequently observed in high-velocity deformation phenomena, Johnson-Cook model is used as constitutive model. For more accurate and robust contact force computation, the defense node contact algorithm was adopted and implemented. In order to evaluate the performance of the newly developed three-dimensional hydrocode NET3D, numerical simulations of the oblique impact of mild steel plate by mild steel sphere were carried out. Ballistic limit about various oblique angle between 0 degree and 80 degree was estimated through a series of simulations with different initial velocities of sphere. Element eroding by equivalent plastic strain was applied to mild steel spheres and targets. Ballistic limits and fracture characteristics obtained from simulation were compared with experimental results conducted by Finnegan et al. From numerical studies, the following conclusions were reached. (1) Simulations could successfully reproduce the key features observed in experiment such as tensile failure termed "disking"at normal impacts and outwards bending of partially formed plus segments termed "hinge-mode"at oblique impacts. (2) Simulation results fur 60 degrees oblique impact at 0.70 km/s and 0.91 km/s were compared with experimental results and Eulerian hydrocode CTH simulation results. The Lagrangian code NET3D is superior to Eulerian code CTH in the computational accuracy. Agreement with the experimentally obtained final deformed cross-sections of the projectile is excellent. (3) Agreement with the experimental ballistic limit data, particularly at the high-obliquity impacts, is reasonably good. (4) The simulation result is not very sensitive to eroding condition but slightly influenced by friction coefficient.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.4 s.23
• /
• pp.5-13
• /
• 2005

The impact of a long-rod penetrator into oblique plates with combined obliquity and yaw is investigated. The study was done using a newly developed three dimensional dynamic and impact analysis code, which uses the explicit finite element method. Through the comparison of simulation result with experimental result and other code's result, the adaptability and accuracy of the developed code is evaluated under the complex situation in which yaw angle and oblique angle exist simultaneously. As a result of comparison, it has found that deformed shape, residual length and velocity, rotational velocity of long-rod show good agreement with experimental data. Through this study, the applicability and accuracy of the code as a metallic armour system design tool is verified.

• Journal of Auto-vehicle Safety Association
• /
• v.14 no.4
• /
• pp.100-105
• /
• 2022

Oblique car to car frontal impact is quite common on the road and series of studies have been done to realize this in the lab. At a certain angle of oblique crash a car (ego) is to travel at a speed of xkm/h to hit the other car(traffic) which is approaching to ego at a speed of ykm/h. Symmetry of the speed of two vehicles, x vs. y, is studied with respect to the impulse of the ego vehicle as well as occupant injury. If there is symmetry of speed of two vehicles, number of case studies needed to analyze the oblique frontal impact may decrease: ex. in the case of 30degree oblique crash 40km/h (ego) / 80km/h (traffic) will show the similar behavior as 80km/h (ego) / 40km/h (traffic) crash.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1426-1437
• /
• 2002

Using the Lagrangian explicit time-integration finite element code NET3D which can treat three-dimensional high-velocity impact problems, oblique penetration processes of long rod projectile with yaw against thin plate are simulated. Through the comparison of simulation result with experimental result and other code's computational result, the adaptability and accuracy of NET3D is evaluated under the complex situation in which yaw angle and oblique angle exist simultaneously. Main research contents to be handled in this paper include the followings. First, the accuracy and efficiency estimation of NET3D code result obtained from the oblique penetration simulations of long rod projectile with yaw against thin plate. Second, the effect of increasing impact velocity. Third, the effect of initial yaw for the spaced-plate target. Residual velocities, residual lengths, angular velocities, and final deformed configurations obtained from the NET3D computations are compared with the experimental results and other code's computational results such as Eulerian code MESA and Lagrangian code EPIC. As a result of comparisons, it has been found that NET3D code is superior to EPIC code and MESA code in the prediction capability of residual velocity and residual length of penetrator. The key features obtained from the experiment can be successfully reproduced through NET3D simulations. Throughout the study, the applicability and accuracy of NET3D as a metallic armor system design tool is verified.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.482-494
• /
• 2019

In this paper, the oblique water-entry impact of a vehicle with a disk cavitator is studied experimentally and numerically. The effectiveness and accuracy of the numerical simulation are verified quantitatively by the experiments in this paper and the data available in the literature. Then, the numerical model is used to simulate the hydrodynamic characteristics and flow patterns of the vehicle under different entry conditions, and the axial force is found to be an important parameter. The influences of entry angle, entry speed and cavitator area on the axial force are studied. The variation law of the force coefficient and the dimensionless penetration distance at the peak of the axial force are revealed. The research conclusions are beneficial to engineering calculations on the impact force of a vehicle with a disk cavitator over a wide range of water-entry parameters.

• Steel and Composite Structures
• /
• v.28 no.2
• /
• pp.179-194
• /
• 2018

Reliable and accurate method of computationally aided design processes of advanced thin walled structures in automotive industries are much essential for the efficient usage of smart materials, that possess higher energy absorption in dynamic compression loading. In this paper, most versatile components i.e., thin walled crash tubes with different geometrical profiles are introduced in view of mitigating the impact of varying cross section in crash behavior and energy absorption characteristics. Apart from the geometrical parameters such as length, diameter and thickness, the non-dimensionalized parameters of average forces which control the plastic bending moment for varying thickness has explored in view of quantifying its impact on the crashworthiness of the structure. The explicit finite element code ABAQUS is utilized to conduct the numerical studies to examine the effect of parametric modifications in crash behavior and energy absorption. Also the simulation results are experimentally validated. It is evident that the circular cross-sectional tubes are preferable as high collision impact shock absorbers due to their ability in withstanding axial and oblique impact loads effectively. Furthermore, the specific energy absorption (SEA), crash force efficiency (CFE), plastic bending moment, peak force responses and its impact for optimally tailoring a design to cater the crashworthiness requirements are investigated. The primary outcome of the study is to provide sufficient information on circular tubes for the use of energy absorbers where impact oblique loading is expected.

• The Journal of Korean Physical Therapy
• /
• v.28 no.2
• /
• pp.136-141
• /
• 2016

Purpose: In this study experiments were performed during 6 weeks with 40 adults, 20 subjects in the waist stabilization exercise with blood flow restriction group and 20 subjects in the waist stabilization exercise without blood flow restriction group, in order to determine the impact of waist stabilization exercise on White Area Index (WAI) followed by blood flow restriction. Methods: Thickness of external oblique abdominal muscle, internal oblique abdominal muscle, and transversus abdominis muscle, as well as density and WAI of external oblique abdominal muscle were measured, followed by performance of repeated ANOVA. Results: Significant difference in thickness of external oblique abdominal muscle according to periodical difference was observed between groups (p<0.05). Significant difference in thickness of internal oblique abdominal muscle and transversus abdominis muscle according to periodical difference was observed between groups (p<0.05). Significant difference in density and WAI of external oblique abdominal muscle according to periodical difference was observed between groups (p<0.05). Conclusion: In conclusion, significant difference was observed after waist stabilization exercise with blood flow restriction. These results can be used as basic data for future research on waist stabilization exercise and blood flow restriction exercise.