• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1425-1428
• /
• 2007

The amorphous IZO on flexible substrate (PC) shows similar electrical conductivity and optical transmittance with commercial ITO glass even though it was prepared at $<50\;^{\circ}C$. Moreover, it exhibits little resistance change during 5000 bending cycles, demonstrating good mechanical robustness. A green phosphorescent OLED fabricated on amorphous IZO on flexible PC shows maximum external quantum efficiency of ${\eta}_{ext}=13.7\;%$ and power efficiency of ${\eta}_p=32.7\;lm/W$, which are higher than a device fabricated on a commercial ITO on glass (${\eta}_{ext}=12.4%$ and ${\eta}_p=30.1\;lm/W$) and ITO on flexible PC (${\eta}_{ext}=8.5%$ and ${\eta}_p=14.1\;lm/W$).

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.1
• /
• pp.29-33
• /
• 2012

In this study, we have investigated the structural and electrical characteristics of IZO thin films deposited under hydrogen atmosphere on flexible substrate for the OLED (organic light emitting diodes) devices. For this purpose, PES was used for flexible substrate and IZO thin films were deposited by RF magnetron sputtering under hydrogen ambient gases (Ar, $Ar+H^2$) at room temperature. In order to investigate the influences of the hydrogen, the flow rate of hydrogen in argon mixing gas has been changed from 0.1sccm to 0.5sccm. All the samples show amorphous structure regardless of flow rate. The electrical resistivity of IZO films increased with increasing flow rate of $H^2$ under $Ar+H^2$. All the films showed the average transmittance over 85% in the visible range. The OLED device was fabricated with different IZO electrodes made by configuration of IZO/$\acute{a}$-NPD/DPVB/$Alq_3$/LiF/Al to elucidate the performance of IZO substrate. OLED devices with the amorphous-IZO (a-IZO) anode film show good current density-voltage-luminance characteristics. This suggests that flat surface roughness and low electrical resistivity of a-IZO anode film lead to more efficient anode material in OLED devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.114-118
• /
• 2006

We investigated the transient electroluminescence (EL) and modulation characteristics of red organic light-emitting diodes (OLEDs), which consist with 4-(dicyanomethylene)-2-i -propyl-6-(1,1,7,7-tetramethyljulolidyl-9-cnyl)-4H-pyran (DCJTI) and rubrene doped into tris(8-hydroxyquinoline)aluminum ($Alq_3$). The transient EL waveforms showed two components, the overshooting peak and constant component, indicating that the excess amount of accumulated charges simultaneously recombine at the onset moment. This overshooting effect reduced the rise time of transient EL and enhanced the optical output of OLEDs when the pulse voltage applied to the device. We demonstrated that the red OLEDs could be use for the high-speed switching application by driving at more than 100 MHz and transmitting the video signals utilized as the electro-optical conversion device

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.305-306
• /
• 2009

In this study, we have invastigated the recombination zone in the blue phosphorescent organic light-emitting devices with various partially doped structures. The basic device structure of the blue PHOLED was anode / hole injection layer (HIL) / hole transport layer (HTL) / emittingvastigated the recombination zone in the blue layer (EML) / hole blocking layer (HBL) / electron transport layer (ETL) / electron injection layer (EIL) / cathode. After the preparation of the blue PHOLED, the current density (J) - voltage (V) - luminance (L) and current efficiency characteristics were measured.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.903-906
• /
• 2003

Doping a small amount of a phosphorescent dye into an organic light-emitting diodes(OLED) can lead to a significant improvement in the device properties. The fluorescent host materials like TAZ, CBP have been used, but have a problem of rapid decay of efficiency at high current densities. To alleviate this problem, phosphorescent host was introduced. The whole configuration of OELD fabricated was ITO/a-NPD(50nm)/Zn $cluster:Ir(ppy)_{3}(30nm)/BCP{(10nm)/Alq_{3}(20nm)$ /Al:Li. The OLED showed high luminance (> 50,000 $cd/m^{2}$ ) and external efficiency(5.7%). At higher current densities, rapid decay of external quantum efficiency or host emission, which was frequently observed in the fluorescent host system, were not observed.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1361-1362
• /
• 2006

In this research We investigated the effect of UV/O3, $O_3$ treatments of Indium-tin oxide(ITO) surface on the performance of organic light emitting devices(OLEDs). The fundamental structure of OLEDs was ITO(anode) / TPD(Hole Transport Layer) / $Alq_3$ / Al(cathode). We performed UV/O3, $O_3$ treatments and found that both treatments enhanced the performance of OLEDs. Current-Voltage, Luminance-Voltage characteristics were measured at room temperature.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1876-1877
• /
• 2005

유기 전기 발광 소자(Organic Light-emitting Devices, OLEDs)의 발광 효율과 안정성을 향상시키고자 플라즈마 중합 장비를 이용해서 소자에 버퍼층(buffer layer)을 도입하였다. 플라즈마 중합 방법을 이용해서 성막된 PPMMA를 ITO와 정공 수송층 사이에 버퍼층으로 삽입하여 유기 전기 발광 소자를 제작하였고, 그 특성에 대하여 연구하였다. 기존에 사용되고 있는 버퍼층 공정에 비하여 공정의 단순화 및 비용절감의 효과를 기대할 수 있고, 전기-광학적 특성도 확인할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.147-147
• /
• 2015

The multilayer structure of the organic light emitting diode has merits of improving interfacial characteristics and helping carriers inject into emission layer and transport easier. There are many reports to control hole injection from anode electrode by using transition metal oxide as an anode buffer layer, such as V2O5, MoO3, NiO, and Fe3O4. In this study, we apply thin films of LiF which is usually inserted as a thin buffer layer between electron transport layer(ETL) and cathode, as an anode buffer layer to reduce the hole injection barrier height from ITO. The thickness of LiF as an anode buffer layer is tested from 0 nm to 1.0 nm. As shown in the figure 1 and 2, the luminous efficiency versus current density is improved by LiF anode buffer layer, and the threshold voltage is reduced when LiF buffer layer is increased up to 0.6 nm then the device does not work when LiF thickness is close to 1.0 nm As a result, we can confirm that the thin layer of LiF, about 0.6 nm, as an anode buffer reduces the hole injection barrier height from ITO, and this results the improved luminous efficiency. This study shows that LiF can be used as an anode buffer layer for improved hole injection as well as cathode buffer layer.

• Journal of Information Display
• /
• v.6 no.1
• /
• pp.28-32
• /
• 2005

The electronic structures of Al/RbF/tris-(8-hydroxyquinoline)aluminium ($Alq_3$) and $Al/CaF_2/Alq_3$interfaces were investigated using x-ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS). For both systems, the UPS showed a significant valence band shift following the deposition of the thin fluoride layers on $Alq_3$. However, the formation of gap state in valence region and the extra peak N 1s core level spectra showed different trends, suggesting that the alkali fluoride and alkali-earth fluoride interlayer have different reaction mechanisms at the interface between Al cathode and $Alq_3$. In addition, the deposition of Al has considerably less effect on the valence band shift compared to the deposition of both RbF and $CaF_2$. These results suggest that the charge transfer across the interface and the resulting gap state formation may have lesser effect on the enhancement of organic light-emitting device performance than the observed valence band shift, which is thought to lower the electron injection barrier.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.33-33
• /
• 2010

Electrical properties of organic light-emitting diodes (OLEDs) were simulated by S.co's program. The OLEDs have stable operating parameters, high luminance, and high efficiency in simulation. The AF stands for amorphous fluoropolymer in simulation, and it was used as a hole-injection layer. In the five structure of OLEDs, an AF layer is sandwiched between the hole-transport layer and the ITO layer to increase the external quantum efficiency. By considering organic light-emitting diodes using an optimal energy gap of AF, it could contribute to the improvement of the efficiency of the device in the simulation.