• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.182-185
• /
• 2003

Etching characteristics of (PB,Sr)$TiO_3$(PST) thin films Were investigated using inductively coupled chlorine based plasma system as functions of gas mixing ratio, RF power and DC bias voltage. It was found that increasing of Ar content in gas mixture' lead to sufficient increasing of etch rate and selectivity of PST to Pt. The maximum etch rate of PST film is 562 ${\AA}$/min and the selectivity of PST film to Pt is 0.8 at $Cl_2/(Cl_2+Ar)$ of 20 %. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.491-491
• /
• 2013

A novel plasma system has been developed for 3-dimensional modification of the carbon nano-powders. Improvement of dispersion of these nano materials are studied by plasma discharge, not using chemical modification. The plasma process is considered to great advantages over wet chemical process due to environmental, economic viewpoint, and uniformity over the treated volume. The uniform dispersion is a critical factor for these material's nano composite applications. Using this plasma system, graphene, carbon black, and CNT was treated and functionalized. Several key discharge conditions such as Ar/H2/O2 or Ar/H2/NH3 gas ratio, treatment time, power, feeder's vibration frequency are investigated. Hydrophobic of graphene has turned some more into hydrophilic by reaction test with water, electrophoresis, surface contact angle test, and turbidity analysis. The oxygen content ratio in the plasma treated CNT has increased about 3.7 times than the untreatedone. In the case of graphene and carbon black, the oxygen- and nitrogen- content has been enhanced average 10%. O-H (N-H) peak, C-O (C-N) peak, and C=O (C=N) peak data have been detected by FTIR measurement and intensified compared to before-plasma treatment due to O2 or NH3 content.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.11
• /
• pp.1533-1537
• /
• 2014

$WO_3/Ag/WO_3$ multilayer was researched by using RF magnetron sputtering with transparent electrode. Process gas flow ratio with $Ar/O_2$ were selected the optimum conditions at 70sccm/2sccm and $WO_3$ thin film at its conditions was appeared at transmittance about 80% in the visible light region to the average. $WO_3/Ag/WO_3$ multilayer thin films were fabricated from the same process condition which was the same gas flow ratio of Ar and $O_2$ $WO_3/Ag/WO_3$ thin films were appeared transmittance about 93% and sheet resistance about $6.41{\Omega}/{\square}$. From the SEM images, each thin films were appeared when $WO_3$ is 40nm and $O_2$ is 10nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.16-19
• /
• 2002

(Ba,Sr)TiO3(BST) thin film is an attractive material for the application in high-density dynamic random access memories (DRAMs) because of the high relative dielectric constant and small variation in dielectric properties with frequency. In this study, (Ba0.6,Sr0.4)TiO3 thin films on Pt/Ti/SiO2/Si substrates were deposited by a sol-gel method and the CF4/Ar inductively coupled plasma (ICP) etching behavior of BST thin films had been investigatedby varying the process parameters such as chamber pressure, ICP power, and substrate bias voltage. To analysis the composition of surface residue following etching BST films etched with different Ar/CF4 gas mixing ratio were investigated using x-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometer (SIMS).

• Applied Science and Convergence Technology
• /
• v.23 no.2
• /
• pp.90-96
• /
• 2014

Flexible $ZrO_2$ films as dielectric materials for high-energy-density capacitors were deposited on polyethylene terephthalate (PET) substrates by RF magnetron sputtering. The growth behavior, microstructure and electrical properties of the flexible $ZrO_2$ films were dependent on the sputtering pressure and gas ratio. Although $ZrO_2$ films were deposited at room temperature, all films showed a tetragonal crystalline structure regardless of the sputtering variables. The surface of the film became a surface with large white particles upon an increase in the $O_2/Ar$ gas ratio. The RMS roughness and crystallite size of the $ZrO_2$ films increased with an increase in the sputtering pressure. The electrical properties of the $ZrO_2$ films were affected by the microstructure and roughness. The $ZrO_2$ films exhibited a dielectric constant of 21~38 at 1 kHz and a leakage current density of $10^{-6}{\sim}10^{-5}A/cm^2$ at 300 kV/cm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.11-11
• /
• 2008

ZnO has a very large exciton binding energy (60 meV) as well as thermal and chemical stability, which are expected to allow efficient excitonic emission, even at room temperature. ZnO based electronic devices have attracted increasing interest as the backplanes for applications in the next-generation displays, such as active-matrix liquid crystal displays (AMLCDs) and active-matrix organic light emitting diodes (AMOLEDs), and in solid state lighting systems as a substitution for GaN based light emitting diodes (LEDs). Most of these electronic devices employ the electrical behavior of n-type semiconducting active oxides due to the difficulty in obtaining a p-type film with long-term stability and high performance. p-type ZnO films can be produced by substituting group V elements (N, P, and As) for the O sites or group I elements (Li, Na, and K) for Zn sites. However, the achievement of p-type ZnO is a difficult task due to self-compensation induced from intrinsic donor defects, such as O vacancies (Vo) and Zn interstitials ($Zn_i$), or an unintentional extrinsic donor such as H. Phosphorus (P) doped ZnO thin films were grown on c-sapphire substrates by radio frequency magnetron sputtering with various Ar/ $O_2$ gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio with out post-annealing. The P-doped ZnO films grown at a Ar/ $O_2$ ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of $10^{-17}cm^{-3}$ and $2.5cm^2/V{\cdot}s$, respectively. X-ray diffraction showed that the ZnO (0002) peak shifted to lower angle due to the positioning of $p^{3-}$ ions with a smaller ionic radius in the $O^{2-}$ sites. This indicates that a p-type mechanism was due to the substitutional Po. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction LEO showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.

• Membrane Journal
• /
• v.13 no.2
• /
• pp.73-80
• /
• 2003

Abstract: The surfaces of poly (methylpentene)(PMP) were modified by Af and $NH_3$ plasma treatment, and their effects on permeation characteristics were investigated. The mole ratio of O/C in the surface was increased with Ar plasma treatment and consequently the surface became hydrophilic because of the possible formation of -OH, -COOH and C=O. The surface treated by $NH_3$ plasma also became hydrophilic due to the formation of amine and/or amide groups. The $CO_2$ permeability and its actual selectivity over N_2$ were 182 baller and 6.17 for the optimum condition of Ar-30W-6min, while 144 Baller and 6.13 for that of $NH_3$-30 W-8 min.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.5
• /
• pp.33-37
• /
• 2003

This study was performed to investigate the deposition mechanism of SiO$_2$ by ArF excimer laser(l93nm) CVD with Si$_2$H$\_$6/ and N$_2$O gas mixture and evaluate laser CVD quantitatively by modeling. With ArF excimer laser CVD, thin films can be deposited at low temperature(below 300$^{\circ}C$), with less damage and good uniformity owing to generation of conformal reaction species by singular wavelength of the laser beam. In this study, new model of SiO$_2$ deposition process by laser CVD was introduced and deposition rate was simulated by computer with the basis on this modeling. And simulation results were compared with experimental results measured at various conditions such as reaction gas ratio, chamber pressure, substrate temperature and laser beam intensity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.375-378
• /
• 2002

We investigated the reduction of etching damage by additive O$_2$ in etching gas and recovery of etching damage by O$_2$ annealing. The PZT thin films were etched using additive Ar or O$_2$ into Cl$_2$/CF$_4$ gas mixing ratio of 8/2. In order to recover ferroelectric properties of PZT thin films after etching, the etched PZT thin films were annealed at 600 C in O$_2$ atmosphere for 10 min. The remanent polarization is decreased seriously and fatigue is accelerated in the PZT sample etched in Ar/(C1$_2$+CF$_4$) plasma, whereas these characteristics are improved in O$_2$/(Cl$_2$/CF$_4$). From x-ray photoelectron spectroscopy (XPS) analysis, the intensities of Pb-O, Zr-O and Ti-O peaks are changed and the etch byproducts such as metal chloride and metal fluoride are reduced by O$_2$ annealing. From electron probe micro analyzer (EPMA) and auger electron spectroscopy(AES), O$_2$ vacancy is observed after etching. In x-ray diffraction (XRD), the structure damage in the additive O$_2$ into C1$_2$/CF$_4$ is reduced and the improvement of ferroelectric behavioral annealed sample is consistent with the increase of the (100) and (200) PZT peaks.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.848-850
• /
• 1999

In this study, PZT etching was performed using planar inductively coupled Ar(20)/$Cl_2/BCl_3$ plasma, The etch rate of PZT film was 2450 $\AA/min$ at Ar(20)/$BCl_3$(80) gas mixing ratio and substrate temperature of $80^{\circ}C$. X-ray photoelectron spectroscopy (XPS) analysis for film composition was utilized. The chemical bond of PbO is broken by ion bombardment, and the peak of metal Pb in a Pb 4f peak begins to appear upon etching, decreasing Pb content faster than Zr and Ti. As increase content of additive $BCl_3$, the relative content of oxygen decreases rapidly. We thought that abundant Band BCl radicals made volatile oxy-compound such as $B_{x}O_{y}$ and/or $BClO_x$ bond. To understand etching mechanism, Langmuir probe and optical emission spectroscopy (OES) analysis were utilized for plasma diagnostic.