• Journal of Sensor Science and Technology
• /
• v.16 no.3
• /
• pp.240-245
• /
• 2007

AlN thin film for SAW filter application was deposited on (100) silicon, sapphire, $Si_{3}N_{4}$/Si, and $Al_{2}O_{3}$/Si substrates by reactive magnetron sputtering method, respectively. The structural characteristics were dependent on the structure of substrates. Scanning Electron Microscope (SEM), X-ray Diffraction (XRD) and Atomic Force Microscope (AFM) have been used to analyze structural properties and preferred orientation of AlN thin films. Preferred orientation and SAW characteristic of AlN were improved by insertion of $Al_{2}O_{3}$ buffer layer. Insertion loss of SAW devices using AlN/Si and AlN/$Al_{2}O_{3}$/Si were about 33.27 dB and 30.20 dB, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2288-2292
• /
• 2007

The catalytic activities of nickel-based catalysts were estimated for oxidizing acetaldehyde of VOCs exhausted from industrial facilities. The catalysts were prepared by sol-gel methods of SiO2 and SiO2-TiO2 as a xerogel followed by impregnating Al2O3 powder with the nickel nitrate precursor. The crystalline structure and catalytic properties for the catalysts were investigated by use of BET surface area, X-ray diffraction (XRD), Xray photoelectron spectroscopy (XPS) and temperature programmed reduction (TPR) techniques. These results show that nickel oxide is transformed to NiAl2O4 spinel structure at the calcination temperature of 400 °C in response to the steps with after- and co-impregnation of Al2O3 powder in sol-gel process. The NiAl2O4 could suppress the oxidation reaction of acetaldehyde by catalysts. The NiO is better dispersed on SiO2-TiO2/Al2O3 support than SiO2/Al2O3 and SiO2-TiO2-Al2O3 supports. From the testing results of catalytic activities for oxidation of acetaldehyde, Catalysts showed a big difference in conversion efficiencies with the way of the preparation of catalysts and the loading weight of nickel. The catalyst of 8 wt.% Ni/TiO2-SiO2/Al2O3 showed the best conversion efficiency on acetaldehyde oxidation with 100% conversion efficiency at 350 °C.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.224-228
• /
• 2000

Using a small amount of additives and amorphous Si₂N₂O powders, O-SiAlON ceramics have been hot-pressed and its microstructure and mechanical properties were investigated. Scandium oxide was demonstrated to be an effective densification additive for O-SiAlON. Amorphous Si₂N₂O was densified at relatively low temperatures and a microstructure with acicular grains was developed. Fine grains found in materials obtained from amorphous powders suggest that nucleation and crystallization of O-SiAlOH is relatively easy compared with the Si₃N₄-SiO₂reaction.

• Journal of the Korean Ceramic Society
• /
• v.37 no.4
• /
• pp.368-375
• /
• 2000

Fracture toughness of particulate composites of Al2O3/SiC, Al2O3/ZrO2 and Al2O3/ZrO2/SiC was analysed theoretically. According to the suggested particle bridging model for obtaining the R-curve height, the crack extension resistance for the long crack was linearly proportional to the residual calmping stress at the interface between the second phase and the matrix. It was also a function of the particle size and the content. It was confirmed that the rising R-curve behavior of Al2O3 containing 30 vol% SiC particles of 3${\mu}{\textrm}{m}$ was owing to the strong crack bridging by SiC particles. For Al2O3/ZrO2/SiC composites, the tensional stress from the 3${\mu}{\textrm}{m}$ SiC particles was large enough to activate the spontaneous transformation of the ZrO2. The crack extension resistance due to the particle bridging mechanism did not seem to be affected much by the coupled toughening, but its resultant toughness increase could be significantly smaller due to the dependency on the matrix toughness.

• Korean Chemical Engineering Research
• /
• v.59 no.2
• /
• pp.281-295
• /
• 2021

In this study, the direct amination of ethanol was performed over impregnated Ni on SiO2-Al2O3 mixed oxide catalysts prepared by varying Si/(Si + Al) molar ratio to 30 mol%. To characterize the physico-chemical properties of the catalysts used, X-ray diffraction (XRD), N2-physisorption, temperature-programmed desorption of iso-propyl alcohol (IPA-TPD), temperature-programmed desorption of ethanol (EtOH-TPD), temperature-programmed reduction with H2 (H2-TPR), H2-chemisorption and transmission electron microscopy (TEM) were used. The acidic property was continuously increased until Si/(Si + Al) = 30 mol% in SiO2-Al2O3 mixed oxides used. The dispersion of Ni metal and surface area, acid characteristics of the supported Ni catalyst have a complex effect on the catalytic reaction activity. The low reduction temperature of nickel oxide and acidic properties were beneficial to the formation of acetonitrile. In terms of conversion of ethanol, Ni/SiO2-Al2O3 catalyst with a molar ratio of 10 mol% Si/(Si+Al) showed the highest activity and a volcanic curve based on it. The tendency of results were consistent in the metal dispersion and catalytic activity.

• Journal of the Korean Ceramic Society
• /
• v.16 no.4
• /
• pp.206-212
• /
• 1979

The phase relations and microstructure appeared at 1700℃ in a system of Si3N4-Al2O3-SiO2 were studied. The samples were pressurelessly sintered at 1700℃ for 1hr and reheated at 1600℃ for 1hr under nitrogen atmosphere. The compounds formed were identified by X-ray diffraction method and the microstrues were observed by SEM. The stable phases appeared in this system were X-phase, Si2ON2, β'-Si3N4 and Mullite. From the results of those experiments, it was concluded that the X-phase has very close composition to that proposed by G, K. Layden, Si3Al6O12N2. SEM photographs showed that Si2ON2 was a plate phase and X-phase was a rectagular plate phase.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.12a
• /
• pp.42-44
• /
• 2003

최근 logic 소자의 gate oxide로 기존의 $SiO_2$, SiON보다 고유전, 작은 누설전류를 가지는 물질의 개발이 중요한 이슈가 되고 있다. 본 실험실에서는 Si 기판위에 $HfO_2$ 를 바로 증착하는 경우, 기판의 Si 이박막내로 확산하여 유전율이 저하되는 문제점을 인식하고, 기판과 $HfO_2$ 사이에 $AlO_x$를 방지막으로 사용하였다. 이 때, $AlO_x$의 Al precursor 는 TMA 로 고정하고, 산화제로는 $H_2O, O_2$-plasma, O_3$ 를 각각 사용하였다. 모든 $AlO_x/HfO_y$ 박막에서 매우 우수한 누설전류특성을 얻을 수 있었는데, 특히 $O_3$ 를 산화제로 사용한 $AlO_x$ 방지막의 경우 가장 우수한 특성을 보였다. 또한 질소 분위기에서 $800^{\circ}C$ 10 분간 열처리한 후, 방지막을 사용한 모든 경우에서 보다 향상된 열적 안정성을 관찰할 수 있었다.

• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1169-1175
• /
• 1994

Five Al2O3/SiC/metal composites with four different particle sizes of green SiC abrasive grains are grown by the directed oxidation of an commercially available Al-alloy. Oxidation was conducted in air at 100$0^{\circ}C$, 96 hours long. Slip casted SiC-fillers were placed on the alloy or SiC powder deposited up to the required layer thickness. Their microstructures are described and measurements of density, elastic constants, frexural strength, fracture toughness and work of fracture are reported. The results are compared with those of commercial dense sintered Al2O3. The properties of produced materials have a strong relationship to not only the properties of Al2O3, SiC, Al and Si but also to the phase share and phase distribution. The composite materials are dense (0.5% porosity), tough (KIC = 3.4~6.4 MPa{{{{ SQRT { m} }}), strong ({{{{ sigma }}B = 170~345 MPa) and reasonably shrinkage free producible. The reinforcements is attained mainly through the plastic deformation of ductile metal phase.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.418.2-418.2
• /
• 2016

$Al_2O_3$ passivation layer has excellent passivation properties at p-type Si surface. This $Al_2O_3$ layer forms thin $SiO_2$ layer at the interface. There were some studies about inserting thermal oxidation process to replace naturally grown oxide during $Al_2O_3$ deposition. They showed improving passivation properties. However, thermal oxidation process has disadvantage of expensive equipment and difficult control of thin layer formation. Wet chemical oxidation has advantages of low cost and easy thin oxide formation. In this study, $Al_2O_3$/$SiO_2/Si(100)$ interface was formed by wet chemical oxidation and PA-ALD process. $SiO_2$ layer at Si wafer was formed by $HCl/H_2O_2$, $H_2SO_4/H_2O_2$ and $HNO_3$, respectively. 20nm $Al_2O_3$ layer on $SiO_2/Si$ was deposited by PA-ALD. This $Al_2O_3/SiO_2/Si(100)$ interface were characterized by capacitance-voltage characteristics and quasi-steady-state photoconductance decay method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1989.06a
• /
• pp.66-69
• /
• 1989

After reviewing previous work done on two piezoelectric thin films(PZT, ZnO), ZnO thin piezofim of 1-3UM is fabricated by sputtering on the different substrates(i. e., P+Si/N-Si, SiO2/P+Si/ N-Si, Al/SiO2/ P+Si/ N+Si). The result shows that ZnO piezofilm on the Al has the best c-axis orientation. One of applications for the ZnO piezofilm as an microvalve to control liquid flow is introduced, and which can be controlled electrically and remotely.