• International Journal of Fluid Machinery and Systems
• /
• v.8 no.4
• /
• pp.294-303
• /
• 2015

The present study is conducted to identify a better design and optimal number of Francis runner blades for sediment laden high head micro hydropower site, Tara Khola in the Baglung district of Nepal. The runner is designed with in-house code and Computational Fluid Dynamics (CFD) analysis is performed to evaluate the performance with three configurations; 11, 13 and 17 numbers of runner blades. The three sets of runners were also investigated for the sediment erosion tendency. The runner with 13 blades shows better performance at design as well as in variable discharge conditions. 96.2% efficiency is obtained from the runner with 13 blades at the design point, and the runners with 17 and 11 blades have 88.25% and 76.63% efficiencies respectively. Further, the runner with 13 blades has better manufacturability than the runner with 17 blades as it has long and highly curved blade with small gaps between the blades, but it comes with 65% more erosion tendency than in the runner with 17 blades.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.107-112
• /
• 2012

Air flow and its pressure at electric fan according to three, four and five blades are analyzed in this study. As the number of blades increases at the same condition of specification, air tends to converge and becomes natural wind but higher power is consumed. And the velocity of wind is decreased as the space between winds becomes narrow. The turbulent flow is happened in the center of the body of revolution and the kinetic energy becomes largest in case of three blades. The pressure is decreased than atmospheric pressure from fan to outlet. As the number of blades increases, the pressure drop becomes smaller and is smallest in case of the fan with three blades. As the study result, The electric fan with three blades is thought to be effective in view of power consumption and design.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.11
• /
• pp.76-81
• /
• 2013

In this paper, a corona motor with blade type electrodes has been employed as a wind blower. The rotation speed was influenced significantly by the polarity of applied voltage and the number of blades. Therefore the effect of polarity of applied voltage and the number of blades on the electrical and mechanical fundamental properties of corona motor were investigated experimentally. The rotation speed decreased for increasing of number of blades, because the mass of blades increased. But the amount of air blow increased despite decreasing of the rotation speed, because air volume is not only influenced by rotation speed but also the number of blades and ionic wind which generated between blade tips and a induction electrode. Although space occupied by blades of the corona motor is smaller than the whole area of the blast pipe, wind rises a whole range of a wind blower for such reasons.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.60 no.1
• /
• pp.80-86
• /
• 2024

We analyzed the performance of hubless rim propellers based on the number of blades, maintaining a fixed pitch ratio and expanded area ratio, using computational fluid dynamics (CFD). Thrust coefficient, torque coefficient and efficiency according to the number of blades were analyzed. In addition, the pressure distribution on the discharge and suction sides of the blade was analyzed. As the advance ratio increases, the thrust coefficient decreases. The highest thrust was shown when the advance ratio was lowest. For the three, four, five and six-blades, the torque coefficient tended to decrease as the advance ratio increased. In the case of seven and eight-blades, the torque coefficient tended to increase as the advance ratio increased. The maximum efficiency was found when the advance ratio was 0.8. When the three-blade, it showed high efficiency at all advance ratios. A high pressure distribution was observed at the leading edge of the discharge blade, and a low pressure distribution was observed at the trailing edge. Applying a hubless rim-driven thruster with the three-blade can generate higher thrust and increase work efficiency.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.5
• /
• pp.357-363
• /
• 2003

There have been lots of studies on noise transmission analysis and noise reduction In ducts. In order to reduce the noise transmission in ducts. active noise cancellation techniques have often been employed and a rotation shaft with blades has sometimes been suggested. These Ideas were not successfully commercialized because of the limitation of real life such as size or application difficulties. This study investigated how a rotational shaft with blades could reduce the noise transmission in a duct. To do so, an assembly of the shaft and the $haft housing was built In the middle of a duct. and the clearance between the blades and the housing was 0.2 mm. The noise reduction was experimentally evaluated with respect to the number of blades. the rotation speed, and the rotation or stop. This paper showed that the noise reduction resulted in about 14∼19 dBA regardless of the three test conditions only If the blades always blocked the duct. And. the noise reduction increased due to the higher number of blades and the lower speed of the shaft.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.2
• /
• pp.52-57
• /
• 2009

The effects of number of blades on the hydraulic performance of the inducer were studied using a computational method. Inducers with number of blades from 2 to 4 were used for computations and the hydraulic performances of the inducers were compared. The computational results showed that the hydraulic performance decreased due to the increase of the skin friction loss at blade passages as the blade number increased. The results also showed that the strength of the backflow became weak because of the decrease of unfavorable pressure gradient as the blade number increased.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.3
• /
• pp.277-285
• /
• 2010

We examined the optimal shape of blades and efficiency of a self-power generator when the self-power generator using flow of the water in pipe as the power source was installed. Selected factors were the shape of blades, the number of blades, pitch angle, and the existence of separator. GAMBIT2.4 was used as a modeling program, FLUENT6.3, which is computational fluid dynamics simulation program, was used as an analytical model. In the case of a viscous model, k-epsilon standard model was chosen. As a result, when the number of blades was increased, the efficiency and maximum moment were enhanced slightly. The pitch of blades went up, and maximum moment was also increased. The optimal pitch of blade was 62.5 degree and the efficiency was increased by 30%. The efficiency was also increased when a separator was installed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.91-94
• /
• 2004

A cyclocopter with the cycloidal blades system can be the type of UAV which can combine the high-speed characteristics of the conventional airplane with the low-speed characteristics of the helicopter. The cycloidal blades system, which can be described as a horizontal rotary wing, offers powerful thrust levels, and a unique ability to change the direction of the thrust almost instantly. Rotor blades are designed to withstand tremendous transverse centrifugal loadings, and responding to a number of aerodynamic harmonic vibratory forcing frequencies. To reduce the weight and increase the strength, the blades are made of composite materials. The blades consist of the skin, spar, and trailing stiffener. In this study, static and dynamic behaviors of cyclocopter rotor blades are analyzed by using MSC/NASTRAN.

• IE interfaces
• /
• v.14 no.2
• /
• pp.140-147
• /
• 2001

In the turbine-blade manufacturing industry, turbine-blades are machined and then are assembled to form a circular roll of blades. The roll of blades should be balanced as much as possible, since otherwise the efficiency of the turbine generator might be damaged. A locking blade is a blade whose location is fixed and a non-locking blade is a blade whose location can be freely changed. In this paper, we study methods for balancing the weights of the rotating blades for a turbine where some blades are locking blades. The turbine-blade balancing problem is formulated into a mixed-integer programming problem, which turns out to be NP-hard. A heuristic method based on the number partitioning algorithm is developed and the computational experiments show very promising results.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2000.04a
• /
• pp.193-196
• /
• 2000

In the turbine-blade manufacturing industry, turbine-blades are machined and then are assembled to form a circular roll of blades. The roll of blades should be balanced as much as possible, since otherwise the efficiency of the turbine generator might degrade. We propose a heuristic method for balancing blades based on the number partitioning algorithm. The proposed method outperformed existing methods remarkably in terms of the accuracy with a negligible increase in the running time.