• Journal of Korean Vacuum Science & Technology
• /
• v.4 no.1
• /
• pp.18-22
• /
• 2000

For the enhancement of the nucleation density of the diamond film, we introduced the cyclic process. The cyclic process was carried out by the on/off control of CH$_4$ flow rate for a relatively short time (10 min), compared with the total reaction time (6 h). Prior to depositing the diamond film, we made the pretreated glass substrate via the unidirectional scratch using ∼l $\mu\textrm{m}$ size diamond powders. Diamond films were deposited on the pretreated glass substrate in a microwave plasma enhanced chemical vapor deposition (MPECVD) system. We observed the enhancement of the nucleation density of the diamond films caused by the cyclic process. Detailed surface morphologies of the substrate were investigated after the cyclic process. Based on these results, we discussed the cause for the enhancement of the nucleation density on the pretreated glass substrate by the cyclic process.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.636-644
• /
• 1997

The effect of various processing parameters, in particular the substrate and filament temperature, on the nucleation of diamond has been studied for the hot filament CVD process with a negative bias on the substrate. As far as the substrate temperature was maintained around the critical temperature of 73$0^{\circ}C$, the nucleation of diamond increased with increasing filament temperature. The maximum nucleation density of ~ 2$\times$109/$\textrm{cm}^2$ was obtained under the condition of filament temperature of 230$0^{\circ}C$, substrate temperature of 75$0^{\circ}C$, bias voltage of 300V, methane concentration of 20%, and deposition time of 2 hours. This nucleation density is about the same as those obtained in previous investigations. For fixed substrate temperatures, the nucleation density varies up to about 103 times depending on experimental conditions. This result is different from that of Reinke, et al. When the substrate temperature was above 80$0^{\circ}C$, a silkworm~shaped carbon phase was co-deposited with hemispherical microcrystalline diamond, and its amount increased with increasing substrate temperature. The Raman spectrum of the silkworm-shaped carbon was the same as that of graphitic soot. The silkworm-shaped carbon was etched and disappeared under the same as that of graphitic soot. The silkworm-shaped carbon was etched and disappeared under the deposition condition of diamond, implying that it did not affect the nucleation of diamond.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.3
• /
• pp.303-306
• /
• 1999

On the effect of substrate bias at first stage of diamond synthesis at lower substrate temperature(approximately 673K) using microwave plasma CVD and effect of reaction gas system for the bias enhanced nucleation were studied. The reaction gas was mixture of methane and hydrogen or carbon monoxide and hydrogen. The nucleation density of applied bias -150V using $CH_4-H_2$ reaction gas system, significantly higher than that of $C-H_2$ reaction gas system. When the $CH_4-H_2$ reaction was used, nucleation density was increased because of existence of SiC as a interface for diamond nucleation. By use of this negative bias effect for fabrication of CVD diamond film using two-step diamond growth without pre-treatment, fabrication of the diamond film consist of diamond grains $0.2\mu\textrm{m}$ in diameter was demonstrated

• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.159-162
• /
• 1997

Diamond was uniformly nucleated on large area Si(001) substrate (3cm$\times$4cm) using the low pressure magnetoactive microwave plasma chemical vapor deposition. $CH_4/He$ gas mixture was used as source gas in order to obtain high radical density in the nucleation enhancement step. $CH_3$radical density was measured by means of infrared laser absorption spectroscopy. The effect of substrate bias voltage on diamond nucleation was examined. The results showed that a suitable positive bias voltage appled to the substrate with respect to the chamber could enhance diamond nucleation while a negative bias voltages leaded to deposition of only non-diamond phase carbon.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.125-129
• /
• 2016

In this study, we have investigated a high-temperature AlN nucleation layer and AlGaN epilayers on c-plane sapphire substrate by low-pressure metal-organic chemical vapor deposition (LP-MOCVD). High resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM), scanning electron microscope (SEM) and Raman scattering measurements have been exploited to study the crystal quality, surface morphology, and residual strain of the HT-AlN nucleation layer. These analyses reveal that the insertion of an LT-AlN nucleation layer can improve the crystal quality, smooth the surface morphology of the HT-AlN nucleation layer and further reduce the threading dislocation density of AlGaN epifilms. The mechanism of inserting an LT-AlN nucleation layer to enhance the optical properties of HT-AlN nucleation layer and AlGaN epifilm are discussed from the viewpoint of driving force of reaction in this paper.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.2
• /
• pp.122-130
• /
• 1996

In an effort to learn more about the reaction mechanisms which lead to the compound nucleation at the interface of cobalt and silicon, electrical noise properties has been investigated for cobalt thin films deposited on silicon substrates by the electron beam evaporation and rf sputtering techniques. Microstructural variations at the Co/Si interfaces have been observed by transmission electronmicroscopy. Amorphous structures are observed at the Co/Si interfaces for samples whose cobalt thicknesses are less than 4nm and a polycrystalline compound nucleation has been occurred for thicker films. 1/f noise power same samples, and the spetral density has been normalized. The amplitude of 1/f noise power spectral density shows a gradual increase as the cobalt thickness is increased, and the amplitude has dropped abruptly after the compound nucleation. The variations of the noise parameters areassumed to be an indiction of the phase transformation along the nucleation reaction path, and amplitude has been interpreted as instabilities of the Co/Si interfacial structures.

• Transactions of Materials Processing
• /
• v.22 no.8
• /
• pp.450-455
• /
• 2013

In the current study, a new dynamic recrystallization model for predicting high temperature flow stress is developed based on a physical model and the mean field theory. In the model, the grain aggregate is assumed as a representative volume element to describe dynamic recrystallization. The flow stress and microstructure during dynamic recrystallization were calculated using three sub-models for work hardening, for nucleation and for growth. In the case of work hardening, a single parameter dislocation density model was used to calculate change of dislocation density and stress in the grains. For modeling nucleation, the nucleation criterion developed was based on the grain boundary bulge mechanism and a constant nucleation rate was assumed. Conventional rate theory was used for describing growth. The flow stress behavior of pure copper was investigated using the model and compared with experimental findings. Simulated results by cellular automata were used for validating the model.

• Korean Journal of Materials Research
• /
• v.14 no.5
• /
• pp.363-367
• /
• 2004

Recently ZnO epitaxial layers have been widely studied as a semiconductor material for optoelectronic devices. Sapphire and silicon are commonly selected as substrate materials for ZnO epitaxial growth. In this communication, we report the effect of the ECR plasma pretreatment of sapphire and silicon substrates on the nucleation in the ZnO ALE (atomic layer epitaxy). It was found that ECR plasma pretreatment reduces the incubation period of the ZnO nucleation. Oxygen ECR plasma enhances ZnO nucleation most effectively since it increases the hydroxyl group density at the substrate surface. The nucleation enhancing effect of the oxygen ECR plasma treatment is stronger on the sapphire substrate than on the silicon substrate since the saturation density of the hydroxyl group is lower at the sapphire surface than that at the silicon surface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.552-556
• /
• 1998

Diamond thin films were deposited on Si substrate using $CH_4 and H_2$mixed gas by RF plasma CVD. Prior to deposition, the substrate surface was mechanically scratched with the diamond paste of $3{\mu}m$ to improve the density of nucleation sites. The microstructure of diamond films deposited with methane(0.5%~2%) at the reaction pressure ranging from 20 torr to 50torrr were studied by a scanning electron microscope. It was observed in the deposited diamond films that the nucleation density decreased and crystallinity increased with decreasing the methane concentration. However, the nucleation density and crystallinity were decreased with decreasing the process pressure.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.239-244
• /
• 2019

Two hydrogenation surface modifications, namely hydrogen atmosphere heat treatment and hydrogen plasma treatment, were found to lead to improved dispersion of nanodiamond (ND) seed particles and enhanced nucleation density for deposition of smooth ultrananocrystalline diamond (UNCD) film. After hydrogenation, the C-O and O-H surface functionalities on the surface of nanodiamond particles were converted to the C-H surface functionalities, and the Zeta potential was increased. As the degree of dispersion was improved, the size of nanodiamond aggregates decreased significantly and nucleation density increased dramatically. After hydrogen heat treatment at 600℃, average size of ND particles was greatly reduced from 3.5 ㎛ to 34.5 nm and a very high nucleation of ~3.9 × 10¹¹ nuclei/㎠ was obtained for the seeded Si surface.