• 대한기계학회논문집A
• /
• 제37권11호
• /
• pp.1361-1369
• /
• 2013

본 연구에서는 다공홀 인젝터 내부 유동에 대한 CFD 시뮬레이션 해석(ANSYS 13.0 CFX)을 직접 수행하였다. 이러한 결과를 바탕으로 인젝터 노즐 설계변수가 캐비테이션에 미치는 영향을 파악하기 위해 실험계획법이 적용되었다. 각 설계변수의 설계민감도 및 신호 대 잡음비 분석을 위해 캐비테이션 유동에 영향을 미친다고 판단되는 설계변수는 노즐 홀 직경, 노즐 홀 길이, 노즐 홀 각도 및 노즐 홀의 K-factor로 지정하였다. 또한 16 개 실험점으로 각 변수의 영향을 분석하였다. 본 연구에서 노즐 내부유동을 파악하기 위하여 수치해석 프로그램과 신호 대 잡음비 분석이 본 논문에 적용되었고 그 결과, K-factor의 변화가 노즐 홀 길이와 노즐 홀 각도의 변화보다 인젝터 내부 캐비테이션 생성에 미치는 영향이 더 크다는 것을 알 수 있었다.

• Journal of Biosystems Engineering
• /
• 제25권6호
• /
• pp.463-470
• /
• 2000

For maximum seeding efficiency of a nozzle type seeder, the performance of the nozzle should be considered sufficiently. This study was carried out to investigate the optimum operating conditions of a seeder attached the vacuum nozzle which was modified syringe needle acting on the plug seedling tray and the seed plate. Such operating factors as the hole diameter of the nozzle (d), the distance from the nozzle tip to the bottom plate of seed hopper(D) the absorbing air pressure of the nozzle tip(P) the bounding height of seed from the vibrated bottom plate of seed hopper and the seeding speed were selected based on the weight of a grain of seed(W). The treated materials were pepper seed as the flat type, cucumber seed as the oval type and radish seed as the spherical type. The optimum operating conditions of the experimental seeder were revealed as follows: 1. The height of the seed bounding from the bottom plate of seed hopper and the distance from nozzle tip to bounded seed were 5 mm and 0.5 mm at all seeds. The hole diameter of the nozzle and the absorbing pressure for pepper seed, cucumber seed and radish seed was 0.45 mm, 0.65 mm. 0.65mm and 39.2 kPa, 88.3 kPa, 58.8 kPa, respectively. 2. The absorbing pressure P was represented as P=η.4W/$\pi$d$^2$ where η was 100. The seeding speed using a 128 cell tray was 2.4 cm/s which was same transfer as 2.5 trays per minute. 3. The maximum seeding rate in case of the pepper seed was 97% the cucumber seed was 95% and the radish seed was 100% under the optimum operating conditions of the seeder.

• Journal of Mechanical Science and Technology
• /
• 제19권11호
• /
• pp.2040-2052
• /
• 2005

The present paper centers on the establishment of a quantified relationship between the macroscopic visual parameters of a Diesel spray and its most influential factors. The factors considered are the ambient gas density, as an external condition relative to the injection system, and nozzle hole diameter and injection pressure as internal ones. The main purpose of this work is to validate and extend the different correlations available in the literature to the present state of the Diesel engine, i.e. high injection pressure, small nozzle holes, severe cavitating conditions, etc. Five mono-orifice, axi-symmetrical nozzles with different diameters have been studied in two different test rigs from which one can reproduce solely the real engine in-cylinder air density, and the other, both the density and the pressure. A parametric study was carried out and it enabled the spray tip penetration to be expressed as a function of nozzle hole diameter, injection pressure and environment gas density. The temporal synchronization of the penetration and injection rate data revealed a possible explanation for the discontinuity observed as well by other authors in the spray's penetration law. The experimental results obtained from both test rigs have shown good agreement with the theoretical analysis. There have been observed small but consistent differences between the two test rigs regarding the spray penetration and cone angle, and thus an analysis of the possible causes for these differences has also been included.

• 한국전산유체공학회지
• /
• 제15권1호
• /
• pp.56-63
• /
• 2010

Since emission regulations for vehicles have become more stringent, SCR technology has drawn a strong attention in order to reduce NOx emissions. Optimal design of a reductant injection nozzle and a multi-hole plate located between the cone and catalyst is critical in that the uniform distribution of reductant is necessary to maximize the NOx conversion efficiency and minimize the slip of reductant in SCR. In this work, an LPG fuel(C3H8 in vapor state) was used as a reductant for LPG vehicles. A Realizable k-$\varepsilon$ model is used for turbulence, and SCR body is defined as porous media with inertia and viscous resistances measured in this work. Effect of the number of nozzle holes on the flow mixing index was analyzed, which revealed that a four hole nozzle shows the best performance in terms of uniformity of flow. An installment of a multi-hole plate at the entrance of catalyst was evaluated with flow mixing index, uniformity of flow, and pressure drop. A multi-hole plate with gradual hole diameter change in three steps showed the best uniformity of flow within the conditions suggested in this work.

• 한국농공학회지
• /
• 제17권4호
• /
• pp.3991-4000
• /
• 1975

It is the aim of this study to investigate the influence of the factors in the sprayer nozzle for the travelling distance and to get nozzle design data in relation to the nozz1e with and without swirl plate. The factors of sprayer nozzle are composed of the spraying pressure, the helical angle of swirl plate, the helical groove depth of swirl plate, the distance of vortex chamber the slope of nozz1e cap, the curvature of nozzle cap and the hole diameter of nozz1e cap. The travelling distance and the size of sprayed particle are experimeted indoors by the factorial arrange-ment according to the 5 each level of the above factors. The results of this stupy are summarized as follows; 1. In the nozzle with swirl p1ate there were remarkable significance among factors each other, while without swirl plate were no significance. 2. The helical angle and groove depth in the nozzle with swirl plate were the highest effective factors. The effect of helical angle was very remarked in the quadratic curve with minium value. 3. The correlation betweenthe travelling distance and the sprayed particle size was no high and under 250 micron in the case with swirl plate, and there was higher correlation in the case without swirl plate. 4. The new ideal development of the swirl plate using of the most effective helical angle and groove depth will probably show the possiblities to make effective travelling distance over 8 meters and more over and to make average particle diameter under 300 micron.

• 대한설비공학회지:설비저널
• /
• 제16권1호
• /
• pp.89-102
• /
• 1987

Experiments have been carried out to study the atomisation characteristics of superheated liquid(water) jet injected into the atmosphere through a single-hole nozzle. In present experi-mental range, superheated liquid jet has been observed to be atomised in two-phase effluent type; that is, spray formed by the bubble nucleation in the nozzle. In case of liquid injection through a long nozzle (L/D=29.09), the critical superheat for occurrence of two-phase effluent atomisa-tion can be determined from sudden change of spray angle. Sauter mean diameter of the spray droplets decreases as the degree of superheat increases. For the short nozzle (L/D=7.27), mean diameter increases with the injection pressure, while it decreases for the long nozzle; however for the long nozzle the effect of injection pressure is not significant compared with the short nozzle. For the short nozzle the uniformity of drop size distribution increases with increasing the degree of superheat, but for the long nozzle the effect of superheat on the uniformity is not appreciable.

• 해양환경안전학회지
• /
• 제24권7호
• /
• pp.939-944
• /
• 2018

청정소화약제는 지구오존층 보호를 위해 발효된 몬트리올 의정서에 따라 할론 1211 및 할론 1310을 대체할 수 있는 약제를 말한다. 국 내외적으로는 청정소화약의 시스템 표준화와 성능평가가 수행되고 있다. 본 논문은 일반적인 청정소화약제 시스템을 바탕으로 다양한 노즐의 형상에 대한 모델링 및 수치해석을 수행하여 최적의 노즐 형상을 제안하였다. Type A와 B의 2가지 형상에 대한 노즐의 3차원 모델링을 통해 노즐의 분출속도가 개선될 수 있도록 하였다. 2가지 형상의 노즐에 대하여 유동해석을 실시하였으며 노즐의 홀 직경을 다르게 하여 가스속도 및 압력분포를 측정하였다. 측정결과 노즐 홀 수 및 직경에 따라 노즐출구에서 분출속도가 달라지는 것을 확인 할 수 있었으며 노즐 홀 직경에 관계없이 유량은 압력이 증가함에 따라 증가하는 경향을 나타내었다. 실험을 통해 얻어진 결과를 바탕으로 노즐 직경이 5 mm인 경우의 K-factor값이 $101.8l/min{\cdot}bar^{-0.5}$임을 확인하였으며, 최종적으로 노즐 홀 5 mm인 12개의 홀이 2층 구조로 되어 있는 형상의 노즐을 제안하였다.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1330-1336
• /
• 1990

The factors to act on atomization of liquid fuel are viscosity, geometric shape of nozzle, atomizing pressure, etc. Most of high viscous liquid fuels show decrease in viscosity by raising the preheat temperature, but the viscosity of liquid fuel like CWM does not readily change with fuel temperature. As an experimental study to investigate the atomizing characteristics of CWM, CWM fuel is atomizing with a twin-fluid atomizer, and the effects of the geometric shape of spray nozzle on atomization are investigated by measuring the Sauter`s Mean Diameter (SMD) of CWM. The summarized results obtained in this study are as follows ; (1) As the ratio of the mass flows of atomizing air to that of fuel (W$_{a}$ /W$_{1}$) increases, 능 decreases when fuel temperature is constant. (2) At the ratio (t/d) 4 of thickness (t) of spray nozzle hole to the diameter (d) of the hole, there is the best atomization. And SMD decreases when t/d is between 1 to 4 and increases when t/d > 4.

• 한국기계가공학회지
• /
• 제12권3호
• /
• pp.41-47
• /
• 2013

This study was carried out to improve the design of fuel injection nozzle for marine medium speed diesel engine. For this purpose, fuel injection nozzle was modeled and simulated using CATIA V5R19 and FLUENT & MSC Nastran. Analyses of flow and heat transfer, respectively, were performed to find the optimal design of fuel injection nozzle. As the results, big pressure drop, which may lead to cavitation damage, was occurred at inlet of fuel injection hole with diameter 0.3mm. Furthermore, it was confirmed that the increase of mean temperature of fuel injection nozzle was almost a half in comparison with that of fuel injection nozzle tip.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권3호
• /
• pp.180-184
• /
• 2016

국제기구 및 각국의 정부는 인간의 건강 및 환경을 보호하기 위해 선박의 배기가스 규제를 엄격히 적용하고 있다. 함정은 이러한 배기가스 규제 적용 대상에서 제외되고 있지만 최근 미국, 영국 등 일부 선진국에서는 함정으로 야기되는 대기환경오염을 방지하기 위해 전기추진체계 시스템을 도입하는 등 다양한 개선 방법을 적용하고 있다. 본 연구에서는 함정용 디젤엔진의 매연 발생 문제 해결을 위해 노즐 직경을 축소 변화시키고 분사압력을 증가시켜 배기가스 발생량 측정과 오염물질조사 방법론을 이용해 저부하시 매연 문제가 개선된 것을 확인하였다. 동시에 그 영향을 유량방정식과 함정시험평가서를 통해 노즐 직경 축소 결과 연료 소비량이 감소되는 것을 확인하였다.