• 한국항공우주학회지
• /
• 제34권10호
• /
• pp.24-31
• /
• 2006

본 논문에서는 유연수지 복합재료에 대하여 기하학적 비선형해석을 수행하였다. 실제 랜덤한 섬유배열을 사각배열과 육각배열로 가정하고 각각에 대해 단위구조를 정의하였다. 다양한 하중상태를 수치적으로 모사하여 단위구조해석을 통해 전체 구조물의 응력-변형률 선도를 예측하였고 이로부터 등가물성치를 계산하였다. 해석시 유연수지의 초탄성 성질을 정의하기 위해 Mooney-Rivlin모델을 사용하였다. 계산결과, 유연수지 복합재료 구조물은 변형률 증가에 따라 비선형의 응력-변형률 관계를 보였다. 비선형성은 횡방향 하중 상태에서 더욱 두드러지게 나타났으며, 이 경우 복합재 단면의 섬유배열 형태에 따라 상당한 차이를 보여주었다.

• 한국가스학회지
• /
• 제13권1호
• /
• pp.40-44
• /
• 2009

LNG 저장탱크의 대형화 추세에 맞춰 대형화, 건설비용 등에 있어 상대적으로 유리한 강재 지붕형 LNG 저장탱크에 대한 구조안전성을 기존의 콘크리트 지붕형 저장탱크와 비교 평가하였다. 20만$k{\ell}$ 강재 지붕형 탱크와 콘크리트 지붕형 탱크에 대해서 정상운전상태, LNG 유출상태 및 지진하중상태의 주요 하중조합조건에서 유한요소해석기법을 이용하여 해석하고, 벽체, 바닥 및 지붕의 강도비를 통해서 구조안전성을 정량적으로 평가하였다.

• Journal of Electrical Engineering and Technology
• /
• 제12권4호
• /
• pp.1566-1574
• /
• 2017

When the inter-turn short circuit (ITSC) fault occurs, the distortion of the magnetic field is serious. The motor loss variations of each part are obvious, and the motor temperature field is also affected. In order to obtain the influence of the ITSC fault on the motor temperature distribution, firstly, the normal and the fault finite element models of the permanent magnet synchronous motor (PMSM) were established. The magnetic density distribution and the eddy current density distribution were analyzed, and the mechanism of loss change was revealed. The effects of different forms and degrees of the fault on the loss were obtained. Based on the loss analysis, the motor temperature field calculation model was established, and the motor temperature change considering the loop current was analyzed. The influence of the fault on the motor temperature distribution was revealed. The sensitivity factors that limit the motor continuous operation were obtained. Finally, the correctness of the simulation was verified by experiments. The conclusions obtained are of great significance for the fault and high temperature demagnetization of the permanent magnet analysis.

• Earthquakes and Structures
• /
• 제9권4호
• /
• pp.699-718
• /
• 2015

The effect of reinforcing concrete members with high strength steel bars with yield strength up to 600 MPa on the overall seismic behavior of concrete moment frames was studied experimentally and numerically. Three geometrically identical plane frame models with two bays and two stories, where one frame model was reinforced with hot rolled bars (HRB) with a nominal yield strength of 335 MPa and the other two by high strength steel bars with a nominal yield strength of 600 MPa, were tested under simulated earthquake action considering different axial load ratios to investigate the hysteretic behavior, ductility, strength and stiffness degradation, energy dissipation and plastic deformation characteristics. Test results indicate that utilizing high strength reinforcement can improve the structural resilience, reduce residual deformation and achieve favorable distribution pattern of plastic hinges on beams and columns. The frame models reinforced with normal and high strength steel bars have comparable overall deformation capacity. Compared with the frame model subjected to a low axial load ratio, the ones under a higher axial load ratio exhibit more plump hysteretic loops. The proved reliable finite element analysis software DIANA was used for the numerical simulation of the tests. The analytical results agree well with the experimental results.

• Computers and Concrete
• /
• 제8권6호
• /
• pp.735-755
• /
• 2011

The capability of a multi-directional fixed smeared crack constitutive model to simulate the flexural/punching failure modes of fiber reinforced concrete (FRC) laminar structures is discussed. The constitutive model is implemented in a computer program based on the finite element method, where the FRC laminar structures were simulated according to the Reissner-Mindlin shell theory. The shell is discretized into layers for the simulation of the membrane, bending and out-of-plane shear nonlinear behavior. A stress-strain softening diagram is proposed to reproduce, after crack initiation, the evolution of the normal crack component. The in-plane shear crack component is obtained using the concept of shear retention factor, defined by a crack-strain dependent law. To capture the punching failure mode, a softening diagram is proposed to simulate the decrease of the out-of-plane shear stress components with the increase of the corresponding shear strain components, after crack initiation. With this relatively simple approach, accurate predictions of the behavior of FRC structures failing in bending and in shear can be obtained. To assess the predictive performance of the model, a punching experimental test of a module of a façade panel fabricated with steel fiber reinforced self-compacting concrete is numerically simulated. The influence of some parameters defining the softening diagrams is discussed.

• Steel and Composite Structures
• /
• 제36권2호
• /
• pp.229-247
• /
• 2020

This study analyzed stresses in concrete and its reinforcement, computing the additional loading transferred by concrete creep. The loading varied from zero, structure exclusively under its self-weight, up to the critical buckling load. The studied structure was a real, tapered, reinforced concrete pole. As concrete is a composite material, homogenizing techniques were used in the calculations. Due to the static indetermination for determining the normal forces acting on concrete and reinforcement, equations that considered the balance of forces and compatibility of displacement on cross-sections were employed. In the mathematical solution used to define the critical buckling load, all the elements of the structural dynamics present in the system were considered, including the column self-weight. The structural imperfections were linearized using the geometric stiffness, the proprieties of the concrete were considered according to the guidelines of the American Concrete Institute (ACI 209R), and the ground was modeled as a set of distributed springs along the foundation length. Critical buckling loads were computed at different time intervals after the structure was loaded. Finite element method results were also obtained for comparison. For an interval of 5000 days, the modulus of elasticity and critical buckling load reduced by 36% and 27%, respectively, compared to an interval of zero days. During this time interval, stress on the reinforcement steel reached within 5% of the steel yield strength. The computed strains in that interval stayed below the normative limit.

• Structural Engineering and Mechanics
• /
• 제38권1호
• /
• pp.65-79
• /
• 2011

Concrete hydraulic structures such as: Dams, Intake Towers, Piers and dock are usually recognized as" Vital and Special Structures" that must have sufficient safety margin at critical conditions like when earthquake occurred as same as normal servicing time. Hence, to evaluate hydrodynamic pressures generated due to seismic forces and Fluid-Structure Interaction (FSI); introduction to fluid-structure domains and interaction between them are inevitable. For this purpose, first step is exact modeling of water-structure and their interaction conditions. In this paper, the basic equation involved the water-structure-foundation interaction and the effective factors are explained briefly for concrete hydraulic structure types. The finite element modeling of two concrete gravity dams with 5 m, 150 m height, reservoir water and foundation bed rock is idealized and then the effects of fluid domain and bed rock have been investigated on modal characteristic of dams. The analytical results obtained from numerical studies and modal analysis show that the accurate modeling of dam-reservoir-foundation and their interaction considerably affects the modal periods, mode shapes and modal hydrodynamic pressure distribution. The results show that the foundation bed rock modeling increases modal periods about 80%, where reservoir modeling changes modal shapes and increases the period of all modes up to 30%. Reservoir-dam-foundation interaction increases modal period from 30% to 100% for different cases.

• Structural Engineering and Mechanics
• /
• 제34권3호
• /
• pp.351-366
• /
• 2010

A novel system identification and structural health assessment procedure of steel framed structures with semi-rigid connections is presented in this paper. It is capable of detecting damages at the local element level under normal operating conditions; i.e., serviceability limit state. The procedure is a linear time-domain system identification technique in which the structure responses are required, whereas the dynamic excitation force is not required to identify the structural parameters. The procedure tracks changes in the stiffness properties of all the elements in a structure. It can identify damage-free and damaged structural elements very accurately when excited by different types of dynamic loadings. The method is elaborated with the help of several numerical examples. The results indicate that the proposed algorithm identified the structures correctly and detected the pre-imposed damages in the frames when excited by earthquake, impact, and harmonic loadings. The algorithm can potentially be used for structural health assessment and monitoring of existing structures with minimum disruption of operations. Since the procedure requires only a few time points of response information, it is expected to be economic and efficient.

• 조명전기설비학회논문지
• /
• 제26권9호
• /
• pp.57-63
• /
• 2012

The basic purpose of grounding is for human safety and normal operation of system related to electrical shock hazard by faults of electrical equipments. A grounding electrode is defined as a conducting element that connects electrical systems and/or equipment to the earth. The lowest possible resistance connection to the earth is sought from the grounding electrode. The grounding electrode is the foundation of the electrical safety system. The resistance to ground of vertical electrodes buried in the two deference soil structures has been analyzed for a length of electrodes and soil parameters. The equation of ground resistance of vertical electrodes are Tagg's equation for uniform soil models, and modified equation of Dwight equation for two-layer soil model. In this paper, compared with results of two equations are calculated values of vertical electrode in uniform and two-layer soil models.

• 한국통신학회논문지
• /
• 제19권2호
• /
• pp.231-241
• /
• 1994

ISDN 베어러 서비스의 일반적 형태인 가입자간 일대일 접속을 벗어나 다수의 가입자간에 동시 접속을 제공하며 접속상의 텔리 서비스를 제어할 수 있는 새로운 통신망 요소로서 서비스노드의 개념을 제안하였다. 이러한 개념이 실현될 경우 ISDN에 접속된 비특정 다자간 회의형 멀티미디어 서비스 제공이 가능한 것이다. 이에대한 일차 연구로서 본 논문에서는 일반적인 회의형 멀티미디어 서비스 제공이 가능할 것이다. 이에대한 일차 연구로서 본 논문에서는 일반적인 회의형 서비스의 속성을 도출하고 이를 ISDN으로 제공키 위해 요구되는 절차와 방법에 대해 검토 하였다. 이를 바탕으로 서비스노드가 갖추어야할 일반 요구사항을 정의하고 구조를 제시함으로써 서비스노드 개념을 구체화 하였다.