• 비파괴검사학회지
• /
• 제29권3호
• /
• pp.235-241
• /
• 2009

Composite wood materials are very sensitive to water and inspection without any coupling medium of a liquid is really needed to wood materials due to the permeation of coupling medium such as water. However, air-coupled ultrasound has obvious advantages over water-coupled experimentation compared with conventional C-scanner. In this work, it is desirable to perform contact-less nondestructive evaluation to assess wood material homogeneity. A wood material was nondestructively characterized with non-contact and contact modes to measure ultrasonic velocity using automated data acquisition software. We have utilized a proposed peak-delay measurement method. Also through transmission mode was performed because of the main limitation for air-coupled transducers, which is the acoustic impedance mismatch between most materials and air. The variation of ultrasonic velocity was found to be somewhat difference due to air-coupled limitations over conventional scan images. However, conventional C-scan images are well agreed with increasing the resin-infiltrated time as expected. Finally, we have developed a measurement system of an ultrasonic velocity based on data acquisition software for obtaining ultrasonic quantitative data for correlation with C-scan images.

• 한국자기학회지
• /
• 제26권1호
• /
• pp.24-30
• /
• 2016

지하에 매설된 가스배관에 발생한 결함 유무를 판별하는 방법으로는 자기누설 신호를 탐지하는 비파괴검사 기법이 사용되어져 왔다. 지하 매설된 배관은 높은 가스 운용압력과 습기와 같은 외부환경에 노출되어 있어 금속부식과 같은 결함들이 군집하여 발생한다. 군집 결함들에 의해 발생한 자기누설 신호는 단일결함 신호와 비교하여 왜곡된 형태를 가지며, 왜곡된 결함 신호의 분포는 최종적으로 결함의 형상 추정을 어렵게 한다. 본 논문에서는 30인치 직경의 배관을 기준으로 다중 결함의 배치 형태와 거리를 달리하며 신호 패턴을 분석하고, 인접한 결함의 분리 가능 여부와 신호 보정을 고려한 개선된 결함 판정 알고리즘을 제안하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.247-248
• /
• 2007

• 품질경영학회지
• /
• 제7권1호
• /
• pp.26-34
• /
• 1979

This paper intends to decide the optimum OC curves and to find the minimized ${\alpha},{\beta}$-risk based upon the Linear Cost Model (L. C. M.) for the destructive or nondestructive acceptance sampling inspection plan. For the solution from the L. C. M., the author used the prior-distribution on some assumptions.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.403-412
• /
• 1993

This paper presents the progress of the development of a nondestructive technique for the classification of normal, septicemic , and cadaver poultry carcasses by the Instrumentation and Sensing Laboratory at Beltsville, Maryland, U.S.A. The Sensing technique is based on the diffuse reflectance spectroscopy of poultry carcasses.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.280-285
• /
• 2004

In this study, we made a comparative study of backpropagation neural network and probabilistic neural network and bayesian classifier and perceptron as shape recognition algorithm of welding flaws. For this purpose, variables are applied the same to four algorithms. Here, feature variable is composed of time domain signal itself and frequency domain signal itself. Through this process, we comfirmed advantages/disadvantages of four algorithms and identified application methods of four algorithms.

• International Journal of Safety
• /
• 제8권1호
• /
• pp.6-9
• /
• 2009

The crack in a J85 engine V.G. actuator arm shaft for a bell crank on the engine compressor was investigated. The crack was observed in twenty two shafts during the inspection of 238 shafts. The failure analysis of shaft cracks was performed by chemical composition analysis using ICP(Inductively Coupled Plasma) and by fracture surface and microstructure analysis using FE-SEM and optical microscope. The crack initiated from the top and bottom and propagated to the center along the grain boundaries. From the chemical composition analysis, the fractography of the fracture surface and the microstructure, it was found that the failure mechanism of the shafts is the inclusion-related intergranular decohesion crack. The inclusion was found out from MnS particle by EDS(Energy Dispersive Spectroscopy). The crack initiated MnS inclusion in the grain boundary and propagated with the increase of applied shear stress during long operation. In order to prevent the fracture, NDI(Nondestructive inspection) is needed periodically as recommended.

• Journal of Biosystems Engineering
• /
• 제23권1호
• /
• pp.67-74
• /
• 1998

A nondestructive quality inspection technique using acoustic impulse response method was developed for eggshell inspection. An experimental system was built to generate the impact force, to measure the response signal and to analyze the frequency spectrum. This system includes an impulse generating unit, an egg holding seal a microphone with preamplifier, and a DSP board installed on Personal Computer. A simple algorithm .was developed for crack detection. Using the developed system with algorithm, crack detection ability was evaluated and the error rate to estimate the normal egg as cracked was found to be 4% and the error rate to estimate the cracked egg as normal was also found to be 4%. This system could be adopted in industry with some modification.

• Journal of Welding and Joining
• /
• 제22권5호
• /
• pp.32-37
• /
• 2004

Application of bonding by adhesives can be found in many industries, particularly in advanced technological domains such as aeronautical and space, automobile and electronics industries. Periodic inspection with conventional ultrasonic NDE techniques is capable of indicating the presence and possible location of crack. Continuous ultrasonic attenuation monitoring has potential to supply information. This article discusses the use of pulse-echo ultrasonic testing for the inspection of adhesive bonds between metal sheets. The method is based on the measurement of the reflection coefficient at the metal/adhesive interface. By means of a control experiment it is shown that Quantitative Nondestructive Evaluation in Adhesive Joints are evaluated together with Ultrasonic Testing and Fracture Testing.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.127.5-127
• /
• 2001

The 3-dimensional measuring machine by using an ultrasonic sensor is used one of the NDE (Nondestructive Evaluation). It is applied to the inspection of pipelines, boreholes, pressure vessel and tank, and so on. On particular when a harsh environment prohibits the use of moving mechanical parts. The 3-dimensional measuring machine by using an ultrasonic sensor, which measure 1-dimensional information and 2-dimensional information simultaneously from a target of inspection, and then re construct 3-dimensional information. So we can find the situation in progress and predict remaining life and corrosion without destructive examination. It´s a point of excellence that the 3-dimensional measuring machine is portable.